4 Operation
Advantage:
▪ Before and after your holiday, your normal schedule will be used.
▪ During your holiday, you save energy and prevent your house
from freezing.
Usage example: You come home during your holiday
If you are in the following situation:
▪ You configured and activated the holiday mode (Away).
▪ During your holiday, you come home for a few hours and want to
use your normal schedule.
Then you can do the following:
1 Deactivate the holiday mode.
2 When you go away again, activate the holiday mode again.
Advantage:
You do NOT have to change your schedule or holiday configuration.
4.6.3
Reading out information
About reading out information
The amount of information you can read out in the menu structure
([6]: Information) depends on your user permission level:
▪ End user (= default)
▪ Adv. end user: You can read out more information.
To switch between user permission levels (End user and
Advanced end user)
1 Go to [6] or any of its submenus:
2 Press
for more than 4 seconds.
Result: The user permission level switches to Adv. end user.
Additional information is displayed and "+" is added to the menu
title.
3 If you do NOT press any button for more than 1 hour or press
again for more than 4 seconds, the user permission level
switches back to End user.
To read out information
Go to [6]:
> Information.
Possible readout information
If user permission level = End user, you can read out the following
information:
In menu...
[6.1] Sensor information
[6.2] Energy metering
[6.3] Error handling
[6.4] User permission level
If user permission level = Adv. end user, you can read out the
following additional information:
In menu...
[6.1] Sensor information
[6.2] Energy metering
User reference guide
14
> Information.
You can read out...
Room, tank or DHW, and outside
temperature.
Produced energy, consumed
electricity, and consumed gas.
Error history and contact/
helpdesk number.
Current user permission level.
You can read out...
Room, tank or DHW, outside,
and leaving water temperature.
(If applicable)
Produced energy, consumed
electricity, and consumed gas.
In menu...
[6.5] Actuators
[6.6] Operation modes
[6.7] Running hours
[6.8] Version
4.6.4
Configuring date, time, units of
measurement, contrast and backlight
To configure time and date
Go to [1]:
> Set time/date.
To configure units of measurement
Go to [7.6]:
> User settings > Unit of measurement.
Possible units of measurement settings
Setting
Decimal point
Temperature
Produced energy
Flow
To configure the contrast of the user interface
Go to [7.1.1]:
> User settings > Display > Contrast.
To configure the backlit LCD time of the user interface
Go to [7.1.2]:
> User settings > Display > Backlit LCD time.
4.6.5
Configuring user profile and home pages
To set a user profile
1 Go to [7.1.3]:
> User settings > Display > User profile.
2 Select a user profile and press
Possible user profiles
If user profile = Detailed, you can see and do more on the home
pages.
User profile
Basic
20.0°C
Actual temperature
Detailed
20.0°C
Actual temperature
Scheduled
Tue
17:30
You can read out...
Status/mode of each actuator.
Example: Domestic hot water
pump ON/OFF.
Current operation mode.
Example: Defrost/oil return
mode.
Running hours of the system.
Version information about the
system.
Possible units of measurement
▪ Dot
▪ Comma
▪ °C
▪ °F
▪ kWh
▪ MBtu
▪ l/min
▪ GPM
.
Example
Mon
15:20
Room
Mon
15:20
Room
EGSQH10S18AA9W
Daikin Altherma ground source heat pump
4P3517491 – 2013.06