Superior WRT4820WS Installation And Operation Instructions Manual

Epa wood-burning fireplaces

Advertisement

Quick Links

Shown with louver kit installed
THIS UNIT REQUIRES THE INSTALLATION OF A
FINISHING KIT. SEE "PARTS REQUIRED"
SECTION FOR DETAILS
Fireplace, Also For Use In
Manufactured Homes With Solid Fuel Only.
An French manual is available upon request. Order P/N 900092-00.
Ce manuel est disponible en francais, simplement en faire la demande. Numéro
de la pièce 900092-00.
• Hot! Do not touch! The glass and
surfaces of this appliance will be hot
during operation and will retain heat
for a while after shutting off the appli-
ance. Severe burns may result.
• Carefully supervise children in the
same room as appliance.
• If small children are present in the home, it is
recommended that this appliance be fitted with
an adjustable safety gate or barrier screen.
Shown with clean face kit installed
WARNING
Listed to standards:
ULC-S610 & UL-127
Report No. 3011202
EPA Cert. No. 537
INSTALLATION AND

OPERATION INSTRUCTIONS

WRT4820WS
EPA Wood-Burning Fireplaces
P/N 900091-00 REV. NC 12/2013
MODEL
WRT4820WS
This installation manual will enable you to obtain a safe, efficient and
dependable installation of your fireplace system. Please read and
understand these instructions before beginning your installation.
Do not alter or modify the fireplace or its components under any circum-
stances. Any modification or alteration of the fireplace system, including
but not limited to the fireplace, chimney components and accessories,
may void the warranty, listings and approvals of this system and could
result in an unsafe and potentially dangerous installation.
IHP wood-burning fireplaces are designed for use as a supplemental
heater. They are not intended for continuous use as a primary heat
source.
SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE
• The fireplace cannot be operated without a door
or firescreen. Consult your dealer to select the
correct door or firescreen.
• Important! To assure proper alignment of glass
doors: Install this fireplace in a square and
plumb condition, using shims as necessary at
sides and/or bottom.
• Install the fireplace only as described in these
instructions.
WARNING

Advertisement

Table of Contents
loading

Summary of Contents for Superior WRT4820WS

  • Page 1: Operation Instructions

    INSTALLATION AND OPERATION INSTRUCTIONS WRT4820WS EPA Wood-Burning Fireplaces P/N 900091-00 REV. NC 12/2013 MODEL WRT4820WS This installation manual will enable you to obtain a safe, efficient and dependable installation of your fireplace system. Please read and Shown with louver kit installed Shown with clean face kit installed understand these instructions before beginning your installation.
  • Page 2: Safety Rules And Specifications For Mobile Or Manufactured Home Installation

    IMPORTANT! GENERAL SAFETY WARNING WARNING PRECAUTIONS. READ AND UNDERSTAND THESE SAFETY Use care when selecting window Always ensure that the air inlet to RULES BEFORE YOUR FIRST FIRE. treatments for windows located the fireplace is free from debris near the fireplace. Avoid using and any other obstructions that combustible flowing window can block the entrance of air.
  • Page 3: Table Of Contents

    (required if using AC chimney) Installing The Finishing Kits ....Page 9 • The WRT4820WS fireplace is not intended for - AC chimney outside air kit Framing, Facing And Mantel ....Page 10 use with a gas log set. Do not use a fireplace - Gravity venting system Hearth Extension Requirements ..Page 10...
  • Page 4: Operating The Fireplace

    Primary Air and Air Boost Controls Fuel This will help cure the refractory bricks. During There is no flue damper in the WRT4820WS the first few fires of this appliance there may fireplace. As is common with air tight stoves, be some odor and smoke due to the curing of USE SOLID NATURAL WOOD FUEL ONLY.
  • Page 5: Refueling For Best Performance

    Your in this manner. Small dry pieces of softwood dealer can help you determine if you have The WRT4820WS fireplace will operate best if and construction scraps will burn very intensely properly seasoned wood for burning.
  • Page 6: Maintaining Your Wrt4820Ws Fireplace

    MAINTAINING YOUR WRT4820WS Top Baffle Removal Prior to Cleaning The Dealing With a Chimney Fire FIREPLACE Chimney Regular chimney maintenance and inspection Before starting to clean your chimney, we can prevent chimney fires. If you have a chimney Creosote - Formation and Need for Removal...
  • Page 7: Refractory Installation

    WARNING If the fit is still not perfect, you can adjust the door using the hinge screws. • Use only a IHP glass doors, specifically designed for the WRT4820WS DOOR ADJUSTMENT fireplace. The door may need to be adjusted to be com- •...
  • Page 8: Glass Care - Replacement

    Glass Replacement cutting floor or roof joists (see fireplace dimen- and lay it on a clean unabrasive surface. To The glass used for the WRT4820WS fireplace sions Page 11). replace the gasket, first remove all of the old is a high temperature ceramic glass (1,400° F / gasket and gasket cement.
  • Page 9: Installing The Finishing Kits

    The WRT4820WS requires the installation of a The part will be fixed in place when installing ANY OTHER INSTALLATION MAY RESULT finishing kit.
  • Page 10: Framing, Facing And Mantel

    Cover the insulation with Drywall panels around the fireplace. Hearth Extension Requirements 12” Max. The WRT4820WS fireplace may be installed (305mm) directly on a combustible floor. The supplied safety metal strip must be positioned as follows: Mantel...
  • Page 11: Fireplace And Framing Dimensions

    Corner Installation Back Wall of Chase/Enclosure Combustion OUTSIDE CHASE Including Finising Materials if any Air Kit 21-1/2” 20-3/8” Rough Framing Face (Unfinished Shown) * Zero Clearance From Back Spacer to Wall FRAMING DIMENSIONS 36-1/4” 921 mm Combustible materials can NOT be used in the space 2”...
  • Page 12: Insulated Chase Construction

    Insulate Joists Insulated Chase Construction Same As Ceiling Storm Collar Roof Support Flashing Draft Stops Attic Radiation Shield Floor Ceiling Firestop NOTE: It is recommended that the chase Wall walls and floor be insulated in the same CTDT manner, using the same insulation, as Termination the rest of the building, below the attic.
  • Page 13: Facing / Mantel

    Facing Non-Combustible Facing Fireplace Frame Section (Top View) The facing installation method depends on your Drywall finishing kit choice. 2” X 3” Min. 1. Facing with the louver kit - The 2x3 framing (51mm x 76mm) must offset to the back by a distance equiva- Spacer lent to the thickness of your facing material Rockboard...
  • Page 14: Hot Air Ducting Installation

    Maximum length See Figures 20 and 21 * The height of the louver must be measured 45” Min. from the base of the WRT4820WS fireplace to (1143mm) the middle point of the louver. To extend the double outlet system forward...
  • Page 15: Central Forced Air Kit

    The knock-outs provided on the back and on 1. Remove the plates closing up the 8” dia. collars (Figure 24). the sides of the WRT4820WS fireplace allow holes on top of the fireplace. Then, cut F) Fix the back draft damper to the fan outlet.
  • Page 16: Outside Air Kit

    OUTSIDE AIR KIT - REQUIRED (Included w/fireplace) OUTSIDE CONNECTION During operation, the fireplace requires fresh air for combustion and draws air out of the house. It may starve other fuel burning appliances such as gas or oil furnaces. As well, exhaust blowers may compete for Aluminum Tape air, causing negative pressure in the house, resulting in smoke entering Outside...
  • Page 17: Chimney System

    AC chimney enclosed in an insulated chase. 9. Cut and frame square holes in all floors, ceilings, and roof that the 2. The fireplace model WRT4820WS may be installed only with Security chimney will go through to provide a 2” (50 mm) clearance between Chimneys International Ltd 6”...
  • Page 18: Chimney Installation Instructions

    CHIMNEY INSTALLATION INSTRUC- Attic Radiation Shield TIONS Attic Radiation ASHT / S2100 Shield 1. Cut and frame the holes in the ceiling, floor HT6103+ / HT6000+ Solid Packed Pipe * Flashing and roof where the chimney will pass (see Figure 28). Use a plumb-bob to line up the center of the holes.
  • Page 19: Offset Chimney Installation

    If penetrating a wall, use Minimum Chimney Height Using Elbows a wall radiation shield. Fireplace Model WRT4820WS 3. Use another elbow to turn the chimney Chimney Model ASHT / S2100+ / HT6103+ / HT6000+ / AC vertically. Lock it to the chimney. Fasten...
  • Page 20 Offset Dimensions Total Height Horizontal Offset Chimney Elbow Offset & One Length Between Elbows Two Lengths Between Elbows 6” Height 8” 12” 18” 24” 36” 48” 8” & 48” 12” & 48” 18” & 48” 24” & 48” 36” & 48” 48”...
  • Page 21: Angled Wall Radiation Shield

    ANGLED WALL RADIATION SHIELD (RSM+ and RSMI30) When traversing a combustible wall with the chimney at a 30º or 45º angle, an angled firestop or wall radiation shield must be installed. Only one is required. NOTE: 45º angle for Canada only ( RSMI45 Support ACRS...
  • Page 22: Chimney Support Installation

    CHIMNEY SUPPORT INSTALLATION Universal Roof Support 18” (460 mm) 18” (460 mm) When installing a support, slightly lift the chimney system so the weight will lie on the support, not on the fireplace to reduce expansion noises. This support has three possible uses: 1.
  • Page 23: Masonry Application Instructions

    INSTALLATION INSTRUCTIONS FOR MASONRY APPLICATION Follow these steps: 1- Position the fireplace in its location. Temporarily install the ASHT WARNING: Before starting the installation, the masonry chimney must elbow on the top of the fireplace and, using a level, mark with an oval be inspected by a qualified chimney sweep.
  • Page 24: Installation Accessories

    OPTIONAL INSTALLATION ACCESSORIES Installation Accessories Fireplace Kits Description Cat./Part No. Description Cat./Part No. Blower Motor Speed Control (wall mount), VRUW VRUW Finishing Kits (Required - Order Separately) Rigid Firescreen BUCFZN Louver kit LOUVRECF Central Forced Air Kit Accessories Central Forced Air Kit, Central forced air kit including: blower Clean face kit CAPPINGCF (BISZY), flex adaptor (BISAF), 2 clamps, variable speed...
  • Page 25: Replacement Parts

    REPLACEMENT PARTS - WRT4820WS SPECIFICATIONS WRT4820WS Cat. No. Model Item # Description Cat./Part No. BISULTIMACF WRT4820WS Baffle refractory (2 pieces) PR-ISO2205 Back refractory PR-SR2996 Product Reference Information Right side refractory PR-SR2997D Weight 385 lbs Left side refractory PR-SR2997G Height 36”...
  • Page 26 REPLACEMENT PARTS - WRT4820WS NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
  • Page 27: Chimney Components Lists

    2125 Monterey, Laval, Quebec 1-800-361-4909 (USA) Canada, H7L 3T6 1-800-667-3387 (Canada) www.securitychimneys.com Fireplace Model WRT4820WS - Approved Venting Components manu- Secure Temp ASHT 1” High Temp. Insulated Stainless Steel Chimney ® factured by Security Chimneys International™ only. 6” I.D and 8” O.D., Double-Wall Stainl. Steel, Listed to CAN/UCL-S604 and UL-103HT Description Part/Cat.
  • Page 28 SECURITY CHIMNEYS™ - PARTS AND COMPONENTS LISTS The components listed below must be ordered from Security Chimneys International™. Contact your Security Chimneys Distributor or Dealer for ordering information. Security Chimneys International Limited 450-973-9999 Tubinox™ LL Chimney Lining System 2125 Monterey, Laval, Quebec 1-800-361-4909 (USA) Rigid Stainless Steel Liner For Relining A Masonry Chimney, 6”...
  • Page 29: Warranty

    THE WARRANTY Innovative Hearth Products ("IHP") 20 Year Limited Warranty warrants your Superior™ Brand wood burning fireplace ("Product") to be free from defects in materials and workmanship at the time of manufacture. The Product body, firebox and ceramic glass carry the 20 Year Limited Warranty. Ceramic glass carries the 20 Year Limited War- ranty against thermal breakage only.
  • Page 30: Product Reference Information

    WARRANTY Normally, all parts should be ordered through your IHP distributor or dealer. Parts will be shipped at prevailing prices at time of order. Your fireplace is covered by a limited warranty. Please read the warranty When ordering repair parts, always give the following information: to be familiar with its coverage.

Table of Contents