Operating Procedure; Setting The Speakers - JVC RX-F10S Instructions Manual

Operating procedure

1
On the front panel ONLY:
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
Ex.: When setting DIGITAL IN 1 terminal.
1
Press SETTING.
MULTI JOG now works for the setting operation.
2
Turn MULTI JOG until the item you want to set
appears on the display.
• As you turn MULTI JOG, the setting items change as
follows:
EQ C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST
LPCM L C R PL
DOLBY D NEO : 6
S . WFR LFE
DTS AAC DSP 3D
LS SB RS
96 / 24 AUTO SR
SUBWOOFER
CENTER SPK
S BACK SPK
FRNT L DIST
CENTER DIST
SURR R DIST
SUBWFR OUT
DUAL MONO
LFE ATT
DIGITAL IN1
DIGITAL IN3
AUTO MODE
3
Press SET.
The current setting of the selected item appears.
EQ C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST
PL
LPCM L C R
DOLBY D NEO : 6
S . WFR LFE
DTS AAC DSP 3D
LS SB RS
96 / 24 AUTO SR
4
Turn MULTI JOG to select the appropriate
setting.
EQ C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST
PL
LPCM L C R
DOLBY D NEO : 6
S . WFR LFE
DSP 3D
DTS AAC
LS SB RS
96 / 24 AUTO SR
DVR/DVD
TV
Your setting is stored.
5
Press SET.
6
Repeat steps 2 to 5 to set other items if
necessary.
18
3, 5 2, 4
AUTO MUTING SLEEP AUTO MODE
ATT
HP
MHz
kHz
FRONT SPK
SURRND SPK
DIST UNIT
FRNT R DIST
SURR L DIST
S BACK DIST
EX/ES
CROSS OVER
MIDNIGHT M.
DIGITAL IN2
AUTO SURRND
(Back to the beginning)
AUTO MUTING SLEEP AUTO MODE
ATT
HP
MHz
kHz
AUTO MUTING SLEEP AUTO MODE
ATT
HP
MHz
kHz
VIDEO
VCR

Setting the speakers

Setting subwoofer information—SUBWOOFER
Each time the receiver turns on, the receiver detects the
subwoofer connection and automatically changes the setting of
the subwoofer.
When you want to change the setting manually, select either one
below.
SUBWFR :YES Select when you have connected a subwoofer.
The subwoofer indicator (
display. You can adjust the subwoofer output level
(see page 23).
SUBWFR : NO Select when you have disconnected a subwoofer.
Selecting this changes the front speaker size to
"LRG" (see below).
NOTE
You need to change the setting each time turning on the receiver
if you want to change the subwoofer information set automatically.
Setting the speaker size—FRONT SPK (front
speakers), CENTER SPK (center speaker), SURRND
SPK (surround speakers), S BACK SPK (surround
back speaker)
Register the sizes of all the connected speakers.
LRG (large) Select when the cone speaker size is larger than
12 cm.
SML (small) Select when the cone speaker size is smaller than
12 cm.
NO Select when you have disconnected a speaker.
(Not selectable for the front speakers.)
Initial setting: SML for all speakers*
* When "SUBWOOFER" is set to "SUBWFR : NO," the front
speaker size is fixed to "LRG" (and you cannot select "SML").
NOTES
• If you have selected "SML (small)" for the front speaker size,
you cannot select "LRG (large)" for other speakers.
• When "SURRND SPK" is set to "SML (small)," you cannot select
"LRG (large)" for the surround back speaker.
• When "SURRND SPK" is set to "NO," the surround back
speaker is fixed to "NO."
• If you change one of the speaker size either from "NO" to "SML"
or "LRG," or from "SML" or "LRG" to "NO," the distance and
output level set manually will be applied instead of those set by
using Smart Surround Setup.
) lights up on the
S . WFR