Boost Function; Advance Function (In Auto Mode Only); Display Lock Function; Power Failure - Stanley BRANDON 60K User Manual

4. When the time has elapsed, the acoustic signal
will sound for 60 seconds and the word Alarm
flashes. It can be cancelled by pressing the
Alarm button.
Note: This timer operates only when the oven is set
to "manual" mode.

BOOST FUNCTION

By pressing the "BOOST" button, boost will be
displayed and the symbols for central heating and
hot water will flash. Then pressing either the "Hot
Water", "Central Heating" or "Pre Heat" buttons will
turn this mode on for 1 hour. The symbols will flash
for 10 seconds and if neither of the 3 options are
selected then the display will revert to current time
and day. If a mode is selected the symbol for this
mode and the word "BOOST" will remain displayed
for 1 hour, providing none of the oven control
functions on the clock are used within this hour.
Boost can be cancelled by pressing the relevant
function button, i.e.

ADVANCE FUNCTION (IN AUTO MODE ONLY)

By pressing the "ADV" button, ADVANCE will be
displayed and the symbols for central heating and
hot water will flash. Then pressing either the "Hot
Water" or "Central Heating" or "Pre-heat" buttons
will bring forward the next switching time for that
mode. The symbols will flash for 10 seconds within
which one of the 3 options must be selected before
the display will revert to current time and day.
Advance can be cancelled by pressing the relevant
function button, i.e.
Note: Advance function is only applicable when
timer is in 'Auto Mode'.
The DHW , Heating and oven Pre-heat programs
can be turned OFF by de-selecting AUTO, so that
no lights are visible.
The DHW and Heating can also be set to
continuous ON by pressing the button so that the
ON light illuminates.

DISPLAY LOCK FUNCTION

By pressing and holding the "LOCK" Button for 10
seconds the display will become locked, and
LOCKED will be displayed. To unlock the display
press and hold the "LOCK" button for 10 seconds. If
any button is pressed while the display is locked the
Fig 7
word "LOCKED" will flash on the display.

POWER FAILURE

Your clock has a built-in battery to ensure correct
operation after a mains supply power cut. No action
should be necessary following a power loss.
Diagnostics
If an error occurs in the appliance the electronics will
detect it and narrow down the problem area.
Code no 1.
Code no 2.
Code no 3.
Code no 4.
Code no 5.
Code no 6.
Code no 8.
Code no 9
When an error occurs it can be reset by pressing the
" " button for 5 seconds, the code no. on the display
will disappear, if the error is still present the code no.
will reappear, it will be necessary to call the Stanley
service centre.
In the special case of a no. 9 code this could be due
to all radiator valves being turned off. It is a
requirement that at least 1 radiator in zone 1 is
permanently on.
If Code 4 or 5 appear on the display screen prior to
the fault being cleared using the F button, it will
require the high limit swiches to be reset, to access
and reset the high limit switches take the following
steps:
1. Remove plinth at base of cooker, the high limit
switches are located in the centre of the base
plate, see Fig.8.
2. Press the LH & RH buttons to reset the High Limit
reset switches, then press the F button for 5
seconds to clear the fault on the display screen.
However, if the high limit does not reset it may be
due to the appliance being excessively hot, wait until
the appliance has cooled and press the high limit
switches again, if they do not reset when appliance
is cool, please contact your local service engineer.
8
Oven thermocouple failure
Boiler thermistor failure
Flue thermistor failure (Gas only)
Boiler high limit switch opened
Oven high limit switch opened
Flue thermistor over temperature
(Gas only)
Oven burner faulty
Boiler Excess Temperature