Circuit Open/Short Inspection; Pressure Regulator Inspection - Mazda CX-7 2007 Workshop Manual

Circuit Open/Short Inspection

1. Disconnect the PCM connector. (See01-40-6 PCM REMOVAL/INSTALLATION[L3 WITH TC].)
2. Inspect the following wiring harnesses for an
open or short circuit (continuity check).
2BE 2BA 2AW 2AS 2AO 2AK 2AG 2AC 2Y 2U 2Q 2M
2BF 2BB 2AX 2AT 2AP 2AL 2AH 2AD 2Z 2V 2R 2N
2BG 2BC 2AY 2AU 2AQ 2AM 2AI 2AE 2AA 2W 2S 2O
2BH 2BD 2AZ 2AV 2AR 2AN 2AJ 2AF 2AB 2X 2T 2P
Open circuit
• If there is no continuity, there is an open circuit. Repair or replace the wiring harness.
— No.1 cylinder fuel injector terminal A and PCM terminal 2BB
— No.2 cylinder fuel injector terminal A and PCM terminal 2BC
— No.3 cylinder fuel injector terminal A and PCM terminal 2BD
— No.4 cylinder fuel injector terminal A and PCM terminal 2AZ
— No.1 cylinder fuel injector terminal B and PCM terminal 2BG
— No.2 cylinder fuel injector terminal B and PCM terminal 2BH
— No.3 cylinder fuel injector terminal B and PCM terminal 2BH
— No.4 cylinder fuel injector terminal B and PCM terminal 2BG
Short circuit
• If there is continuity, there is a short circuit. Repair or replace the wiring harness.
— No.1 cylinder fuel injector terminal A and power supply
— No.1 cylinder fuel injector terminal A and body ground
— No.2 cylinder fuel injector terminal A and power supply
— No.2 cylinder fuel injector terminal A and body ground
— No.3 cylinder fuel injector terminal A and power supply
— No.3 cylinder fuel injector terminal A and body ground
— No.4 cylinder fuel injector terminal A and power supply
— No.4 cylinder fuel injector terminal A and body ground
— No.1 cylinder fuel injector terminal B and power supply
— No.1 cylinder fuel injector terminal B and body ground
— No.2 cylinder fuel injector terminal B and power supply
— No.2 cylinder fuel injector terminal B and body ground
— No.3 cylinder fuel injector terminal B and power supply
— No.3 cylinder fuel injector terminal B and body ground
— No.4 cylinder fuel injector terminal B and power supply
— No.4 cylinder fuel injector terminal B and body ground
End Of Sie
PRESSURE REGULATOR INSPECTION[L3 WITH TC] WM: PRESSURE REGULATOR
Note
• Due to the adoption of the mechanical returnless fuel system, the pressure regulator cannot be inspected
separately.
1. Perform "FUEL LINE PRESSURE INSPECTION". (See 01-14-5 FUEL LINE PRESSURE INSPECTION[L3
WITH TC].)
End Of Sie
01-14–28
FUEL SYSTEM [L3 WITH TC]
PCM
WIRING HARNESS-SIDE CONNECTOR
2E 2A 1BE 1BA 1AW 1AS 1AO 1AK 1AG 1AC 1Y 1U 1Q 1M
2I
2J 2F 2B 1BF 1BB 1AX 1AT 1AP 1AL 1AH 1AD 1Z 1V 1R 1N
2K 2G 2C 1BG 1BC 1AY 1AU 1AQ 1AM 1AI 1AE 1AA 1W 1S 1O
2L 2H 2D 1BH 1BD 1AZ 1AV 1AR 1AN 1AJ 1AF 1AB 1X
FUEL INJECTOR
WIRING HARNESS SIDE CONNECTOR
A B
1T 1P
acxuuw00000039
1I 1E 1A
1J 1F 1B
1K 1G 1C
1L 1H 1D
acxuuw00000040
id011439800800