Bluetooth hands-free kit retrofit for bmw x5 (e53) 2001; bmw x5 (e53) 2002; bmw x5 (e53) 2003; bmw x5 (e53) 2004; bmw x5 (e53) 2005; bmw x5 (e53) 2006; bmw x5 (e53) 2007; bmw x5 (e53) 2008; bmw x5 (e53) 2009; bmw x5 (e53) 2010; bmw x5 (e53) 2011; bmw x5 ( (19 pages)
Retrofit bmw accessory menu acm for bmw 1 series (e81, e82, e87) bmw 3 series (e90, e91, e92, e93) bmw 5 series (e60, e61) bmw 6 series (e63, e64) bmw x5 (e70) bmw x6 (e71) (42 pages)
Siemens hands-free facility retrofit kit with speech input for bmw 3 series saloon (e36/4) lhd, bmw 3 series coupe (e36/2) lhd, bmw 3 series touring (e36/3) lhd, bmw 3 series convertible (e36/c) lhd, bmw 3 series compact (e36/5) lhd (21 pages)
The installation time for this kit is approximately 1.25 hour These instructions were developed especially for BMW vehicles and are not to be compared to any existing instructions for vehicles other than BMW. No methods other than those specified in this...
Page 2
84 11 0 302 643 Owner’s Manual For Voice Input System 84 11 0 027 942 PROCEDURE: To install and connect the BMW Universal Bluetooth Hands-Free System Disconnect Battery prior to starting the installation. A. Bluetooth Antenna & Pairing Button Installation 1.
Page 3
3. Remove the center console storage tray (2), refer to RA 51 16 200. The center console will need to be removed in order to install the pairing button later in the procedure. 4. Locate the black FAKRA connector (1), located below the rear ashtray assembly.
Page 4
8. In order to install the Pairing Button, P/N 84 13 0 302 715, an opening must be cut into the rear of the center console. The area to be cut out can be marked using the template P/N 84 11 0 304 482 9.
Page 5
17. Carefully reinstall the center console. 18. Reinstall the top panel (1) and reinstall the two Phillips head screws (3) making certain that they go all the way down through the antenna- mounting bracket to the clip nuts. 19. Locate the black 18-pin connector X4545 in bundle (1).
Page 6
23. Insert the Pairing Button, P/N 84 13 0 302 715, into the cutout and reinstall the cupholders and coin tray. B. ULF Control Module Installation 1. Remove/ peel off the Bluetooth Passkey sticker (2) from the label on the ULF Control Module (1). 2.
Page 7
E46 Touring 1. Attach the ULF Control Module (F) to the mounting bracket (G), P/N 84 13 6 924 698; use three M5 hex nuts (J), P/N 61 21 1 371 401. 2. Locate the black 54-pin connector and white FAKRA connector, bundled near the left rear wheel hub.
Page 8
4. Prior to connecting the black 54-pin connector to the ULF Control Module pins 7 & 8 will need to be removed from the connector and tied back. Note: Pins 7& 8 provide a wheel speed input signal that is not utilized by the ULF Control Module and need to be disconnected from the control module.
Page 9
11. Insert the ULF Control Module and bracket (1) into the opening in the inner area of the rear quarter panel, and place the bracket against the inner portion of the support structure. 12. The three threaded lugs on the mounting bracket should be inserted through the three holes in the support structure (2).
Page 10
E46 Sedan with Carrier Rack 1. If the left rear of the trunk is as shown, then a component carrier rack is already installed and the following steps should be followed. 2. If the trunk is not as shown refer to the installation steps for no carrier rack installed, on page 12.
Page 11
8. Locate pins 7 & 8 (2) and carefully remove them from the terminal housing (1). 9. Bend the wires for pin 7 & 8 back away from the connector 10. Wrap each terminal separately with electrical tape and tape them to the wiring harness. 11.
Page 12
FAKRA connector (1) to the ULF Control Module (F) after the bracket is installed. 15. Reinstall the left rear trim panel. E46 Sedan With No Carrier Rack IMPORTANT: In the event a vehicle is not equipped with a carrier bracket the trunk will look as indicated in the illustration.
Page 13
7. For E46 vehicles produced prior to 8/02 continue with step 14. 8. For E46 vehicle produced as of 8/02 only: Prior to connecting the black 54-pin connector to the ULF control Module pins 7 & 8 will need to be removed from the connector and tied back (Pin 7 &...
Page 14
11. Bend the wires for pin 7 & 8 back away from the connector 12. Wrap each terminal separately with electrical tape and tape them to the wiring harness. 13. Reassemble the connector. 14. Locate the black 54-pin connector and white FAKRA connector.
Page 15
C. Installation of Voice Input Jumper 1. If a Voice Input Jumper Plug is not installed then a Jumper Plug, P/N 84 11 0 018 038, must be obtained and installed for the system to function correctly. The jumper plug should be installed onto a blue 26 pin connector that is located near the black 54 pin connector for the ULF module.
Page 16
Follow the on screen requests to activate the coding procedure. E. Function test Upon completion of the recoding, verify that the BMW Universal Bluetooth Hands-Free System is working correctly by going through the following action steps. After completing each step ensure that...
ULF Control Module to Vehicle) E46 Only: Remove pin 7 & 8 from the 54-pin connector After installation of ULF system the speedometer going to the ULF Control Module. Refer to the and odometer do not work. E46 installation instructions.
Page 18
G. Pairing Procedure: The pairing procedure that must be initiated through the phone will differ corresponding to the different menu configurations of the various Bluetooth mobile phones on the market. The user’s manual of the phone should always be referenced for specific steps on how to activate the Bluetooth feature and to pair/link devices.
Page 19
10. Enter password (= ULF passkey) located on ULF Control Module in the rear of the vehicle or on the Passkey Reference Card. • Mobile Phone display shows ‘BMW …… Pairing’ • Mobile Phone display shows ‘Pairing Successful’ • Board Monitor display shows ‘Pairing succeeded’ for 3 seconds 11.
Page 20
COMPONENT LOCATION: SPORT WAGON SEDAN A - Eject Box C/E - Microphone D - Bluetooth Antenna F - ULF Control Module...
Page 21
ULF Wiring Schematic for the E46 with Boardmonitor Light Switch input Bluetooth Antenna X4545 X9988 X10015 X10016 Interface Switch not in use X4545 X13016 X9987 X01185 Control Module X01185 X10390 Jumper Plug to other modules from terminal 30 from terminal R...
Page 22
ULF Wiring Schematic for the E46 without Boardmonitor Bluetooth Light Antenna Switch input X9988 X10015 X10016 X4545 Interface Switch not in use X4545 X13016 X9987 X01185 Control Module X01185 X10390 Jumper Plug to other modules Light Switch from terminal 30...