Ford 2001 Explorer SportTrac User Manual

2001 explorer sporttrac

page of 265

/ 265
Contents
Table of Contents
Bookmarks

Table of Contents

Quick Links

2001 Explorer SportTrac

Before driving

Introduction

Instrumentation

Controls And Features

Seating And Safety Restraints

Starting and driving

Starting

Driving

Roadside Emergencies

Servicing

Maintenance And Care

Capacities And Specifications

Customer Assistance

Reporting Safety Defects

Index

photocopying, recording or by any information storage and retrieval system or translation

in whole or part is not permitted without written authorization from Ford Motor Company.

Ford may change the contents without notice and without incurring obligation.

Contents

127

132

158

182

233

241

253

254

Table of Contents

Summary of Contents for Ford 2001 Explorer SportTrac

Page 1 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Ford may change the contents without notice and without incurring obligation.
Page 2: Introduction
Introduction The following warning may be required by California law: CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Page 3 Using your vehicle as an ambulance Do not use this vehicle as an ambulance. Your vehicle is not equipped with the Ford Ambulance Preparation Package. Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate than other types of vehicles.
Page 4 Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation Child Seat Tether Warning Anchorage Brake System Anti-Lock Brake System Brake Fluid - Traction Control...
Page 5 Introduction Vehicle Symbol Glossary Interior Luggage Child Safety Door Compartment Release Lock/Unlock Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, Battery Acid or Sparks Explosive Gas Fan Warning Maintain Correct Fluid Power Steering Fluid Level Emission System...
Page 6: Instrumentation
Instrumentation Instrument cluster (pg. 8) Gearshift (includes overdrive button) (pg. 137) Speed controls* (pg. 56) Panel dimmer control (pg. 19) Headlamp control (pg. 18) CHECK 60 70 GAGE 0 0 0 RPMx1000 SPEED 0 0 0 0 0 0 CONT CHECK ENGINE FUEL DOOR...
Page 7 Instrumentation Audio system (pg. 27) 4wd control* Power down rear window (pg. 143) (pg. 24) SCAN TUNE SEEK SHUF MUTE LOAD BASS TREB FADE PUSH ON MENU Foglamp control* (pg. 18) Climate controls (pg. 20)
Page 8 Instrumentation WARNING LIGHTS AND CHIMES DOOR AJAR CHECK GAGE RPMx1000 SPEED CHECK CONT ENGINE HIGH CHECK km/h FUEL R N D 2 1 THEFT BRAKE Check engine Your vehicle is equipped with a computer that monitors the engine’s CHECK emission control system. This ENGINE system is commonly known as the On Board Diagnostics System...
Page 9 Instrumentation 3. The fuel cap may not have been properly installed and securely tightened. These temporary malfunctions can be corrected by filling the fuel tank with high quality fuel of the recommended octane and/or properly installing and securely tightening the gas cap. After three driving cycles without these or any other temporary malfunctions present, the Check Engine light should turn off.
Page 10 Instrumentation Air bag readiness Momentarily illuminates when the ignition is turned ON. If the light fails to illuminate, continues to flash or remains on, have the system serviced immediately. Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts.
Page 11 Instrumentation Turn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the indicators stay on continuously or flash faster, check for a burned-out turn signal bulb. Refer to Bulbs in the Maintenance and care chapter. High beams Illuminates when the high beam headlamps are turned on.
Page 12 Instrumentation Four wheel drive low (if equipped) Momentarily illuminates after the engine is STARTED. Illuminates when four-wheel drive low is engaged. If the light continues to flash have the system serviced. Four wheel drive high (if equipped) Momentarily illuminates after the vehicle has been STARTED.
Page 13 Instrumentation Speed control This light comes on when either the SPEED SET/ACCEL or RESUME controls CONT are pressed. It turns off when the speed control OFF control is pressed, the brake or clutch (if equipped) is applied or the ignition is turned to the OFF position.
Page 14 Instrumentation GAUGES DOOR AJAR CHECK GAGE RPMx1000 SPEED CHECK CONT ENGINE HIGH CHECK km/h FUEL R N D 2 1 THEFT BRAKE Speedometer Indicates the current vehicle speed. km/h...
Page 15 Instrumentation Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool.
Page 16 Instrumentation Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer RPMx1000 pointer continuously at the top of the scale may damage the engine. Battery voltage gauge This shows the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range (as indicated by arrows), have the...
Page 17 Instrumentation Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion. The ignition should be in the OFF position while the vehicle is being refueled.
Page 18: Controls And Features
Controls and features HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. Foglamp control (if equipped) The foglamps can be turned on when the headlamp control is in either of the following positions: •...
Page 19 Controls and features High beams • Push forward to activate. • Pull toward you to deactivate. Flash to pass Pull toward you to activate and release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation.
Page 20 Controls and features CLIMATE CONTROL SYSTEM Manual heating and air conditioning system (if equipped) Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle.
Page 21 Controls and features • A/C-Uses outside air to cool the vehicle. It is quieter than MAX A/C but not as economical. Airflow will be from the instrument panel registers. • (Panel)-Distributes outside air through the instrument panel registers. However, the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode.
Page 22 Controls and features • To reduce humidity buildup inside the vehicle in cold weather conditions, don’t drive with the climate control system in the OFF or MAX A/C position. • To reduce humidity buildup inside the vehicle in warm weather conditions, don’t drive with the climate control system in the OFF position.
Page 23 Controls and features To aid in side defogging/demisting in cold weather. 1. Select 2. Set the temperature control to full heat 3. Set the fan speed to HI 4. Direct the outer panel vents towards to side windows To increase airflow to the outer panel vents, close the central panel vents.
Page 24 Controls and features Select for air to flow through these vents: – VOLUME BAND SEEK MEMORY Select for air to flow through these vents: – VOLUME BAND SEEK MEMORY POWER DOWN BACK WINDOW To operate the power down back window, the ignition switch must be in the Run or Accessory position.
Page 25 Controls and features All rear seat occupants and/or cargo must be properly restrained and clear of the back window opening before operating the power down rear window. Turn control counter-clockwise and release to lower window all the way to the full open position. Turn control clockwise and release to raise the window all the way to the full closed position.
Page 26 Controls and features Normal Operation If an “up” command is selected and the ignition is switched to OFF or START during window travel, the window will: 1. stop if it is between the vent position and fully closed or 2. continue to move up to the vent position if it is between vent and fully open.
Page 27: Using Your Audio System
Controls and features 4WD CONTROL (IF EQUIPPED) This control operates the 4WD. Refer to the Driving chapter for HIGH more information. USING YOUR AUDIO SYSTEM Premium AM/FM Stereo/Cassette/Single CD DISC VOL PUSH ON FM 1 MUTE TAPE DOLBY B NR AUTO SEEK TUNE...
Page 28 Controls and features Volume/power control Press the control to turn the audio VOL - PUSH ON system on or off. Audio power can also be turned on by pressing the AM/FM select control or the tape/CD select control. Audio power is turned off by using the volume/power control.
Page 29 Controls and features Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly. • Press to move to the next frequency up the band (whether or not a listenable station is located there).
Page 30 Controls and features Scan function The scan function works in radio, SCAN tape or CD mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the control again to stop the scan mode. Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape.
Page 31 Controls and features Autoset memory preset Autoset allows you to set strong radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Starting autoset memory preset 1.
Page 32 Controls and features Treble adjust The treble adjust control allows you BASS TREB to increase or decrease the audio system’s treble output. Press the TREB control then press: • to decrease the treble output • to increase the treble output. Speaker balance adjust Speaker sound distribution can be FADE...
Page 33 Controls and features Speaker fade adjust Speaker sound can be adjusted FADE between the front and rear speakers. Press the FADE control then press: • to shift the sound to the front and • to shift the sound to the rear. Tape/CD select •...
Page 34 Controls and features Fast forward The fast forward control works in tape and CD modes. • In the tape mode, tape direction will automatically reverse when the end of the tape is reached. • In CD mode, pressing the control fast forwards the CD within the current track.
Page 35 Controls and features Compression adjust Compression adjust brings soft and COMP loud CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust. Shuffle feature The shuffle feature operates in CD SHUFFLE mode (if equipped) and plays all tracks on the current disc in random order.
Page 36 Controls and features • to decrease minutes and • to increase minutes. If your vehicle has a separate clock, (other than the digital radio display), the CLK control will not function in the above manner. The CLK control will allow you to switch between media display mode AUTO (radio station, stereo information,...
Page 37 Controls and features AM/FM Stereo In Dash Six CD Radio for Pioneer Sound System DISC SHUF SCAN SEEK TUNE MUTE LOAD BASS PUSH ON TREB FADE MENU Volume/power control Press the control to turn the audio system on or off. PUSH ON Turn the control to raise or lower volume.
Page 38 Controls and features AM/FM select The AM/FM select control works in radio and CD modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in CD mode Press this control to stop CD play and begin radio play.
Page 39 Controls and features Seek function The seek function works in radio or CD mode. Seek function in radio mode • Press to find the next listenable station down the frequency band. SEEK DOWN will display. • Press to find the next listenable station up the frequency band. SEEK UP will display.
Page 40 Controls and features Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2). Setting memory preset stations 1.
Page 41 Controls and features Starting autostore 1. Press and momentarily hold the AM/FM control. 2. AUTOSET will flash in the display as the frequency band is scrolled through. 3. When the six strongest stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available.
Page 42 Controls and features Display description Six circles are always lit in the digital display. These signify the six CD slots in the audio system. When a disc is loaded into a particular slot (1–6), the number inside that specific circle lights. If the circle is empty, there is no CD in that particular slot.
Page 43 Controls and features Eject Press the EJ control to stop and eject a CD. You can choose which CD will be ejected by pressing the EJ control and the desired preset number (1–6). For example, to eject CD 2, press the EJ control and then press the preset 2 control.
Page 44 Controls and features Fast forward The fast forward control works in CD modes. Press and hold the FF control until the desired selection is reached. If the end of the disc is reached, the CD will return to the first track on the first disc.
Page 45 Controls and features Bass adjust The bass adjust control allows you BASS to increase or decrease the audio system’s bass output. TREB Press the BASS control. Use the SEL control to increase or decrease the amount of bass. Treble adjust The treble adjust control allows you BASS to increase or decrease the audio...
Page 46 Controls and features Menu mode The MENU control allows you to MENU access many different features within your audio system. There are three sets of menus available depending upon which mode or feature is activated. While in FM mode, two menus are available.
Page 47 Controls and features Traffic announcements This feature allows you to hear traffic announcements. When in this MENU mode, traffic announcements will interrupt radio and CD play. When in FM mode and RDS is activated, press the MENU until TRAFFIC OFF displays. Press the SEL control to engage the feature.
Page 48 Controls and features Radio data system (RDS) feature This feature allows your audio system to receive text information MENU from RDS-equipped FM radio stations. To activate RDS: • When in FM mode, press the MENU control until RDS OFF displays. •...
Page 49 Controls and features Press the MENU control until FIND program type is displayed. MENU Use the SEL control to select the program type. With the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: •...
Page 50 Controls and features Press the DSP control to access the DSP menu. Press the SEL control to enter one of the following modes: • DSP OFF • SIGNAL MODE • OCCUPANCY MODE Use the SEL control to select the desired signal mode (the selected mode will appear in the display).
Page 51 Controls and features Use the SEL control to manually set the time. • Press to increase hours/minutes. • Press to decrease hours/minutes. Press the MENU control again to disengage the clock mode. Rear seat controls (if equipped) The rear seat controls allow the middle seat passengers to operate - VOLUME + MODE...
Page 52 Controls and features Adjusting the volume Press the + control to increase - VOLUME + volume. MODE Press the - control to decrease volume. SEEK MEMORY From the rear seat controls, volume control can be set no higher than the current radio setting unless the speakers are turned off. Refer to Turning speakers on and off.
Page 53 Controls and features Mode select Push the MODE control to toggle - VOLUME + between AM, FM1, FM2, tape, CD or MODE CD changer (if equipped). SEEK MEMORY Memory preset control Push the MEMORY control - VOLUME + successively to allow rear seat MODE passengers to scroll through the 6 memory presets in AM, FM1 or...
Page 54 Controls and features Cleaning compact discs Inspect all discs for contamination before playing. If necessary, clean discs only with an approved CD cleaner and wipe from the center out to the edge. Do not use circular motion. CD and CD changer care •...
Page 55 Controls and features Radio reception factors Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their strength/volume relative to other stations.
Page 56 Controls and features POSITIONS OF THE IGNITION 1. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. 3. OFF, shuts off the engine and all accessories without locking the steering wheel.
Page 57 Controls and features To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. To set a speed • Press SET ACC. For speed control to operate, the speed control must be ON and the vehicle speed must be greater...
Page 58 Controls and features To set a higher set speed • Press and hold SET ACC. Release the control when the desired vehicle speed is reached or • Press and release SET ACC to operate the Tap-Up function. Each press will increase the set speed by 1.6 km/h (1 mph) or COAST •...
Page 59 Controls and features To disengage speed control • Depress the brake pedal or • Depress the clutch pedal (if equipped). Disengaging the speed control will not erase the previously programmed set speed or engine RPM. Pressing OFF will erase the previously programmed set speed or engine RPM.
Page 60 Controls and features To return to a previously set speed • Press RSM. For RSM to operate, the vehicle speed must be faster than 48 km/h (30 mph). COAST Indicator light This light comes on when either the SPEED SET ACCEL or RES controls are CONT pressed.
Page 61 Controls and features TILT STEERING WHEEL (IF EQUIPPED) Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control to lock the steering wheel in position. Never adjust the steering wheel when the vehicle is moving.
Page 62 Controls and features Push (tap) the end of the stalk briefly for a single swipe (no wash). Push and hold for three swipes with wash. Push and hold for a longer wash (up to ten seconds). Speed dependent wipers When the windshield wiper control is set on the intermittent settings, speed-sensitive front wipers automatically adjust as the vehicle’s speed changes.
Page 63 Controls and features OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package. Storage compartment (if equipped) Press the OPEN control to open the storage compartment. The door will open slightly and can be moved to full open.
Page 64 Controls and features • Place the provided height adaptors onto the back of the GARAGE control as needed. • Press the GARAGE control to activate the transmitter. Moon roof (if equipped) You can move the glass panel of the moon roof back to open or tilt up to ventilate the vehicle.
Page 65 Controls and features Do not let children play with the moon roof. They may seriously hurt themselves. Electronic compass/temperature display (if equipped) Outside air temperature The outside temperature display is contained in the overhead console. OPEN The temperature display can be turned off and on by pressing the MODE control on the overhead console.
Page 66 Controls and features Compass zone adjustment 1. Determine which magnetic zone you are in by referring to the zone map. 2. Turn ignition to the ON position. 3. Press and hold the MODE control until VAR appears in the display, then release.
Page 67 Controls and features Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines: • Press and hold the MODE control until CAL appears in the display (approximately eight seconds) and release. • Drive the vehicle slowly (less than 5 km/h [3 mph]) in circles until CAL indicator turns off in about 2–3 complete circles.
Page 68 Controls and features POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. AUTO • Press the bottom portion of the rocker switch to open. AUTO One touch down •...
Page 69 Controls and features Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls except for the driver’s press the left side of the control. Press the right side to restore the window controls. POWER DOOR LOCKS Press control to unlock all doors.
Page 70 Controls and features Childproof door locks When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each LO C K E D...
Page 71 Controls and features 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to disable adjust function. Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash.
Page 72 Controls and features CENTER CONSOLE Your vehicle may be equipped with a variety of console features. These include: • Utility compartment with compact disc storage • Auxiliary power point • Cupholders • Ashcup • Removable utility bag (if equipped) • Writing surface with note pad •...
Page 73 Controls and features AUXILIARY POWER POINT The power point is an additional power source for electrical accessories. • With full console. • Without full console. Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty.
Page 74 Controls and features Lift the cover to access the auxiliary power point. POSITIVE RETENTION FLOOR MAT Position the floor mat so that the eyelets are over the pointed end of the retention posts and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal.
Page 75 Controls and features TAILGATE LOCK Your vehicle is equipped with a tailgate lock designed to prevent theft of the tailgate. • Insert ignition key and turn to the right to engage lock. • Turn ignition key to the left to unlock.
Page 76 Controls and features CARGO CAGE (IF EQUIPPED) Your vehicle may be equipped with a cargo cage designed to extend the pickup box for larger loads. To extend the cargo cage: 1. Lower tailgate. 2. Pull the round knobs on each side of the cargo cage to release it from the pickup box.
Page 77 Controls and features 4. Evenly push down on the cargo cage and push the round knobs in on each side locking it in place. To stow the cargo cage, follow steps one through four in reverse order. The cargo cage may be used to secure a load of up to 46 kg (100 lbs.) on the tailgate.
Page 78 Controls and features Activating Cargo Cage Thief Deterrent device: The following procedure can be done with the cargo cage in the stowed or extended position. 1. Locate the phillips head screw in the middle of the vertical brace on the locking clip. 2.
Page 79 Controls and features To remove the cargo cage: 1. Extend the cargo cage. 2. Pull the round knobs on each side of the cage to unlock it. Make sure the locking clip screws are loose before removing the cargo cage. 3.
Page 80 Controls and features TONNEAU COVER (IF EQUIPPED) The tonneau cover has been designed to maximize fuel economy and should be fully installed whenever possible. The rear panel can be folded in half and secured behind the cab, or the whole cover can be removed completely from the vehicle. To avoid damage to the cover, do not operate the vehicle unless the cover is fully installed, or securely stowed.
Page 81 Controls and features Do not drive with front panel unlocked or folded on top of the rear panel. To open the rear panel: • Open the lock cover and unlock the rear panel. • Lift the rear panel to access items in the pickup box. •...
Page 82 Controls and features To stow the rear panel: • Before driving with the rear panel open, unlock the rear panel. • Lift the rear panel up, lay it on top of the front panel and secure it with the two straps to the exterior tiedowns on the pickup box. Failure to secure the rear panel could damage the tonneau cover or vehicle.
Page 83 Controls and features To remove the tonneau cover: The tonneau cover weighs 29 kg (70 lbs.) and needs to be supported during removal since the panels will automatically lock when set down on the pickup box. This is a two person operation. •...
Page 84 Controls and features To open the tonneau cover from the inside, pull the “T” shaped handle and push up on the tonneau cover panel. The material that the handle is made of will glow for hours in the darkness of the pickup box following brief exposure to ambient light.
Page 85 Controls and features The remote entry features only operate with the ignition in the LOCK position. If there is any potential remote keyless entry problem with your vehicle, ensure ALL key fobs (remote entry transmitters) are brought to the dealership, to aid in troubleshooting. Unlocking the doors Press this control to unlock the driver’s door.
Page 86 Controls and features Sounding a panic alarm Press this control to activate the alarm. To deactivate the alarm, press the control again or turn the ignition to Panic alarm will only operate with the ignition in the OFF position. Replacing the battery The transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent.
Page 87 Controls and features Replacing lost transmitters If a remote transmitter has been lost and you would like to remove it from the vehicle’s memory, or you would like to purchase additional remote transmitters and have them programmed to your vehicle: •...
Page 88 Controls and features Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm. The system automatically turns off after 25 seconds or when the ignition is turned to the ON position. The dome lamp control (if equipped) must not be set to the OFF position for the illuminated entry system to operate.
Page 89 Controls and features The factory-set code is located: • on the owner’s wallet card in the glove compartment • marked on the computer module When pressing the controls on the keyless entry keypad, press the middle of the controls to ensure a good activation. Programming your own personal entry code 1.
Page 90 Controls and features Anti-scan feature The keyless entry pad is disabled for 1 minute after 7 unsuccessful 7 8 9 0 attempts at entering a valid key code. The keypad will flash during this 1 minute mode. However, the 7/8 and 9/0 controls will still lock the vehicle.
Page 91 Controls and features Autolock The autolock feature will lock all of the vehicle doors when: • all doors are closed • ignition key is in the ON position • you shift into or through R (reverse) • the brake pedal is released The autolock feature repeats when: •...
Page 92 The SecuriLock passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Automatic arming...
Page 93 If a problem occurs, turn ignition OFF and restart the engine with all other objects on the key ring held away from the ignition key. Check to make sure the coded key is an approved Ford coded key.
Page 94 Controls and features If your keys are lost or stolen you will need to do the following: • Use your spare key to start the vehicle, or • Have your vehicle towed to a dealership or locksmith. The key codes will need to be erased from your vehicle and new key codes will need to be re-coded.
Page 95 Controls and features 1. Insert the first previously programmed coded key into the ignition and turn the ignition from 3 (OFF) to 4 (ON) (maintain ignition in 4 (ON) for at least one second). 2. Turn ignition to 3 (OFF) then 2 (LOCK) and remove the first coded key from the ignition.
Page 96: Seating And Safety Restraints
Seating and safety restraints FRONT SEATS Adjustable head restraints Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 97 Seating and safety restraints Adjusting the front manual seat Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to reduce the risk of injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Page 98 Seating and safety restraints Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Page 99 Seating and safety restraints Using the manual lumbar support (if equipped) Turn the lumbar support control toward the front of vehicle to move the lumbar support forward for more direct support. Turn the lumbar support control toward the rear of vehicle to move the lumbar support back for less direct support.
Page 100 Seating and safety restraints Folding down rear 60/40 seats 1. Raise the rear seat head restraint. 2. Flip the bottom of the head restraint up, toward the front seat. 3. While holding the head restraint in “flat” position, lower the head restraint to the seat back.
Page 101 Seating and safety restraints 5. Push the seatback toward the front seat and completely down until it locks into place. A carpeted panel will flip down from the back panel to complete the load floor. Returning the rear 60/40 seats to upright position 1.
Page 102 Seating and safety restraints SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. To reduce the risk of injury, make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving.
Page 103 Seating and safety restraints Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. Energy Management Feature • This vehicle has a safety belt system with an energy management feature at the front seating position to help further reduce the risk of injury in the event of a head-on collision.
Page 104 Seating and safety restraints 2. To unfasten, push the release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes described below: Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free...
Page 105 Seating and safety restraints How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Page 106 Seating and safety restraints After any vehicle collision, the front passenger outboard seat belt system must be checked by a qualified technician to verify that the “automatic locking retractor” feature for child seats is still functioning properly. In addition, all seat belts should be checked for proper function.
Page 107 Seating and safety restraints Lap belts Adjusting the lap belt The lap belt should fit snugly and as low as possible around the hips, not across the waist. • 2nd row center seating position The lap belt will adjust automatically. To fasten, grasp the tongue, and with a continuous motion, pull out enough webbing to buckle the tongue into the correct buckle.
Page 108 Seating and safety restraints Conditions of operation If... Then... The driver’s safety belt is not The safety belt warning light buckled before the ignition switch illuminates 1-2 minutes and the is turned to the ON position... warning chime sounds 4-8 seconds.
Page 109 Seating and safety restraints The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... Consider... “Crashes are rare 36 700 crashes occur every day. The more we events” drive, the more we are exposed to “rare” events, even for good drivers.
Page 110 Seating and safety restraints One time disable Any time the safety belt is buckled and then unbuckled during an ignition ON cycle, Belt Minder will be disabled for that ignition cycle only. Deactivating/activating the belt minder feature Read steps 1 - 9 thoroughly before proceeding with the deactivation/activation programming procedure.
Page 111 (if equipped), LATCH child seat tether anchors and lower anchors (if equipped), and attaching hardware, should be inspected after a collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced.
Page 112 This information will assist Ford in the servicing of your vehicle and may help Ford better understand real world collisions and further improve the safety of future vehicles.
Page 113 Do not attempt to service, repair, or modify the air bag supplemental restraint systems or its fuses. See your Ford or Lincoln Mercury dealer. Modifications to the front end of the vehicle, including frame, bumper, front end body structure and tow hooks may affect the performance of the air bag sensors increasing the risk of injury.
Page 114 Seating and safety restraints Additional equipment may affect the performance of the air bag sensors increasing the risk of injury. Please refer to the Body Builders Layout Book for instructions about the appropriate installation of additional equipment. Children and air bags For additional important safety information, read all information on safety restraints in this guide.
Page 115 Seating and safety restraints How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation.
Page 116 Seating and safety restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the...
Page 117 Seating and safety restraints If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Page 118 To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all applicable Federal motor vehicle safety standards. Belt-positioning booster seats raise the child and provide a shorter, firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child.
Page 119 Seating and safety restraints A belt-positioning booster seat should be used if the shoulder belt rests in front of the child’s face or neck, or if the lap belt does not fit snugly on both thighs, or if the thighs are too short to let the child sit all the way back on the seat cushion when the lower legs hang over the edge of the seat cushion.
Page 120 (passenger side front and outboard rear seating positions) (if equipped) section in this chapter. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
Page 121 Seating and safety restraints Installing child safety seats in combination lap and shoulder belt seating positions Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.
Page 122 Seating and safety restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until...
Page 123 Seating and safety restraints 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt.
Page 124 Seating and safety restraints 5. If you have not pulled out enough webbing to reach, allow the webbing to fully retract before attempting to pull it out again and repeat steps 2 through 4. 6. Pull the webbing through the child seat toward the buckle while pushing down with your knee on the child seat.
Page 125 Seating and safety restraints 1. Position the child safety seat on the rear seat cushion. 2. Route the child safety seat tether strap over the back of the seat. For vehicles with adjustable head restraints, route the tether strap under the head restraint and between the head restraint posts, otherwise route the tether strap over the top of the seatback.
Page 126 Seating and safety restraints 4. Slide open the tether anchor cover. 5. Clip the tether strap to the anchor and return the seat back to its locked position. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision.
Page 127 Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
Page 128 Starting 2. Make sure the headlamps and vehicle accessories are off. • Make sure the parking brake is set. • Make sure the gearshift is in P (Park). 3. Turn the key to 4 (ON) without turning the key to 5 (START). If there is difficulty in turning the key, firmly rotate the steering wheel left and right until the key turns...
Page 129 Starting Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. STARTING THE ENGINE NOTE: Whenever you start your vehicle, release the key as soon as the engine starts.
Page 130 Cold starting performance can also be improved with the use of an engine block heater. The engine block heater is available as a Ford option and can also be obtained from your Ford dealer. Consult the engine block heater section for proper use of the engine block heater.
Page 131 Starting Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes.
Page 132: Driving
Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Page 133 Driving ABS warning lamp warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the...
Page 134 Driving The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the BRAKE ignition is turned ON) until the parking brake is released. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission).
Page 135 Driving If the steering wanders or pulls, the condition could be caused by any of the following: • underinflated tire(s) on any wheel(s) • uneven vehicle loading • high crown in center of road • high crosswinds • wheels out of alignment •...
Page 136 Driving Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions.
Page 137 Driving Do not drive your vehicle until you verify that the brakelamps are working. If your vehicle gets stuck in mud or snow it may be rocked out by shifting between forward and reverse gears, stopping between shifts, in a steady pattern.
Page 138 Driving Understanding gearshift positions Hold the brake pedal down while you move the gearshift lever from P (Park) to another position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone. P (Park) To put your vehicle in gear, start the engine, depress the brake pedal, then move gearshift lever out of P (Park).
Page 139 Driving (Overdrive) can be deactivated by pressing the transmission control switch on the end of the gearshift ON/OFF lever. The transmission control indicator light (TCIL) will illuminate on the instrument cluster. Drive – Not shown on the display. Activate by pressing the transmission control switch on the end of the gearshift lever with the gearshift in (Overdrive) position.
Page 140 Driving 1 (First) Use 1 (First) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive). Selecting 1 (Low) at higher speeds causes the transmission to shift to a lower gear and will shift to 1 (First) after the vehicle decelerates to the proper vehicle speed.
Page 141 Driving Recommended shift speeds Upshift according to the following charts for best fuel economy: Upshifts when accelerating (recommended for best fuel economy) 22 km/h (14 mph) 40 km/h (25 mph) 55 km/h (34 mph) 70 km/h (44 mph) Upshifts when cruising (recommended for best fuel economy) 19 km/h (12 mph) 31 km/h (19 mph) 46 km/h (29 mph)
Page 142 Driving 2. Engage the parking brake. 3. Shift into 1 (First). 4. Turn the ignition to Off. Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully.
Page 143 4WD system indicator lights The 4WD system indicator lights illuminate only under the following conditions. If these lights illuminate when driving in 2WD, contact your Ford dealer as soon as possible. • 4WD HIGH–momentarily illuminates when the vehicle is started. Illuminates when 4H (4WD High) is engaged.
Page 144 Driving Shifting from 4X4 HIGH (4WD high) to 2WD (2WD high) Move the 4WD control to 2WD position at any forward speed. HIGH • You do not need to operate the vehicle in R (Reverse) to disengage the 4WD system. Shifting from 2WD (2WD high) to 4X4 LOW (4WD low) 1.
Page 145 Driving 4. Move the 4WD control to the 2WD position. HIGH 5. Wait for the 4WD low indicator light to turn off. Shifting between 4X4 HIGH (4WD high) and 4X4 LOW (4WD low) 1. Bring the vehicle to a stop. 2.
Page 146 Driving If your vehicle gets stuck If the vehicle is stuck it may be rocked out by shifting from forward and reverse gears, stopping between shifts, in a steady pattern. Press lightly on the accelerator in each gear. Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur.
Page 147 Driving Replace rear axle lubricant any time the axle has been submerged in water. The rear axle does not normally require a lubricant change for the life of the vehicle. Rear axle lubricant quantities are not to be checked or changed unless a leak is suspected or repair is required.
Page 148 Driving VEHICLE LOADING Before loading a vehicle, familiarize yourself with the following terms: • Base Curb Weight: Weight of the vehicle including any standard equipment, fluids, lubricants, etc. It does not include occupants or aftermarket equipment. • Payload: Combined maximum allowable weight of cargo, occupants and optional equipment.
Page 149 Driving Do not exceed the GVWR or the GAWR specified on the certification label. Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher limit than the originals do not increase the GVWR and GAWR limitations.
Page 150 Driving Calculating the load your vehicle can carry/tow 1. Use the appropriate maximum gross combined weight rating (GCWR) chart to find the maximum GCWR for your type engine and rear axle ratio. 2. Weigh your vehicle as you customarily operate the vehicle without cargo.
Page 151 Driving Follow these guidelines to ensure safe towing procedure: • Stay within your vehicle’s load limits. • Thoroughly prepare your vehicle for towing. Refer to Preparing to tow in this chapter. • Use extra caution when driving while trailer towing. Refer to Driving while you tow in this chapter.
Page 152 Driving 4x2 w/manual transmission GCWR (Gross Combined Weight Rating)/Trailer weights Trailer Weight Rear Maximum Maximum Range-kg Engine axle GCWR-kg frontal area of (lbs.) ratio (lbs.) trailer-m 0-Maximum 4.0L 3 175 0-1 243 4.64 (50) SOHC (7 000) (0-2 740) Notes: For high altitude operation, reduce GCW by 2% per 300 meters (1 000 ft) elevation.
Page 153 Driving 4x4 w/manual transmission GCWR (Gross Combined Weight Rating)/Trailer Weights Trailer Weight Maximum Rear Maximum Range frontal area of Engine axle GCWR - kg (0-Maximum) trailer - m ratio (lbs.) - kg (lbs.) 4.0L 3 175 0-1 143 4.64 (50) SOHC (7 000) (0-2 520)
Page 154 Never connect any trailer lighting to the vehicle’s taillamp circuits, because it may damage the electrical system resulting in fire. Contact your local Ford dealership for assistance in proper trailer tow wiring installation. Additional electrical equipment may be required.
Page 155 Driving Driving while you tow When towing a trailer: • Ensure that you turn off your speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer. •...
Page 156 Driving Launching or retrieving a boat When backing down a ramp during boat launching or retrieval: • do not allow the static water level to rise above the bottom edge of the rear bumper and • do not allow waves to break higher than 15 cm (6 inches) above the bottom edge of the rear bumper.
Page 157 Driving If a distance of 80 km (50 miles) or a speed of 56 km/h (35 mph) must be exceeded, you must disconnect the driveshaft. Ford recommends the driveshaft be removed/installed only by a qualified technician. See your local dealer for driveshaft removal/installation.
Page 158: Roadside Emergencies
Roadside emergencies Getting roadside assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week •...
Page 159 Roadside coverage beyond basic warranty In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer. Similarly in Canada, for uninterrupted Roadside Assistance coverage, you may purchase extended coverage prior to your Basic Warranty’s Roadside...
Page 160 Roadside emergencies The fuel pump shut-off switch is located in the passenger’s foot well, by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3.
Page 161 Roadside emergencies FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating.
Page 162 Roadside emergencies Passenger compartment fuse panel The fuse panel is located on the left-hand side of the instrument panel facing the driver’s side door. Pull the panel cover outward to access the fuses. To remove a fuse use the fuse puller tool provided on the fuse panel cover.
Page 163 Roadside emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Panel Location Rating Description Power Mirror Switch Aux. High Mount Stop Lamp 7.5A Left Stop/Turn Trailer Tow Connector Subwoofer — Not Used 15A (With Blower Motor Relay, Airbag Diagnostic rear blower) Monitor 7.5A (Without rear blower)
Page 164 Roadside emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Panel Location Rating Description 7.5A Generic Electronic Module (GEM), Radio, Moonroof Relay, Power Window Relay, Power Down Back Window Flasher (Hazard) Auxiliary Power Socket — Not Used 7.5A Starter Interrupt Relay, Anti-Theft 7.5A Generic Electronic Module (GEM), Instrument Cluster, Securi-Lock...
Page 165 Roadside emergencies Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Page 166 Roadside emergencies The high-current fuses are coded as follows. Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating 50A** Fuse Panel — Not Used 30A** Power Down Back Window — Not Used — Not Used 50A** ABS Pump Motor 30A** Powertrain Control —...
Page 167 Roadside emergencies Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating — Not Used — Not Used — Not Used — Not Used 10A* PCM Memory 15A* Horn 20A* Fuel Pump Motor 25A* Headlamps 10A* A/C Clutch Solenoid — Not Used 20A* Rear Power Point 30A*...
Page 168 Roadside emergencies Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating — Front Washer Pump Relay 20A* Windows/Roof — Not Used — Window Safety Relay — Starter Relay — Not Used — Fuel Pump Relay — Not Used — Not Used —...
Page 169 Roadside emergencies Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the following locations: Tool Location Spare tire Under the vehicle, just in front of the rear bumper Jack, Jack handle, jack handle In the passenger side rear cab extension, wheel lug nut wrench compartment behind the access...
Page 170 Roadside emergencies 2. Insert the jack handle into the opening just above the rear bumper. The handle will stop moving forward and resistance to turning will be felt when properly engaged. 3. Turn the handle counterclockwise until tire is lowered to the ground, and the cable is slack.
Page 171 Roadside emergencies Tire change procedure When one of the front wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the vehicle is in P (Park) (automatic transaxle) or R (Reverse) (manual transaxle).
Page 172 Roadside emergencies 4. Insert tapered end of the lug nut wrench to remove any wheel trim. 5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 6. Assemble the jack handle extension on the lug nut wrench by sliding the parts together.
Page 173 Roadside emergencies • Rear To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire.
Page 174 Roadside emergencies 11. Remove the jack and fully tighten the lug nuts in the order shown. 12. Stow the flat tire. Refer to Stowing the spare tire. 13. Stow the jack and lug nut wrench. Make sure the jack is fastened so it does not rattle when you drive.
Page 175 Roadside emergencies 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect any electrical surges. Turn all other accessories off. Connecting the jumper cables 1.
Page 176 Roadside emergencies 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system.
Page 177 Roadside emergencies • 4.0L SOHC V6 Engine 5. Ensure that the cables are clear of fan blades, belts, moving parts of both engines, or any fuel delivery system parts. Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed.
Page 178 Roadside emergencies • 4.0L SOHC V6 Engine 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery.
Page 179 Roadside emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Page 180 It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure.
Page 181 (all wheels on the ground) under the folling conditions: Ford Motor Company provides a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for...
Page 182: Maintenance And Care
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service.
Page 183 Maintenance and care Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the steering column on the instrument panel.
Page 184 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L SOHC V6 engine 1. Windshield washer fluid reservoir 2. Automatic transmission fluid dipstick (if equipped) 3. Engine oil filler cap 4. Engine oil dipstick 5. Brake fluid reservoir 6. Power distribution box 7.
Page 185 Maintenance and care ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan.
Page 186 Maintenance and care • If the oil level is below the ADD mark or MIN mark, add enough oil to raise the level within the ADD-FULL range or MIN-MAX range. • Oil levels above the letter F in FULL or the MAX mark may cause engine damage.
Page 187 Change your engine oil and filter according to the appropriate schedule listed in the scheduled maintenance guide. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced.
Page 188 MAX. Do not fill above this line. 4. Use only a DOT 3 brake fluid certified to meet Ford specification ESA-M6C25–A. Refer to Lubricant specifications in the Capacities and specifications chapter. Brake fluid is toxic. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes.
Page 189 If the fluid level drops, refill the fluid level to the step in the reservoir. Use only a DOT 3 brake fluid designed to meet Ford specification ESA-M6C25–A. Refer to Capacities and specifications. Brake fluid is toxic. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes.
Page 190 Only use a washer fluid that meets Ford specification . Refer to Lubricant specifications in the Capacities and specifications chapter. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive.
Page 191 Maintenance and care ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the mileage intervals listed in the scheduled maintenance guide. The coolant concentration should be maintained at 50/50 coolant and water, which equates to a freeze point of -36°...
Page 192 The cooling system in your vehicle is filled with either green-colored Motorcraft Premium Engine Coolant meeting Ford specification ESE-M97B44–A or yellow-colored Motorcraft Premium Gold Engine Coolant meeting Ford Specification WSS-M97B51–A1. To determine your vehicle’s coolant type (color), check your coolant reservoir. • Add Motorcraft Premium Engine Coolant (green-colored), VC-4–A (U.S.) or CXC-10 (Canada) or Motorcraft Premium...
Page 193 • Do not mix with recycled coolant unless from a Ford-approved recycling process (see Use of Recycled Engine Coolant section). For vehicles with overflow coolant systems with a non-pressurized cap on the coolant recovery system, add coolant to the coolant recovery reservoir when the engine is cool.
Page 194 Operating an engine with a low level of coolant can result in engine overheating and possible engine damage. Recycled engine coolant Ford Motor Company recommends the use of a recycled engine coolant produced by Ford-approved processes in vehicles originally equipped with Motorcraft Premium Engine Coolant (green-colored). However, not all coolant recycling processes produce coolant that meets Ford specification ESE-M97B44–A.
Page 195 Maintenance and care Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in the Capacities and specifications chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this chapter. Severe climates If you drive in extremely cold climates (less than –36°...
Page 196 Maintenance and care CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the scheduled maintenance guide for the service interval schedules. If adding fluid is necessary, use only MERCON ATF. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C).
Page 197 Maintenance and care operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking. 1. Drive the vehicle 30 km (20 miles) or until it reaches normal operating temperature.
Page 198 Maintenance and care The transmission fluid should be in this range if at ambient temperature (10°C-35°C [50°F-95°F]). High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage.
Page 199 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter.
Page 200 Maintenance and care BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the scheduled maintenance guide for the service interval schedules.
Page 201 Maintenance and care When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.
Page 202 Maintenance and care • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. RECYCLE WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective.
Page 203 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear...
Page 204 Maintenance and care The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 205 Maintenance and care Tire rotation Because your vehicle’s tires perform different jobs, they often wear differently. To make sure your tires wear evenly and last longer, rotate them as indicated in the scheduled maintenance guide. If you notice that the tires wear unevenly, have them checked. The following procedure applies to vehicles equipped with single rear wheels.
Page 206 Maintenance and care • Five tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label.
Page 207 The tires on your vehicle have all-weather treads to provide traction in rain and snow. However, in some climates, using snow tires or traction devices may be necessary. Ford offers tire cables as a Ford approved accessory and recommends use of these or SAE class “S”. See your dealer or qualified service technician for more information on tire cables for your vehicle.
Page 208 Maintenance and care • Do not exceed 48 km/h (30 mph) with tire cables or chains on your vehicle. Consult your dealer for information on other Ford approved methods of traction control. WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank.
Page 209 Maintenance and care Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automotive fuels can be harmful or fatal if swallowed. Fuels such as gasoline and ethanol are highly toxic and if swallowed can cause death or permanent injury.
Page 210 Maintenance and care Pure ethanol is the alcohol which is the intoxicating agent in liquor, beer and wine. It is distilled from the fermentation of plants such as field corn and sugar cane. When ethanol is used in the making of motor fuels, a small amount of a bad tasting chemical is added to discourage beverage use.
Page 211 Maintenance and care Use the following guidelines to avoid static build-up when filling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including the cargo area).
Page 212 Maintenance and care FFV engine (if equipped) Your vehicle is designed to use Fuel Ethanol(E85), “Regular” unleaded gasoline or any percentage of the two fuels combined. U.S. government regulations require fuel ethanol dispensing pumps to have a small, square, orange and black label with the common abbreviation E85 or the appropriate percentage for that region.
Page 213 “Ethanol Fuel Compatible” dispensing station equipment. These standards and guidelines can be obtained from Ford Motor Company. Fuel stations may apply to be certified as meeting these standards. However, not all stations meet these standards at this time. To ensure proper operation of your FFV on fuel ethanol, refuel at certified stations.
Page 214 The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
Page 215 Maintenance and care Fuel Filter For fuel filter replacement, see your dealer or a qualified service technician. Refer to the scheduled maintenance guide for the appropriate intervals for changing the fuel filter. Replace the fuel filter with an authorized Motorcraft part. The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft fuel filter is not used.
Page 216 Maintenance and care • Allow no more than 2 automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump and have the vehicle facing the same direction each time you fill up.
Page 217 Maintenance and care Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy. • Idling for long periods of time (greater than one minute) may waste fuel.
Page 218 Maintenance and care • Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy. • Using fuel blended with alcohol may lower fuel economy. • Fuel economy may decrease with lower temperatures during the first 12–16 km (8–10 miles) of driving.
Page 219 If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.
Page 220 Maintenance and care Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostics system. If your “Check Engine/Service Engine Soon” light is on, refer to the description in the Warning lights and chimes section of the Instrumentation chapter.
Page 221 Maintenance and care Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position, then lift hood and lift the plastic headlamp cover. 2. At the back of the headlamp, pry up and remove the two retainer pins to release the headlamp assembly from the vehicle and pull headlamp forward.
Page 222 Maintenance and care 1. With the flat side of the new bulb’s plastic base facing upward, insert the glass end of the bulb into the lamp assembly. Turn the bulb left or right to align the grooves in the plastic base with the tabs in the lamp assembly.
Page 223 Maintenance and care Replacing tail lamp/turn/backup lamp bulbs The tail lamp/turn/backup lamp bulbs are located in the same portion of the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb: 1. Lower the tailgate to expose the lamp assembly.
Page 224 Maintenance and care To remove the brakelamp assembly: 1. Remove the two screws and lamp assembly from vehicle. 2. Remove the bulb socket from lamp assembly by rotating it 45 degrees. 3. Carefully pull bulb straight out of socket and push in the new bulb. To install the brakelamp assembly: 1.
Page 225 Maintenance and care Function Number of bulbs Trade number Headlamps 9007 Park/turn/side marker 3157 AK (amber) lamps Rear stop/tail /turn lamps 3157K Backup lamp 3156K Hi-mount brake lamp Fog lamp 9145 Rear license plate lamps Overhead map lamp PC579 (XU5A-13466-AA) Map lamps 168 (T10) Dome lamp...
Page 226 Maintenance and care Vertical aim adjustment 1. Park the vehicle on a level surface approximately 7.6 meters (25 feet) from a vertical wall or screen directly in front of it. This procedure should be done in a dark enviroment to effectively see the headlamp beam pattern.
Page 227 AND IS NON-ADJUSTABLE. 7. Close the hood and turn off the lamps. CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance chapter for a list of Ford-approved cleaners, polishes and waxes. Washing your vehicle Wash your vehicle regularly with cold or lukewarm water.
Page 228 Ultra Touch Prep and Finishing Kit (F7AZ-19K507–BA), Lacquer Touch-up Paint (ALBZ-19500–XXXXA), or Exterior Acrylic Spray Lacquer (ALAZ-19500–XXXXA) from the Ford Car Care Chemicals line. Please note that the part numbers (shown as XXXX above) will vary with your vehicle’s specific coloring. Observe the application instructions on the products.
Page 229 Maintenance and care Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. The high pressure fluid could penetrate the sealed parts and cause damage.
Page 230 Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. If necessary, use a tar remover such as Ford Extra Strength Tar and Road Oil Remover (B7A-19520–AA). To avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners.
Page 231 For tougher soiling concerns, Ford recommends using the Deluxe Leather Care Kit F8AZ-19G253–AA, which is available from your Ford Dealer. This mild cleaner and special pad, cleans the leather and maintains its natural beauty. Follow the instructions on the cleaner label.
Page 232 Maintenance and care Inside windows Use Ultra-Clear Spray Glass Cleaner (E4AZ-19C507–AA) for the inside windows if they become fogged. Cleaning mirrors Do not clean your mirrors with a dry cloth or abrasive materials. Use a soft cloth and mild detergent and water. Be careful when removing ice from outside mirrors because you may damage the reflective surface.
Page 233: Capacities And Specifications
FL-820S PCV valve EV-243 Spark plugs* AGSF-22PP * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. REFILL CAPACITIES Fluid Ford Part Application Capacity Name Brake and High Fill to line on clutch fluid Performance reservoir...
Page 234 Capacities and specifications Fluid Ford Part Application Capacity Name Engine coolant Motorcraft 4.0L SOHC V6 13.2L (14.0 Premium Engine engine quarts) Coolant (green-colored) or Motorcraft Premium Gold Engine Coolant (yellow-colored) Front axle Motorcraft SAE 4x4 vehicles 1.7L (1.8 lubricant 80W-90...
Page 235 The axle lubricant should be changed any time the axle has been submerged in water. Add 118 ml (4 oz.) of Additive Friction Modifier C8AZ-19B546-A or equivalent meeting Ford specification EST-M2C118–A for complete refill of Traction-Lok axles. LUBRICANT SPECIFICATIONS...
Page 236 Capacities and specifications Ford Part Ford Part Ford Item Name or Number Specification equivalent Engine coolant Motorcraft VC-4–A (US) or ESE-M97B44-A Premium Engine CXC-10 Coolant (Canada) (green-colored) Motorcraft VC-7–A WSS-M97B51-A1 Premium Gold Engine Coolant (yellow-colored) Motorcraft SAE WSS-M2C153-G 5W-30 Super...
Page 237 MERCON and MERCON V. Refer to your scheduled maintenance guide to determine the correct service interval. Conventional rear axles are filled with Motorcraft SAE 80W-90 Premium Rear Axle Lubricant, part number XY-80W90-QL, Ford specification WSP-M2C197-A. Traction-Lok rear axles are filled with Motorcraft SAE 75W-140 High Performance Synthetic Rear Axle Lubricant, part number F1TZ-19780-B, Ford specification WSL-M2C192-A.
Page 238 Capacities and specifications ENGINE DATA Engine 4.0L SOHC V6 engine Cubic inches Required fuel 87 octane Firing order 1-4-2-5-3-6 Spark plug gap 1.3-1.4 mm (0.052-0.056 inch) Ignition system EDIS Compression ratio 9.7:1 VEHICLE DIMENSIONS Dimensions 4-Door mm (in.) (1) Overall length 5 230 (205.9) (2) Overall width 1 823 (71.8)
Page 239 Capacities and specifications...
Page 240 Capacities and specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the front door latch pillar on the driver’s side.
Page 241: Customer Assistance
United States and Canada, provided by a network of more than 5,000 participating Ford or Lincoln Mercury and Ford of Canada dealers. If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Please contact your dealer for further information.
Page 242 Ford Customer Relationship Center. Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
Page 243 P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) In order to help you service your Ford or Lincoln Mercury vehicle, please have the following information available when contacting a Customer Relationship Center: • Your telephone number (home and business).
Page 244 Customer assistance The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this service without notice and without incurring obligations per applicable state law.
Page 245 • the name of the dealer(s) who sold or serviced the vehicle • a brief description of your unresolved concern • a brief summary of the action taken by the dealer(s) and Ford Motor Company • the names (if known) of all the people you contacted at the dealership(s) •...
Page 246 After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board’s decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law.
Page 247 UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Page 248 If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY...
Page 249 Customer assistance Vehicle Security Styled wheel protector locks Vehicle security systems Comfort and convenience Celluar phone holder Compass mirror Compass mirror with temperature display Engine block heaters Seatback organizer Tire step Travel equipment Cargo cage Daytime running lights Factory luggage rack (cross bars) Factory luggage rack adaptors (bike, ski, luggage) Fog lights Front tow hooks...
Page 250 Customer assistance Protection and appearance equipment Air bag anti-theft locks Automatic headlamp system Bed mats Berber floor mats Carpet floor mats Cleaners, waxes and polishes Door edge guards Front end covers (full and mini) Hood deflectors Locking gas cap Lubricants and oils Molded splash guards Molded vinyl floor mats Rear window deflectors...
Page 251 • Ford cannot assume responsibility for any adverse effects or damage that may result from the use of such equipment. ORDERING ADDITIONAL OWNER’S LITERATURE...
Page 252 Customer assistance California Civil Code Section 1793.22(b) presumes that the manufacturer has had a reasonable number of attempts to conform the vehicle to its applicable express warranties if, within the first 18 months of ownership of a new vehicle or the first 29 000 km (18 000 miles), whichever occurs first: 1.
Page 253: Reporting Safety Defects
However, NHTSA cannot become involved in individual problems between you, your dealer or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (202–366–0123 in the Washington D.C.
Page 254: Index
Index acid, treating emergencies ..200 charging system Air bag supplemental restraint warning light ......11 system ........112 jumping a disabled battery ..174 and child safety seats ....114 maintenance-free ....200 description ......112 replacement, specifications ...233 disposal ........117 servicing ........200 driver air bag ......115 voltage gauge ......16 indicator light ....10, 117 Belt minder .......108...
Page 255 ....235, 238 Cruise control (see Speed Emergencies, roadside control) ........56 jump-starting ......174 Customer Assistance ....158 Emission control system ..218 Ford accessories for your Engine ........238 vehicle ........249 check engine/service engine Ford Extended Service soon light ........8 Plan ..........241 cleaning ........229 Getting assistance outside the coolant ........191...
Page 256 Index lubrication filling your vehicle specifications ....235, 238 with fuel ....208, 214–215 refill capacities ......233 filter, specifications ..215, 233 service points ......184 fuel pump shut-off switch ..159 starting after a collision ..159 gauge .........17 improving fuel economy ..215 Engine block heater ....130 octane rating ....211, 238 Engine oil ........185 quality ........212...
Page 257 Index driving with a heavy load ..148 storage ........168 location ........148 Jump-starting your vehicle ..174 Hazard flashers ......159 Keyless entry system ....88 Head restraints .....96, 99 autolock ........91 keypad ........88 Headlamps ........18 locking and unlocking doors ..90 aiming ......225–226 programming entry code ..89 bulb specifications ....224 daytime running lights .....18 Keys ........92–94...
Page 258 Index high beam .........11 overdrive off ......12 safety belt .........10 Panic alarm feature, remote speed control ......60 entry system ........86 turn signal indicator ....11 Parking brake ......133 Load limits .........148 Parts (see Motorcraft parts) ..233 GAWR ........148 Power distribution box (see GVWR ........148 Fuses) ........165 trailer towing ......148...
Page 259 Index for adults ......103–105 Tires ......168, 203–204 for children .....117–118 changing ......168, 171 lap belt ........107 checking the pressure ....204 warning light and replacing ........206 chime ....10, 13, 107–108 rotating ........205 snow tires and chains ....207 Safety seats for children ..119 tire grades .......204 Seat belts (see Safety treadwear ........203...
Page 260 Index power down back window ..24 Windshield washer fluid and Warning chimes ......13 wipers Warning lights (see Lights) ..8 checking and adding fluid ..190 checking and cleaning ....202 Washer fluid ......190 operation ........61 Water, Driving through .....150 replacing wiper blades ...202 Windows Wrecker towing ......180 power .........68...
Page 264: Filling Station Information
Use either green-colored Motorcraft Premium Engine Coolant or yellow-colored Motorcraft Premium Gold Engine Coolant. DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter. Ensure the correct automatic transmission fluid is used. Transmission fluid requirements are indicated on the dipstick or on the dipstick handle.

Ford 2001 Explorer SportTrac User Manual

Quick Links

Related Manuals for Ford 2001 Explorer SportTrac

Summary of Contents for Ford 2001 Explorer SportTrac

Table of Contents