Ford 2001 Explorer Owner's Manual

page of 257

/ 257
Contents
Table of Contents
Bookmarks

Table of Contents

Quick Links

Before driving

Introduction

Instrumentation

Controls And Features

Seating And Safety Restraints

Starting and driving

Starting

Driving

Roadside Emergencies

Servicing

Maintenance And Care

Capacities And Specifications

Customer Assistance

Reporting Safety Defects

Index

photocopying, recording or by any information storage and retrieval system or translation

in whole or part is not permitted without written authorization from Ford Motor Company.

Ford may change the contents without notice and without incurring obligation.

Contents

120

125

151

174

224

232

244

245

Table of Contents

Summary of Contents for Ford 2001 Explorer

Page 1 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Ford may change the contents without notice and without incurring obligation.
Page 2: Introduction
Introduction The following warning may be required by California law: CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Page 3 INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation.
Page 4 SPECIAL NOTICES Using your vehicle with a snowplow Do not use this vehicle for snowplowing. Using your vehicle as an ambulance Do not use this vehicle as an ambulance. Your vehicle is not equipped with the Ford Ambulance Preparation Package.
Page 5 Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate than other types of vehicles. Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or an accident.
Page 6 Introduction These are some of the symbols you may see on your vehicle. Safety Alert Fasten Safety Belt Air Bag-Side Child Seat Installation Warning Brake System Brake Fluid - Non-Petroleum Based Master Lighting Switch Fog Lamps-Front Fuel Pump Reset Windshield Defrost/Demist Power Windows Front/Rear...
Page 7 Child Safety Door Lock/Unlock Panic Alarm Engine Coolant Do Not Open When Hot Avoid Smoking, Flames, or Sparks Explosive Gas Power Steering Fluid Emission System Passenger Compartment Air Filter Check fuel cap Vehicle Symbol Glossary Interior Luggage Compartment Release Symbol Engine Oil Engine Coolant Temperature...
Page 8: Instrumentation
Instrumentation Instrument panel dimmer control (pg. 21) Windshield wiper/washer control Headlamp control (pg. 20) Tilt steering wheel lever* (pg. 62) Parking brake release (pg. 126) * if equipped Instrument cluster (pg. 10) (pg. 62) Driver air bag Turn signal control (pg.
Page 9 Instrumentation Audio system (pg. 28) Rear window/washer 4wd control* control (pg. 136) (pg. 27) Rear window defroster control (pg. 26) Foglamp control* (pg. 20) Climate controls (pg. 22)
Page 10 Instrumentation WARNING LIGHTS AND CHIMES CHECK GAGE CHECK ENGINE CHECK FUEL Check engine Your vehicle is equipped with a computer that monitors the engine’s emission control system. This system is commonly known as the On Board Diagnostics System (OBD II). This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards.
Page 11 3. The fuel cap may not have been properly installed and securely tightened. These temporary malfunctions can be corrected by filling the fuel tank with high quality fuel of the recommended octane and/or properly installing and securely tightening the gas cap. After three driving cycles without these or any other temporary malfunctions present, the Check Engine light should turn off.
Page 12 Instrumentation Air bag readiness Momentarily illuminates when the ignition is turned ON. If the light fails to illuminate, continues to flash or remains on, have the system serviced immediately. Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts.
Page 13 Instrumentation Turn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the indicators stay on continuously or flash faster, check for a burned-out turn signal bulb. Refer to Bulbs in the Maintenance and care chapter. High beams Illuminates when the high beam headlamps are turned on.
Page 14 Instrumentation Four wheel drive low (if equipped) Momentarily illuminates after the engine is STARTED. Illuminates when four-wheel drive low is engaged. If the light continues to flash have the system serviced. Four wheel drive high (if equipped) Momentarily illuminates after the vehicle has been STARTED.
Page 15 Instrumentation Speed control This light comes on when either the SPEED SET/ACCEL or RESUME controls CONT are pressed. It turns off when the speed control OFF control is pressed, the brake or clutch (if equipped) is applied or the ignition is turned to the OFF position.
Page 16 Instrumentation GAUGES CHECK GAGE CHECK ENGINE CHECK FUEL Speedometer Indicates the current vehicle speed. DOOR AJAR RPMx1000 R N D 2 1 BRAKE km/h THEFT km/h SPEED CONT HIGH...
Page 17 Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool.
Page 18 Instrumentation Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. Battery voltage gauge This shows the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range (as indicated by arrows), have the...
Page 19 Instrumentation Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion. The ignition should be in the OFF position while the vehicle is being refueled.
Page 20: Controls And Features
Controls and features HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. Foglamp control (if equipped) The foglamps can be turned on when the headlamp control is in either of the following positions: Parking lamps...
Page 21 High beams Push forward to activate. Pull toward you to deactivate. Flash to pass Pull toward you to activate and release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. Rotate up to brighten.
Page 22 Controls and features CLIMATE CONTROL SYSTEM Manual heating and air conditioning system (if equipped) Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle.
Page 23 Controls and features A/C-Uses outside air to cool the vehicle. It is quieter than MAX A/C but not as economical. Airflow will be from the instrument panel registers. (Panel)-Distributes outside air through the instrument panel registers. However, the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode.
Page 24 Controls and features To reduce humidity buildup inside the vehicle in cold weather conditions, don’t drive with the climate control system in the OFF or MAX A/C position. To reduce humidity buildup inside the vehicle in warm weather conditions, don’t drive with the climate control system in the OFF position.
Page 25 To aid in side defogging/demisting in cold weather. 1. Select 2. Set the temperature control to full heat 3. Set the fan speed to HI 4. Direct the outer panel vents towards to side windows To increase airflow to the outer panel vents, close the central panel vents.
Page 26 Controls and features Select for air to flow through these vents: Select for air to flow through these vents: REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog.
Page 27 Controls and features The defroster turns off automatically after 10 minutes or when the ignition is turned to the OFF position. To manually turn off the defroster before 10 minutes have passed, push the control again. REAR WINDOW WIPER AND WASHER For rear wiper operation, rotate the R.WIPE rear window wiper and washer...
Page 28 Controls and features USING YOUR AUDIO SYSTEM Premium AM/FM Stereo/Cassette/Single CD VOL PUSH ON SEEK TUNE SCAN Volume/power control Press the control to turn the audio system on or off. Audio power can also be turned on by pressing the AM/FM select control or the tape/CD select control.
Page 29 AM/FM select The AM/FM select control works in radio, tape and CD modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in tape mode Press this control to stop tape play and begin radio play.
Page 30 Controls and features Seek function in tape mode Press to listen to the previous selection on the tape. Press to listen to the next selection on the tape. Seek function for CD or CD changer (if equipped) Press to seek to the previous track of the current disc.
Page 31 Controls and features Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. SIDE 1-2 COMP SHUFFLE 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.
Page 32 Controls and features Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the BASS control then press: to decrease the bass output to increase the bass output. Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output.
Page 33 to shift sound to the left and to shift sound to the right. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the FADE control then press: to shift the sound to the front and to shift the sound to the rear.
Page 34 Controls and features Rewind The rewind control works in tape and CD modes. In tape mode, radio play will continue until rewind is stopped (with the TAPE control) or the beginning of the tape is reached. In CD mode, pressing the REW control rewinds the CD within the current track.
Page 35 Dolby noise reduction Dolby noise reduction operates in tape mode. Dolby noise reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) the Dolby noise reduction. Dolby noise reduction is manufactured under license from Dolby Laboratories Licensing Corporation.
Page 36 Controls and features to decrease hours and to increase hours. To set the minute, press and hold the CLK control and press TUNE: to decrease minutes and to increase minutes. If your vehicle has a separate clock, (other than the digital radio display), the CLK control will not function in the above manner.
Page 37 Mute mode Press the MUTE control to mute the playing media. Press the MUTE control again to return to the playing media. AM/FM Stereo In Dash Six CD Radio for Pioneer SHUF SCAN LOAD PUSH ON Volume/power control Press the control to turn the audio system on or off.
Page 38 Controls and features Turn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio and CD modes.
Page 39 Tune adjust for CD mode Press to select the previous disc. (Play will begin on the first track of the disc unless shuffle mode is engaged.) Refer to Shuffle feature for more information. Hold the control to continue reversing through the discs. Press to select the next disc.
Page 40 Controls and features Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode. Scan function in CD mode Press the SCAN control to hear a short sampling of all selections on the CD.
Page 41 Controls and features Starting autostore 1. Press and momentarily hold the AM/FM control. 2. AUTOSET will flash in the display as the frequency band is scrolled through. 3. When the six strongest stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available.
Page 42 Controls and features Display description Six circles are always lit in the digital display. These signify the six CD slots in the audio system. When a disc is loaded into a particular slot (1–6), the number inside that specific circle lights. If the circle is empty, there is no CD in that particular slot.
Page 43 Controls and features Eject Press the EJ control to stop and eject a CD. You can choose which CD will be ejected by pressing the EJ control and the desired preset number (1–6). For example, to eject CD 2, press the EJ control and then press the preset 2 control.
Page 44 Controls and features Fast forward The fast forward control works in CD modes. Press and hold the FF control until the desired selection is reached. If the end of the disc is reached, the CD will return to the first track on the first disc.
Page 45 Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the BASS control. Use the SEL control to increase or decrease the amount of bass. Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output.
Page 46 Controls and features Menu mode The MENU control allows you to access many different features within your audio system. There are three sets of menus available depending upon which mode or feature is activated. While in FM mode, two menus are available.
Page 47 Controls and features Traffic announcements This feature allows you to hear traffic announcements. When in this MENU mode, traffic announcements will interrupt radio and CD play. When in FM mode and RDS is activated, press the MENU until TRAFFIC OFF displays. Press the SEL control to engage the feature.
Page 48 Controls and features Radio data system (RDS) feature This feature allows your audio system to receive text information from RDS-equipped FM radio stations. To activate RDS: When in FM mode, press the MENU control until RDS OFF displays. Press the SEL control to engage this feature (RDS ON). RDS features: Once the RDS feature is on, press the MENU control to scroll through the following selections:...
Page 49 Press the MENU control until FIND program type is displayed. Use the SEL control to select the program type. With the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: Classic Country Info Jazz...
Page 50 Controls and features Press the DSP control to access the DSP menu. Press the SEL control to enter one of the following modes: DSP OFF SIGNAL MODE OCCUPANCY MODE Use the SEL control to select the desired signal mode (the selected mode will appear in the display).
Page 51 Use the SEL control to manually set the time. Press to increase hours/minutes. Press to decrease hours/minutes. Press the MENU control again to disengage the clock mode. Rear seat controls (if equipped) The rear seat controls allow the middle seat passengers to operate the radio, tape, CD or CD changer (if equipped).
Page 52 Controls and features Adjusting the volume Press the + control to increase volume. Press the - control to decrease volume. From the rear seat controls, volume control can be set no higher than the current radio setting unless the speakers are turned off. Refer to Turning speakers on and off.
Page 53 Mode select Push the MODE control to toggle between AM, FM1, FM2, tape, CD or CD changer (if equipped). Memory preset control Push the MEMORY control successively to allow rear seat passengers to scroll through the 6 memory presets in AM, FM1 or FM2.
Page 54 Controls and features Cleaning compact discs Inspect all discs for contamination before playing. If necessary, clean discs only with an approved CD cleaner and wipe from the center out to the edge. Do not use circular motion. CD and CD changer care Handle discs by their edges only.
Page 55 Radio frequency information The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission(CRTC) establish the frequencies AM and FM stations may use for their broadcasts. Allowable frequencies are: AM 530, 540–1600, 1610 kHz FM 87.7, 87.9–107.7, 107.9 MHz Not all frequencies are used in a given area.
Page 56 Controls and features TURN SIGNAL CONTROL Push down to activate the left turn signal. Push up to activate the right turn signal. POSITIONS OF THE IGNITION 1. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running.
Page 57 SPEED CONTROL (IF EQUIPPED) To turn speed control on Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not shift the gearshift lever into N (Neutral) with the speed control on.
Page 58 Controls and features To set a speed Press SET ACC. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed.
Page 59 To set a higher set speed Press and hold SET ACC. Release the control when the desired vehicle speed is reached or Press and release SET ACC to operate the Tap-Up function. Each press will increase the set speed by 1.6 km/h (1 mph) or Accelerate with your accelerator pedal.
Page 60 Controls and features To disengage speed control Depress the brake pedal or Depress the clutch pedal (if equipped). Disengaging the speed control will not erase the previously programmed set speed or engine RPM. Pressing OFF will erase the previously programmed set speed or engine RPM.
Page 61 To return to a previously set speed Press RSM. For RSM to operate, the vehicle speed must be faster than 48 km/h (30 mph). Indicator light This light comes on when either the SET ACCEL or RES controls are pressed. It turns off when the speed control OFF control is pressed, the brake is applied, the clutch pedal is applied (if equipped), or the ignition is turned to the OFF position.
Page 62 Controls and features TILT STEERING WHEEL (IF EQUIPPED) Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control to lock the steering wheel in position. Never adjust the steering wheel when the vehicle is moving.
Page 63 Push (tap) the end of the stalk briefly for a single swipe (no wash). Push and hold for three swipes with wash. Push and hold for a longer wash (up to ten seconds). Speed dependent wipers When the windshield wiper control is set on the intermittent settings, speed-sensitive front wipers automatically adjust as the vehicle’s speed changes.
Page 64 Controls and features OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package. Storage compartment (if equipped) Press the OPEN control to open the storage compartment. The door will open slightly and can be moved to full open.
Page 65 Place the provided height adaptors onto the back of the GARAGE control as needed. Press the GARAGE control to activate the transmitter. Moon roof (if equipped) You can move the glass panel of the moon roof back to open or tilt up to ventilate the vehicle.
Page 66 Controls and features Do not let children play with the moon roof. They may seriously hurt themselves. Electronic compass/temperature display (if equipped) Outside air temperature The outside temperature display is contained in the overhead console. The temperature display can be turned off and on by pressing the MODE control on the overhead console.
Page 67 Controls and features Compass zone adjustment 1. Determine which magnetic zone you are in by referring to the zone map. 2. Turn ignition to the ON position. 3. Press and hold the MODE control until VAR appears in the display, then release.
Page 68 Controls and features Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines: Press and hold the MODE control until CAL appears in the display (approximately eight seconds) and release. Drive the vehicle slowly (less than 5 km/h [3 mph]) in circles until CAL indicator turns off in about 2–3 complete circles.
Page 69 POWER WINDOWS Press and hold the rocker switches to open and close windows. Press the top portion of the rocker switch to close. Press the bottom portion of the rocker switch to open. One touch down Press AUTO completely down and release quickly.
Page 70 Controls and features POWER DOOR LOCKS Press control to unlock all doors. Press control to lock all doors. POWER SIDE VIEW MIRRORS To adjust your mirrors: 1. Select to adjust the left mirror or to adjust the right mirror. 2. Move the control in the direction you wish to tilt the mirror.
Page 71 Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash. CENTER CONSOLE Your vehicle may be equipped with a variety of console features. These include: Utility compartment with compact disc storage Auxiliary power point Cupholders Ashcup...
Page 72 Controls and features AUXILIARY POWER POINT The power point is an additional power source for electrical accessories. With full console. Without full console. Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty.
Page 73 POSITIVE RETENTION FLOOR MAT Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. To remove the floor mat, reverse the installation procedure.
Page 74 Controls and features CARGO COVER (IF EQUIPPED) Your vehicle may be equipped with a cargo area shade that covers the luggage compartment of your vehicle. To install the shade: 1. Fasten the cover into the mounting brackets (make sure the cover is right side up).
Page 75 2. Wrap the vinyl around the roller tube twice. Tuck the edges of the vinyl inside the end cap with each wrap. 3. Fold the edges of the vinyl towards the center, making sure that the edges clear the end cap slots.
Page 76 Controls and features The remote entry system allows you to lock or unlock all vehicle doors without a key. The remote entry features only operate with the ignition in the LOCK position. If there is any potential remote keyless entry problem with your vehicle, ensure ALL key fobs (remote entry transmitters) are brought to the dealership, to aid in troubleshooting.
Page 77 Sounding a panic alarm Press this control to activate the alarm. To deactivate the alarm, press the control again or turn the ignition to Panic alarm will only operate with the ignition in the OFF position. Replacing the battery The transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent.
Page 78 Controls and features Replacing lost transmitters If a remote transmitter has been lost and you would like to remove it from the vehicle’s memory, or you would like to purchase additional remote transmitters and have them programmed to your vehicle: Take all your vehicle’s transmitters to your dealer for programming, or...
Page 79 Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm. The system automatically turns off after 25 seconds or when the ignition is turned to the ON position. The dome lamp control (if equipped) must not be set to the OFF position for the illuminated entry system to operate.
Page 80 Controls and features The factory-set code is located: on the owner’s wallet card in the glove compartment marked on the computer module When pressing the controls on the keyless entry keypad, press the middle of the controls to ensure a good activation. Programming your own personal entry code 1.
Page 81 Anti-scan feature The keyless entry pad is disabled for 1 minute after 7 unsuccessful attempts at entering a valid key code. The keypad will flash during this 1 minute mode. However, the 7/8 and 9/0 controls will still lock the vehicle.
Page 82 Controls and features Autolock The autolock feature will lock all of the vehicle doors when: all doors are closed ignition key is in the ON position you shift into or through R (reverse) the brake pedal is released The autolock feature repeats when: any door is opened then closed while the engine is running and you put the vehicle in motion by releasing the brake pedal Deactivating autolock...
Page 83 The SecuriLock passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Automatic arming...
Page 84 If a problem occurs, turn ignition OFF and restart the engine with all other objects on the key ring held away from the ignition key. Check to make sure the coded key is an approved Ford coded key.
Page 85 If your keys are lost or stolen you will need to do the following: Use your spare key to start the vehicle, or Have your vehicle towed to a dealership or locksmith. The key codes will need to be erased from your vehicle and new key codes will need to be re-coded.
Page 86 Controls and features 1. Insert the first previously programmed coded key into the ignition and turn the ignition from 3 (OFF) to 4 (ON) (maintain ignition in 4 (ON) for at least one second). 2. Turn ignition to 3 (OFF) then 2 (LOCK) and remove the first coded key from the ignition.
Page 87: Seating And Safety Restraints
Seating and safety restraints FRONT SEATS Adjustable head restraints Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 88 Seating and safety restraints Adjusting the front manual seat Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to reduce the risk of injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Page 89 Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Page 90 Seating and safety restraints Using the manual lumbar support (if equipped) Turn the lumbar support control toward the front of vehicle to move the lumbar support forward for more direct support. Turn the lumbar support control toward the rear of vehicle to move the lumbar support back for less direct support.
Page 91 Seating and safety restraints Once the tip slide feature has been activated, the seat will not re-latch until the seatback is moved into the latched upright position by lifting the seatback control (1). This will engage the seat track locking levers. The tip slide feature can also be activated from the rear seat position.
Page 92 Seating and safety restraints Folding rear seats If the rear seat is equipped with adjustable head restraints, they should be placed in the full down position before folding the seat back down. 1. Pull the release control up to unlatch the seatback. 2.
Page 93 To return the seat to the upright position: Pull the release handle upward to unlatch the seat. Rotate the seatback upward until the seatback latches in the upright position. The seatback will click when it is locked into position. SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Page 94 Seating and safety restraints It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Page 95 BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the safety belt assembly “automatic locking retractor” feature or any other safety belt function is not operating properly when checked according to the procedures in Workshop Manual. Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions.
Page 96 Seating and safety restraints How to use the automatic locking mode Buckle the combination lap and shoulder belt. Grasp the shoulder portion and pull downward until the entire belt is extracted. Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Page 97 How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. After any vehicle collision, the front passenger outboard seat belt system must be checked by a qualified technician to verify that the “automatic locking retractor”...
Page 98 Seating and safety restraints Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button and slide the height adjuster down.
Page 99 Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON position...
Page 100 Seating and safety restraints The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... “Crashes are rare events” “I’m not going far” 3 of 4 fatal crashes occur within 25 miles of home. “Belts are uncomfortable”...
Page 101 One time disable Any time the safety belt is buckled and then unbuckled during an ignition ON cycle, Belt Minder will be disabled for that ignition cycle only. Deactivating/activating the belt minder feature Read steps 1 - 9 thoroughly before proceeding with the deactivation/activation programming procedure.
Page 102 (if equipped), LATCH child seat tether anchors and lower anchors (if equipped), and attaching hardware, should be inspected after a collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced.
Page 103 This information will assist Ford in the servicing of your vehicle and may help Ford better understand real world collisions and further improve the safety of future vehicles.
Page 104 Do not attempt to service, repair, or modify the air bag supplemental restraint systems or its fuses. See your Ford or Lincoln Mercury dealer.
Page 105 Modifications to the front end of the vehicle, including frame, bumper, front end body structure and tow hooks may affect the performance of the air bag sensors increasing the risk of injury. Do not modify the front end of the vehicle. Additional equipment may affect the performance of the air bag sensors increasing the risk of injury.
Page 106 Seating and safety restraints How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation.
Page 107 The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the air bag.
Page 108 Seating and safety restraints Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Page 109 Do not attempt to service, repair, or modify the air bag supplemental restraint system, its fuses or the seat cover on a seat containing an air bag. See your Ford or Lincoln Mercury dealer. All occupants of the vehicle including the driver should always wear their safety belts even when an air bag SRS is provided.
Page 110 Seating and safety restraints How does the side air bag system work? The side air bag system consists of the following: An inflatable nylon bag (air bag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks.
Page 111 Several air bag system components get hot after inflation. Do not touch them after inflation. If the side air bag has deployed, the air bag will not function again. The side air bag system (including the seat) must be inspected and serviced by a qualified technician in accordance with the vehicle service manual.
Page 112 Seating and safety restraints Disposal of air bags and air bag equipped vehicles (including pretensioners) For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel. SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children.
Page 113 To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all applicable Federal motor vehicle safety standards. Belt-positioning booster seats raise the child and provide a shorter, firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child.
Page 114 (passenger side front and outboard rear seating positions) (if equipped) section in this chapter. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
Page 115 Installing child safety seats in combination lap and shoulder belt seating positions Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.
Page 116 Seating and safety restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until...
Page 117 Seating and safety restraints 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt.
Page 118 Seating and safety restraints The tether strap anchors in your vehicle are in the following positions (shown from top view): Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor.
Page 119 4. Clip the tether strap to the anchor. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 5. Refer to the Installing child safety seats in combination lap and shoulder belt seating positions section of this chapter for further instructions to secure the child safety seat.
Page 120 Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
Page 121 2. Make sure the headlamps and vehicle accessories are off. Make sure the parking brake is set. Make sure the gearshift is in P (Park). 3. Turn the key to 4 (ON) without turning the key to 5 (START). If there is difficulty in turning the key, firmly rotate the steering wheel left and right until the key turns freely.
Page 122 Starting Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced. If the driver’s safety belt is fastened, the light may not illuminate. STARTING THE ENGINE NOTE: Whenever you start your vehicle, release the key as soon as the engine starts.
Page 123 Cold starting performance can also be improved with the use of an engine block heater. The engine block heater is available as a Ford option and can also be obtained from your Ford dealer. Consult the engine block heater section for proper use of the engine block heater.
Page 124 Starting To prevent electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters. Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately.
Page 125: Driving
Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Page 126 Driving ABS warning lamp warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the...
Page 127 The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission).
Page 128 Driving If the steering wanders or pulls, the condition could be caused by any of the following: underinflated tire(s) on any wheel(s) uneven vehicle loading high crown in center of road high crosswinds wheels out of alignment loose or worn suspension components TRACTION-LOK AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface.
Page 129 Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions.
Page 130 Driving Do not drive your vehicle until you verify that the brakelamps are working. If your vehicle gets stuck in mud or snow it may be rocked out by shifting between forward and reverse gears, stopping between shifts, in a steady pattern.
Page 131 Understanding gearshift positions Hold the brake pedal down while you move the gearshift lever from P (Park) to another position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone. P (Park) To put your vehicle in gear, start the engine, depress the brake pedal, then move gearshift lever out of P (Park).
Page 132 Driving (Overdrive) can be deactivated by pressing the transmission control switch on the end of the gearshift lever. The transmission control indicator light (TCIL) will illuminate on the instrument cluster. Drive – Not shown on the display. Activate by pressing the transmission control switch on the end of the gearshift lever with the gearshift in (Overdrive) position.
Page 133 1 (First) Use 1 (First) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive). Selecting 1 (Low) at higher speeds causes the transmission to shift to a lower gear and will shift to 1 (First) after the vehicle decelerates to the proper vehicle speed.
Page 134 Driving Recommended shift speeds Upshift according to the following charts for best fuel economy: Upshifts when accelerating (recommended for best fuel economy) Upshifts when cruising (recommended for best fuel economy) Reverse Ensure that the vehicle is at a complete stop before shifting into R (Reverse).
Page 135 2. Engage the parking brake. 3. Shift into 1 (First). 4. Turn the ignition to Off. Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully. FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this chapter.
Page 136 4WD system indicator lights The 4WD system indicator lights illuminate only under the following conditions. If these lights illuminate when driving in 2WD, contact your Ford dealer as soon as possible. 4WD HIGH-momentarily illuminates when the vehicle is started. Illuminates when 4H (4WD High) is engaged.
Page 137 Shifting from 4X4 HIGH (4WD high) to 2WD (2WD high) Move the 4WD control to 2WD position at any forward speed. You do not need to operate the vehicle in R (Reverse) to disengage the 4WD system. Shifting from 2WD (2WD high) to 4X4 LOW (4WD low) 1.
Page 138 Driving 4. Move the 4WD control to the 2WD position. 5. Wait for the 4WD low indicator light to turn off. Shifting between 4X4 HIGH (4WD high) and 4X4 LOW (4WD low) 1. Bring the vehicle to a stop. 2. Depress the brake. 3.
Page 139 You should either know the terrain or examine maps of the area before driving. Map out your route before driving in the area. For more information on driving off-road, read the “Four Wheeling” supplement in your owner’s portfolio. If your vehicle gets stuck If the vehicle is stuck it may be rocked out by shifting from forward and reverse gears, stopping between shifts, in a steady pattern.
Page 140 Driving Water intrusion into the transmission may damage the transmission. Replace rear axle lubricant any time the axle has been submerged in water. The rear axle does not normally require a lubricant change for the life of the vehicle. Rear axle lubricant quantities are not to be checked or changed unless a leak is suspected or repair is required.
Page 141 VEHICLE LOADING Before loading a vehicle, familiarize yourself with the following terms: Base Curb Weight: Weight of the vehicle including any standard equipment, fluids, lubricants, etc. It does not include occupants or aftermarket equipment. Payload: Combined maximum allowable weight of cargo, occupants and optional equipment.
Page 142 Driving Do not exceed the GVWR or the GAWR specified on the certification label. Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher limit than the originals do not increase the GVWR and GAWR limitations.
Page 143 Driving Calculating the load your vehicle can carry/tow 1. Use the appropriate maximum gross combined weight rating (GCWR) chart to find the maximum GCWR for your type engine and rear axle ratio. 2. Weigh your vehicle as you customarily operate the vehicle without cargo.
Page 144 Driving Thoroughly prepare your vehicle for towing. Refer to Preparing to tow in this chapter. Use extra caution when driving while trailer towing. Refer to Driving while you tow in this chapter. Service your vehicle more frequently if you tow a trailer. Refer to the severe duty schedule in the scheduled maintenance guide.
Page 145 GCWR (Gross Combined Weight Rating)/Trailer weights Rear Engine axle ratio 4.0L SOHC Notes: For high altitude operation, reduce GCW by 2% per 300 meters (1 000 ft) elevation. For definition of terms and instructions on calculating your vehicle’s load, refer to Vehicle loading in this chapter. Maximum trailer weights shown.
Page 146 Driving GCWR (Gross Combined Weight Rating)/Trailer Weights Rear Engine axle ratio 4.0L SOHC Notes: For high altitude operation, reduce GCW by 2% per 300 meters (1 000 ft) elevation. For definition of terms and instructions on calculating your vehicle’s load, refer to Vehicle loading in this chapter. Maximum trailer weights shown.
Page 147 Never connect any trailer lighting to the vehicle’s taillamp circuits, because it may damage the electrical system resulting in fire. Contact your local Ford dealership for assistance in proper trailer tow wiring installation. Additional electrical equipment may be required.
Page 148 Driving Driving while you tow When towing a trailer: Ensure that you turn off your speed control. The speed control may shut off automatically when you are towing on long, steep grades. Consult your local motor vehicle speed regulations for towing a trailer. Use a lower gear when towing up or down steep hills.
Page 149 Maximum distance is 80 km (50 miles). If a distance of 80 km (50 miles) or a speed of 56 km/h (35 mph) must be exceeded, you must disconnect the driveshaft. Ford recommends the driveshaft be removed/installed only by a qualified technician.
Page 150 Driving Place the transmission in N (Neutral). Do not exceed a distance of 80 km (50 miles). Do not exceed 56 km/h (35 mph) vehicle speed. RWD vehicles with 4x4 electronic shift transfer case and automatic transmission Regarding recreational towing or having your vehicle towed, 4x4 vehicles with electronic shift on the fly cannot be towed with any wheels on the ground (with the exception of moving it as a disabled vehicle off the road out of traffic).
Page 151: Roadside Emergencies
Getting roadside assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: 24–hours, seven days a week for the Basic warranty period (Canada) or New Vehicle Limited Warranty period (U.S.) of three years or 60 000 km (36 000 miles),...
Page 152 Roadside coverage beyond basic warranty In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer. Similarly in Canada, for uninterrupted Roadside Assistance coverage, you may purchase extended coverage prior to your Basic Warranty’s Roadside...
Page 153 Roadside emergencies The fuel pump shut-off switch is located in the passenger’s foot well, by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3.
Page 154 Roadside emergencies FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. NOTE: Always replace a fuse with one that has the specified amperage rating.
Page 155 Passenger compartment fuse panel The fuse panel is located on the left-hand side of the instrument panel facing the driver’s side door. Pull the panel cover outward to access the fuses. To remove a fuse use the fuse puller tool provided on the fuse panel cover.
Page 156 Roadside emergencies The fuses are coded as follows: Fuse/Relay Location Fuse Amp Passenger Compartment Fuse Rating Power Mirror Switch — Not Used 7.5A Left Stop/Turn Trailer Tow Connector Subwoofer Park Lamps 15A (With rear Blower Motor Relay, Airbag blower) Diagnostic Monitor 7.5A (Without rear blower) 7.5A...
Page 157 Fuse/Relay Fuse Amp Location Roadside emergencies Passenger Compartment Fuse Rating Cigar Lighter, Data Link Connector Power Door Locks PCM Power Diode 7.5A Generic Electronic Module (GEM), Radio, Moonroof Relay, Power Window Relay Flasher (Hazard) Auxiliary Power Socket — Not Used 7.5A Starter Interrupt Relay, Anti-Theft 7.5A...
Page 158 Roadside emergencies Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Page 159 The high-current fuses are coded as follows. Fuse/Relay Location Roadside emergencies Fuse Amp Power Distribution Box Rating 50A** Fuse Panel — Not Used — Not Used — Not Used — Not Used 50A** ABS Pump Motor 30A** Powertrain Control — Not Used —...
Page 160 Roadside emergencies Fuse/Relay Location Fuse Amp Power Distribution Box Rating 30A** Rear Defroster — Not Used — Not Used — Not Used 10A* PCM Memory 15A* Horn 20A* Fuel Pump Motor 25A* Headlamps 10A* A/C Clutch Solenoid — Not Used —...
Page 161 Fuse/Relay Location *Mini fuses **Cartridge fuses CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Spare tire information The spare tire can be used as a spare or a regular tire.
Page 162 Roadside emergencies Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the following locations: Tool Spare tire Jack, lug nut wrench Jack handle, jack handle extension Behind rear seat under carpet in Removing the spare tire 1.
Page 163 Stowing the spare tire 1. Lay the tire on the ground with the valve stem facing up. 2. Slide the wheel under the vehicle and install the retainer through the wheel center. 3. Turn the jack handle clockwise until the tire is raised to its original position underneath the vehicle.
Page 164 Roadside emergencies 3. Block the diagonally opposite wheel. 4. Insert tapered end of the lug nut wrench to remove any wheel trim. 5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 6.
Page 165 Roadside emergencies Front Rear...
Page 166 Roadside emergencies To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. Never use the differential as a jacking point.
Page 167 Roadside emergencies Do not attempt to push-start your vehicle. Automatic transmissions do not have push-start capability; also, the catalytic conveter may become damaged. Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its adaptive strategy. As a result of this, the transmission may shift firmly.
Page 168 Roadside emergencies 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system.
Page 169 Roadside emergencies 4.0L SOHC V6 Engine 5. Ensure that the cables are clear of fan blades, belts, moving parts of both engines, or any fuel delivery system parts. Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed.
Page 170 Roadside emergencies 4.0L SOHC V6 Engine 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery.
Page 171 Roadside emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Page 172 It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure.
Page 173 (all wheels on the ground) under the folling conditions: Ford Motor Company provides a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle.
Page 174: Maintenance And Care
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: We highlight do-it-yourself items in the engine compartment for easy location. We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service.
Page 175 Maintenance and care Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the steering column on the instrument panel.
Page 176 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L SOHC V6 engine 1. Windshield washer fluid reservoir 2. Automatic transmission fluid dipstick (if equipped) 3. Engine oil filler cap 4. Engine oil dipstick 5. Brake fluid reservoir 6. Power distribution box 7.
Page 177 ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan.
Page 178 Maintenance and care If the oil level is below the ADD mark or MIN mark, add enough oil to raise the level within the ADD-FULL range or MIN-MAX range. Oil levels above the letter F in FULL or the MAX mark may cause engine damage.
Page 179 Change your engine oil and filter according to the appropriate schedule listed in the scheduled maintenance guide. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced.
Page 180 MAX. Do not fill above this line. 4. Use only a DOT 3 brake fluid certified to meet Ford specification ESA-M6C25–A. Refer to Lubricant specifications in the Capacities and specifications chapter. Brake fluid is toxic. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes.
Page 181 If the fluid level drops, refill the fluid level to the step in the reservoir. Use only a DOT 3 brake fluid designed to meet Ford specification ESA-M6C25–A. Refer to Capacities and specifications. Brake fluid is toxic. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes.
Page 182 Only use a washer fluid that meets Ford specification . Refer to Lubricant specifications in the Capacities and specifications chapter. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive.
Page 183 ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the mileage intervals listed in the scheduled maintenance guide. The coolant concentration should be maintained at 50/50 coolant and water, which equates to a freeze point of -36° C (-34° F). Coolant concentration testing is possible with a hydrometer or antifreeze tester (such as the Rotunda Battery and Antifreeze Tester, 014–R1060).
Page 184 The cooling system in your vehicle is filled with either green-colored Motorcraft Premium Engine Coolant meeting Ford specification ESE-M97B44–A or yellow-colored Motorcraft Premium Gold Engine Coolant meeting Ford Specification WSS-M97B51–A1. To determine your vehicle’s coolant type (color), check your coolant reservoir. Add Motorcraft Premium Engine Coolant (green-colored), VC-4–A (U.S.) or CXC-10 (Canada) or Motorcraft Premium...
Page 185 Do not mix with recycled coolant unless from a Ford-approved recycling process (see Use of Recycled Engine Coolant section). For vehicles with overflow coolant systems with a non-pressurized cap on the coolant recovery system, add coolant to the coolant recovery reservoir when the engine is cool.
Page 186 Operating an engine with a low level of coolant can result in engine overheating and possible engine damage. Recycled engine coolant Ford Motor Company recommends the use of a recycled engine coolant produced by Ford-approved processes in vehicles originally equipped with Motorcraft Premium Engine Coolant (green-colored). However, not all coolant recycling processes produce coolant that meets Ford specification ESE-M97B44–A.
Page 187 Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in the Capacities and specifications chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this chapter. Severe climates If you drive in extremely cold climates (less than –36°...
Page 188 Maintenance and care CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the scheduled maintenance guide for the service interval schedules. If adding fluid is necessary, use only MERCON ATF. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C).
Page 189 Maintenance and care operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking. 1. Drive the vehicle 30 km (20 miles) or until it reaches normal operating temperature.
Page 190 Maintenance and care The transmission fluid should be in this range if at ambient temperature (10°C-35°C [50°F-95°F]). High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage.
Page 191 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter.
Page 192 Maintenance and care BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the scheduled maintenance guide for the service interval schedules.
Page 193 When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.
Page 194 Maintenance and care Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective.
Page 195 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear...
Page 196 Maintenance and care asphalt and concrete. A tire marked C may have poor traction performance. The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat...
Page 197 Maintenance and care Tire rotation Because your vehicle’s tires perform different jobs, they often wear differently. To make sure your tires wear evenly and last longer, rotate them as indicated in the scheduled maintenance guide. If you notice that the tires wear unevenly, have them checked. The following procedure applies to vehicles equipped with single rear wheels.
Page 198 Maintenance and care Five tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label.
Page 199 The tires on your vehicle have all-weather treads to provide traction in rain and snow. However, in some climates, using snow tires or traction devices may be necessary. Ford offers tire cables as a Ford approved accessory and recommends use of these or SAE class “S”. See your dealer or qualified service technician for more information on tire cables for your vehicle.
Page 200 Maintenance and care Do not exceed 48 km/h (30 mph) with tire cables or chains on your vehicle. Consult your dealer for information on other Ford approved methods of traction control. WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank.
Page 201 Extinguish all smoking materials and any open flames before fueling your vehicle. Always turn off the vehicle before fueling. Automotive fuels can be harmful or fatal if swallowed. Fuels such as gasoline and ethanol are highly toxic and if swallowed can cause death or permanent injury.
Page 202 Maintenance and care Pure ethanol is the alcohol which is the intoxicating agent in liquor, beer and wine. It is distilled from the fermentation of plants such as field corn and sugar cane. When ethanol is used in the making of motor fuels, a small amount of a bad tasting chemical is added to discourage beverage use.
Page 203 DO NOT fill a fuel container while it is in the vehicle (including the cargo area). Keep the fuel pump nozzle in contact with the fuel container while filling. DO NOT use a device that would hold the fuel pump handle in the fill position.
Page 204 Maintenance and care U.S. government regulations require fuel ethanol dispensing pumps to have a small, square, orange and black label with the common abbreviation E85 or the appropriate percentage for that region. Use of other fuels such as Fuel Methanol may cause powertrain damage, a loss of vehicle performance, and your warranty may be invalidated.
Page 205 “Ethanol Fuel Compatible” dispensing station equipment. These standards and guidelines can be obtained from Ford Motor Company. Fuel stations may apply to be certified as meeting these standards. However, not all stations meet these standards at this time. To ensure proper operation of your FFV on fuel ethanol, refuel at certified stations.
Page 206 The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
Page 207 Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal to the rated refill capacity of the fuel tank as listed in the Refill capacities section of the Capacities and specifications chapter. The advertised capacity is the amount of the indicated capacity and the empty reserve combined.
Page 208 Maintenance and care 5. Follow one of the simple calculations in order to determine fuel economy: Multiply liters used by 100, then divide by total kilometers traveled. Divide total miles traveled by total gallons used. Keep a record for at least one month and record the type of driving (city or highway).
Page 209 Resting your foot on the brake pedal while driving may reduce fuel economy. Combine errands and minimize stop-and-go driving. Maintenance Keep tires properly inflated and use only recommended size. Operating a vehicle with the wheels out of alignment will reduce fuel economy.
Page 210 If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.
Page 211 Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working.
Page 212 Maintenance and care Turn signals License plate lamp Tail lamps Back-up lamps Do not remove lamp bulbs unless they can be replaced immediately with new ones. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect lamp performance. Replacing headlamp bulbs To remove the headlamp bulb: 1.
Page 213 5. Without turning, remove the old bulb from the lamp assembly by gently pulling it straight back out of the lamp assembly. To install the new bulb: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass.
Page 214 Maintenance and care Replacing front parking lamp/turn signal bulbs 1. Remove screw from the lamp assembly. 2. Disengage lamp assembly. 3. Rotate bulb socket counterclockwise and remove from lamp assembly. 4. Carefully pull bulb straight out of socket and push in the new bulb. 5.
Page 215 Maintenance and care 5. Carefully pull the bulb straight out of the socket and push in the new bulb. 6. Install the bulb socket in lamp assembly by turning clockwise. 7. Install the lamp assembly and secure with two screws. Replacing foglamp bulbs 1.
Page 216 Maintenance and care USING THE RIGHT BULBS Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to assure lamp performance, light brightness and pattern and safe visibility.
Page 217 If your vehicle has been in an accident the alignment of your headlamps should be checked by a qualified service technician. Vertical aim adjustment 1. Park the vehicle on a level surface approximately 7.6 meters (25 feet) from a vertical wall or screen directly in front of it. This procedure should be done in a dark enviroment to effectively see the headlamp beam pattern.
Page 218 AND IS NON-ADJUSTABLE. 7. Close the hood and turn off the lamps. CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance chapter for a list of Ford-approved cleaners, polishes and waxes. Washing your vehicle Wash your vehicle regularly with cold or lukewarm water.
Page 219 Ultra Touch Prep and Finishing Kit (F7AZ-19K507–BA), Lacquer Touch-up Paint (ALBZ-19500–XXXXA), or Exterior Acrylic Spray Lacquer (ALAZ-19500–XXXXA) from the Ford Car Care Chemicals line. Please note that the part numbers (shown as XXXX above) will vary with your vehicle’s specific coloring. Observe the application instructions on...
Page 220 Maintenance and care Remove particles such as bird droppings, tree sap, insect remains, tar spots, road salt and industrial fallout immediately. Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: Take care when using a power washer to clean the engine.
Page 221 Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. If necessary, use a tar remover such as Ford Extra Strength Tar and Road Oil Remover (B7A-19520–AA). To avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners.
Page 222 For tougher soiling concerns, Ford recommends using the Deluxe Leather Care Kit F8AZ-19G253–AA, which is available from your Ford Dealer. This mild cleaner and special pad, cleans the leather and maintains its natural beauty. Follow the instructions on the cleaner label.
Page 223 Maintenance and care Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. Do not bleach or dye the belts, because these actions may weaken the belt webbing. Check the safety belt system periodically to make sure there are no nicks, tears or cuts.
Page 224: Capacities And Specifications
Fuel filter Battery Oil filter PCV valve Spark plugs* * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. REFILL CAPACITIES Fluid Ford Part Name Brake and High clutch fluid Performance DOT 3 Motor Vehicle Brake Fluid...
Page 225 Fluid Ford Part Name Engine coolant Motorcraft Premium Engine Coolant (green-colored) or Motorcraft Premium Gold Engine Coolant (yellow-colored) Front axle Motorcraft SAE lubricant 80W-90 Premium Rear Axle Lubricant Rear axle Motorcraft SAE lubricant 80W-90 Premium Rear Axle Lubricant Motorcraft SAE...
Page 226 The axle lubricant should be changed any time the axle has been submerged in water. Add 118 ml (4 oz.) of Additive Friction Modifier C8AZ-19B546-A or equivalent meeting Ford specification EST-M2C118–A for complete refill of Traction-Lok axles. LUBRICANT SPECIFICATIONS...
Page 227 Ford Part Item Name or equivalent Engine coolant Motorcraft Premium Engine Coolant (green-colored) Motorcraft Premium Gold Engine Coolant (yellow-colored) Motorcraft SAE 5W-30 Super Engine oil Premium Motor Automatic Motorcraft transmission MERCON V (5R55E) Motorcraft Power steering MERCON fluid Multi-Purpose Ford...
Page 228 MERCON and MERCON V. Refer to your scheduled maintenance guide to determine the correct service interval. Conventional rear axles are filled with Motorcraft SAE 80W-90 Premium Rear Axle Lubricant, part number XY-80W90-QL, Ford specification WSP-M2C197-A. Traction-Lok rear axles are filled with Motorcraft SAE 75W-140 High Performance Synthetic Rear Axle Lubricant, part number F1TZ-19780-B, Ford specification WSL-M2C192-A.
Page 229 VEHICLE DIMENSIONS Dimensions (1) Overall length (2) Overall width (3) Maximum height* (4) Wheelbase (5) Front track / rear * Height includes roof rack & P255 tire Capacities and specifications 2 Door 4x2 XL model mm (in.) 4 608 (181.4) 1 783 (70.2) 1 704 (67.1) 2 585 (101.8)
Page 230 Capacities and specifications...
Page 231 Capacities and specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the front door latch pillar on the driver’s side.
Page 232: Customer Assistance
5,000 participating Ford or Lincoln Mercury and Ford of Canada dealers. If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Please contact your dealer for further information. Since this information is subject to...
Page 233 Ford Customer Relationship Center. Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
Page 234 Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) In order to help you service your Ford or Lincoln Mercury vehicle, please have the following information available when contacting a Customer Relationship Center: Your telephone number (home and business).
Page 235 Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this service without notice and without incurring obligations per applicable state law.
Page 236 Ford Motor Company the names (if known) of all the people you contacted at the...
Page 237 After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board’s decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law.
Page 238 UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Page 239 If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY...
Page 240 Customer assistance Not all accessories are available for all models. Vehicle Security Styled wheel protector locks Vehicle security systems Comfort and convenience Cargo nets Cargo organizers Cargo shades Cargo trays Compass mirror Compass mirror with temperature display Engine block heaters Pet net Seatback organizer Tire step...
Page 241 Trailer hitch bars and balls Trailer hitch wiring adaptor Protection and appearance equipment Air bag anti-theft locks Cargo liners, interior (hard and soft) Carpet floor mats Cleaners, waxes and polishes Door edge guards Front end covers (full and mini) Front tow hooks Hood deflectors Locking gas cap Lubricants and oils...
Page 242 (Citizens band [CB] transceivers, garage door openers and other transmitters with outputs of five watts or less will not ordinarily affect your vehicle’s operation.) Ford cannot assume responsibility for any adverse effects or damage that may result from the use of such equipment. ORDERING ADDITIONAL OWNER’S LITERATURE...
Page 243 Customer assistance IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle’s applicable express warranty after a reasonable number of attempts, the manufacturer shall be required to either replace the vehicle with one substantially identical or repurchase the vehicle and reimburse the buyer in an amount equal to the actual price paid or payable by the consumer (less a reasonable allowance for consumer...
Page 244: Reporting Safety Defects
However, NHTSA cannot become involved in individual problems between you, your dealer or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (202–366–0123 in the Washington D.C.
Page 245: Index
Air bag supplemental restraint system ...103, 109 and child safety seats ...105 description ...103, 109 disposal ...112 driver air bag ...106, 110 indicator light ...12, 108, 111 operation ...106, 110 passenger air bag ...106, 110 side air bag ...109 Air cleaner filter ...182, 224 Air conditioning ...22 rear seat controls ...25 Ambulance packages ...4...
Page 246 ...183 refill capacities ...187, 224 specifications ...226, 228 Cruise control (see Speed control) ...57 Customer Assistance ...151 Ford accessories for your vehicle ...240 Ford Extended Service Plan ...232 Getting assistance outside the U.S. and Canada ...238 Getting roadside assistance ...151 Getting the service you need ...232...
Page 247 Engine ...228–229 check engine/service engine soon light ...10 cleaning ...220 coolant ...183 idle speed control ...192 lubrication specifications ...226, 228 refill capacities ...224 service points ...176 starting after a collision ...152 Engine block heater ...123 Engine oil ...177 checking and adding ...177 dipstick ...177 filter, specifications ...179, 224 recommendations ...179...
Page 248 Index GVWR (Gross Vehicle Weight Rating) ...141 calculating ...141, 143 definition ...141 driving with a heavy load ...141 location ...141 Hazard flashers ...152 Head restraints ...87, 91 Headlamps ...20 aiming ...216–217 bulb specifications ...216 daytime running lights ...20 flash to pass ...21 high beam ...13, 21 replacing bulbs ...212 turning on and off ...20...
Page 249 charging system ...13 check coolant ...13 check engine ...10 cruise indicator ...15 door ajar ...14 fuel cap light ...11 high beam ...13 overdrive off ...14 safety belt ...12 speed control ...61 turn signal indicator ...13 Load limits ...141 GAWR ...141 GVWR ...141 trailer towing ...141 Loading instructions ...142...
Page 250 Index Safety restraints ...93–98 belt minder ...99 cleaning the safety belts ...102, extension assembly ...98 for adults ...94–97 for children ...112 warning light and chime ...12, 15, Safety seats for children ...113 Seat belts (see Safety restraints) ...93 Seats child safety seats ...113 cleaning ...222 SecuriLock passive anti-theft system ...83–85...
Page 251 Warning chimes ...15 Warning lights (see Lights) ...10 Washer fluid ...182 Water, Driving through ...143 Windows power ...69 rear wiper/washer ...27 Windshield washer fluid and wipers ...27 checking and adding fluid ...182 checking and cleaning ...194–195 operation ...62 replacing wiper blades ...194 Wrecker towing ...172 Index...
Page 256: Filling Station Information
Use either green-colored Motorcraft Premium Engine Coolant or yellow-colored Motorcraft Premium Gold Engine Coolant. DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter. Ensure the correct automatic transmission fluid is used. Transmission fluid requirements are indicated on the dipstick or on the dipstick handle.

Ford 2001 Explorer Owner's Manual

Quick Links

Related Manuals for Ford 2001 Explorer

Summary of Contents for Ford 2001 Explorer

Table of Contents