Setting Up The Tool; Adjusting The Tool; Wall Set-Up; Tripod Set-Up - DeWalt DW077 User Manual

E N G L I S H
After the battery has cooled, the charger
automatically switches to the pack charging mode.
This feature ensures maximum battery life. The red
indicator (14) blinks long, then short while in the Hot
Pack Delay mode.
Battery type (fig. B3 & B4)
The tool is suitable for battery packs with different
voltages.
• To fit battery packs of 18 volt, rotate the adapter
plate (25) into position A.
• To fit battery packs of 9.6, 12 or 14.4 volt, rotate
the adapter plate (25) into position B.
Refer to the table in the back for a selection of
applicable battery packs.
Setting up the tool (fig. C1 - C5)
The tool facilitates various set-ups, making it useful
for several applications.
Floor set-up (fig. C1)
• Place the tool on a relatively smooth and level
surface.
• Adjust the tool for a level or plumb application.
Wall set-up (fig. C2 - C4)
The tool has been equipped with a wall mount (4) for
mounting to a wall track to aid in drop ceiling installation
and other specialty leveling projects (fig. C2).
• Fit the tool to the wall mount by inserting the
threaded pin (23) into one of the receptacles in
the tool and tightening the knob (8).
• Turn the tool on its side with the wall mount
clamp (6) in position for attachment to the wall
track (fig. C3).
• With the wall mount (4) facing the wall, turn the
wall mount clamping lock (7) in the clockwise
direction to open the clamp jaws.
• Place the clamp jaws around the wall track and
turn the wall mount clamping lock (7) in the anti-
clockwise direction to close the clamp jaws shut
on the track.
• Ensure that the wall mount clamping lock (7) is
securely locked.
Before attaching the tool to a wall track
ensure that the track is properly secured
to the wall.
38
• Alternatively, the tool can be hung on the wall
using the mounting holes (27) in the wall mount
(fig. C2).
- Hold the tool at the desired position against the
wall and mark the location of the two mounting
holes on the wall (fig. C4).
- Drill a hole at each of the marked locations
(required: ø 6 mm, approx. 35 mm deep).
- Insert a corresponding plug into each of the holes.
- Turn a screw into each of the plugs (required:
6 x 50 mm).
- Hang the tool on the screws.
• Adjust the leveling knob (3) to stabilise the tool
when necessary.
• Adjust the tool for a level application.
Tripod set-up (fig. C5)
The tool has been equipped with a tripod receptacle
for mounting to the DE0736 tripod (optional) or any
other tripod with the required ratings stated in the
technical data.
• Place the tripod (28) on a relatively smooth and
level surface.
• Mount the tool to the tripod by turning the
threaded pin (29) into the receptacle (30) in the
base.
• Adjust the tool for a level or plumb application.
Adjusting the tool (fig. A, D1 & D2)
The tool can be adjusted for both level (fig. D1) and
plumb (fig. D2) applications.
Self-leveling feature (fig. A)
• To initiate the leveling procedure, switch on the
tool. The leveling procedure is indicated by the
flashing of the leveling indicators (16 & 17) and
the laser beam. Once the tool has found its level
position the leveling indicators and the laser
beam will stop flashing and remain on.
• The leveling indicators and the laser beam
repeatedly flash three times rapidly to indicate
that the tool has been set up at a slope that is
beyond the self-leveling range of 5°. Switch the
tool off, re-adjust the tool set-up within the self-
leveling range and switch the tool on again.
Level adjustment (fig. D1)
• Place the tool into the required position as shown.
• Switch on the tool to initiate the leveling procedure.