Check, Change Or Delete A Programme; Making Timer Recordings On The Television; Linked Timer Recordings With External Equipment (Digital/Satellite Receiver)-Ext Link - Panasonic Diga DMR-ES10 Operating Instructions Manual

Check, change or delete a programme

RAM -R -RW(V) +R
Even when the unit is turned off, you can display the timer recording
list by pressing [PROG/CHECK].
Press [PROG/CHECK].
Icons
This programme is currently recording.
The times overlap those in another programme. Recording
W
of the programme with the later start time starts when the
earlier programme finishes recording.
The disc was full so the programme failed to record.
F
The material was copy-protected so it was not recorded.
The programme did not complete recording because the
X
disc is dirty or some other reason.
e.g.,
Continental Europe
TIMER
RECORDING
No. Name Date
01 ARD 15. 7. TUE
New Timer Programme
Message displayed in the "Disc space" line
OK: Displayed if the recording can fit in the remaining
space.
ENTER
RETURN
→ (Date):
For recordings made daily or weekly, the display
will show until when recordings can be made (up
to a maximum of one month from the present
time) based on the time remaining on the disc.
! : It may not be possible to record because:
•
the disc is write-protected
•
there is no more space left
•
the number of possible titles has reached its
maximum.
■ To change a programme
Press [e, r] to select the programme and press [ENTER].
(➔ page 20, Manually programming timer recordings, step 3)
■ To delete a programme
Press [e, r] to select the programme and press [
■ To exit the timer recording list
Press [PROG/CHECK].
■ To put the unit on timer recording standby
Press [z TIMER].
The unit turns off and "z" lights on the unit's display to indicate timer
recording standby has been activated.
•
Programmes that failed to record are deleted from the timer
recording list at 4 a.m. two days later.
Remain 1:58 SP
12:56:00 15. 7. TUE
VPS
Disc
Start Stop Mode
space
PDC
19:00 20:00 SP - - - OK
Cancel
CANCEL].
For Continental Europe
Making timer recordings on the
television
(e.g., of digital broadcasts)
RAM
-R -RW(V) +R
To make a timer recording with your television, connect to a
television with a Q Link function (➔ page 42) that you can use for
setting timer recordings using a fully wired 21-pin Scart cable
(➔ page 7).
1 Make timer programming on the TV.
2 Insert a disc.
3 Turn off the unit.
The start and end of recording is controlled by TV.
To stop recording
Press [g].
Note
•
When this unit is in timer recording standby or EXT LINK standby
("z" or "EXT Link" on the unit's display), recording from TV does
not start.
•
Programmes are recorded as one title on this unit when the end
time of the earlier timer recording and the start time of the later
timer recording are close to each other.
To divide the titles, go to "Divide Title" (➔ page 29).
RAM
For Continental Europe
Linked timer recordings with external
equipment (digital/satellite receiver)–
EXT LINK
RAM -R -RW(V) +R
To record programmes from a digital/satellite receiver using timer
programming
Preparation
•
Make sure you connect the AV2 input terminal of this unit to "VCR
Scart Terminal" of a digital/satellite receiver with a 21-pin scart
cable (➔ page 9).
•
Set the "AV2 Input" to match the connected equipment in the
SETUP menu (➔ page 36).
•
Set the "Ext Link" to match the connected equipment in the SETUP
menu (➔ page 36).
Ext Link 1: Start and stop timings of recording are controlled by
the control signal from a digital/satellite receiver.
Ext Link 2: When an external equipment with a timer function
turns on, recording starts.
When it turns off, recording stops.
1 Make timer programming on the external
equipment.
2 Insert a disc.
3 Press [EXT LINK].
The unit turns off and "EXT Link" lights on the unit's display to
indicate timer recording standby has been activated.
To cancel the external control
Press [EXT LINK] to stop recording or to cancel linked timer
recording standby.
•
In order to prevent accidental operation, press [EXT LINK] to
cancel the setting after recording is finished.
For your reference
•
This function does not work with some equipment. Refer to the
equipment's operating instructions.
•
The beginnings of recordings may not be recorded correctly in
some cases.
•
When "Ext Link" is set to "Ext Link 2", this function does not work if
the input signal is NTSC system.
•
When "AV2 Connection" is set to "Decoder", EXT LINK is not
available (➔ page 36).
•
Programmes are recorded as one title on this unit when the end
time of the earlier timer recording and the start time of the later
timer recording are close to each other.
To divide the titles, go to "Divide Title" (➔ page 29).
RAM
•
While the unit is in EXT LINK standby mode or recording, video
picture is from the AV2 input terminal irrespective of "AV1 Output"
setting.
RQT8020
21