Manually Programming Timer Recordings; Recording From Digital/Satellite Receiver Or Decoder - Panasonic Diga DMR-ES10 Operating Instructions Manual

Timer recording
Refer to the control reference on page 18.
You can enter up to 16 programmes up to a month in advance. (Each
daily or weekly programme is counted as one programme.)
Preparation
•
Turn on the television and select the appropriate video input to suit
the connections to this unit.
•
Check the time on the unit is correct.
Manually programming timer
recordings
RAM
-R -RW(V) +R
1
Press [PROG/CHECK].
For Continental Europe
TIMER
RECORDING
No. Name Date Start
01 ARD 15. 7. TUE 19:00
New Timer Programme
For Australia, N.Z., Asia and Middle East
TIMER
RECORDING
No. Name Date Start
01 ARD 15. 7. TUE 19:00
New Timer Programme
2
Press [e, r] to select "New Timer
Programme" and press [ENTER].
3
Press [q] to move through the items
and change the items with [e, r].
For Continental Europe
TIMER
RECORDING
Name Date Start
1 ARD 15. 7. TUE 19:00
For Australia, N.Z., Asia and Middle East
TIMER
RECORDING
Name Date Start
1 ARD 15. 7. TUE 19:00
•
Press and hold [e, r] to alter Start (Start time) and Stop
(Finish time) in 30-minute increments.
•
You can also set Name (Programme position/TV Station
Name), Date, Start (Start time), and Stop (Finish time) with
the numbered buttons.
•
You can also press [REC MODE] to change the recording mode.
•
Date
Date:
Daily timer:
Weekly timer: SUN
For Continental Europe
•
VPS/PDC (➔ page 18)
←→
ON OFF (---)
•
Programme Name
Press [w, q] to select "Programme Name" and press
[ENTER] (➔ page 34).
4
Press [ENTER].
For Continental Europe
TIMER
RECORDING
No. Name Date Start
01 ARD 15. 7. TUE 19:00
02 ARD 15. 7. TUE 22:00
New Timer Programme New Timer Programme
For Australia, N.Z., Asia and Middle East
TIMER
RECORDING
No. Name Date Start
01 ARD 15. 7. TUE 19:00
02 ARD 15. 7. TUE 22:00
New Timer Programme New Timer Programme
RQT8020
20
Repeat steps 2–4 to programme other recordings.
Remain 1:58 SP
12:56:00 15. 7. TUE
VPS Disc
Stop Mode
PDC space
20:00 SP - - - OK
Remain 1:58 SP
12:56:00 15. 7. TUE
Disc
Stop Mode
space
20:00 SP OK
Remain 1:58 SP
12:57:00 15. 7. TUE
VPS
Stop Mode PDC
20:00 SP - - -
Programme Name
Remain 1:58 SP
12:57:00 15. 7. TUE
Stop Mode
20:00 SP
Programme Name
Current date up to one month later minus
one day
→ →
SUN-SAT MON-SAT MON-FRI
→ →
--- SAT
Remain 1:58 SP
12:58:00 15. 7. TUE
VPS
Disc
Stop Mode
PDC space
20:00 SP - - - OK
Check to make sure "OK"
22:30 SP - - - OK
is displayed.
Remain 1:58 SP
12:58:00 15. 7. TUE
Disc
Stop Mode
space
20:00 SP OK
Check to make sure "OK"
22:30 SP OK
is displayed.
5
Press [z TIMER].
The unit turns off and "z" lights on the unit's display to
indicate timer recording standby has been activated.
RAM
Even if the unit is in timer recording standby, play starts when you
press [q] (PLAY) or [DIRECT NAVIGATOR]. Timer recording works
even during play.
■ To release the unit from recording standby
Press [z TIMER].
The unit turns on and "z" goes out.
•
Be sure to press [z TIMER] before the programme start time to
put the unit on recording standby. Timer recording will work only
if "z" is displayed.
■ To cancel recording when recording has
already begun
Press [z TIMER].
•
You can also press and hold [g] on the main unit for more than 3
seconds to stop recording.
Note
•
"z" flashes for about 5 seconds when the unit cannot go to timer
recording standby (e.g., a recordable disc is not in the disc tray).
•
If the unit is not put in the timer recording standby mode at the
latest 10 minutes before the programmed timer recording
starting time, the "z" flashes on the unit display. In this case,
press [z TIMER] to put the unit in the timer recording standby
mode.
•
When you programme successive timer recordings to start
immediately one after the other, the unit cannot record the part at
the beginning of the later programmes (a few seconds when
recording with DVD-RAM and approximately 30 seconds when
recording with DVD-R, DVD-RW (DVD-Video format) and +R).
For Continental Europe
Recording from digital/satellite receiver
or decoder
Preparation
•
Connect a digital/satellite receiver or decoder to this unit's input
terminals (➔ page 9).
•
When recording bilingual programmes
RAM
When both M 1 and M 2 is selected on the connected equipment,
you can select the audio type in playback.
-R -RW(V) +R
Select either M 1 and M 2 on the connected equipment. (The
selected audio only is recorded.)
•
When the output signal from the external equipment is NTSC,
change the "TV System" to "NTSC" in the SETUP menu
(➔ page 39).
1
While stopped
Press [INPUT SELECT] to select the
input channel for the equipment you
have connected.
e.g., If you have connected to AV2 input terminals, select "A2".
2
Press [REC MODE] to select the
recording mode.
3
Select the channel on the other
equipment.
4
Press [* REC].
Recording starts.
To skip unwanted parts
Press [h] to pause recording. (Press again to restart recording.)
To stop recording
Press [g].