Band Buttons; Tuning Buttons; Sel Button; Memory Button - Rotel RX-1052 Owner's Manual

Headphones Jack

This jack accepts a standard 1/4 inch ste-
reo headphone plug. Use an adaptor if your
headphones have a smaller plug.
: Inserting a headphone plug does not
NOTE
automatically disable the speaker outputs.
Use the SPEAKER buttons described in the
next section to turn the speakers on or off
during headphone listening.

Speaker Buttons

The RX-1052 provides output connections
for two pairs of speakers: A and B. Speaker
buttons on the front panel or remote control
allow you to activate the desired pair(s) of
speakers. Press the SPEAKER A button to ac-
tivate or deactivate the SPEAKER A outputs.
Press the SPEAKER B button to activate or
deactivate the SPEAKER B outputs.
An LED indicator located to the left of each
button lights when that speaker output is ac-
tivated.
: For private headphone listening, deac-
NOTE
tivate both the SPEAKER A and B outputs.

Input Buttons

Eight buttons on the right side of the front
panel directly select an audio or video in-
put source (PHONO, CD, TUNER, TAPE,
VIDEO 1, VIDEO 2, VIDEO 3, VIDEO 4) for
listening. The buttons are duplicated on the
remote, labeled PHO, CD, TUN, TP, V1, V2,
V3, and V4.
Push any of these buttons (or the duplicates
on the remote) to select the desired source.
You will hear this source and, if you have se-
lected a video source, see its picture on your
TV monitor. The front panel display shows the
current source selection.
The input source buttons can also be used
with the SEL button to select an input to be
available at the outputs for recording or for
use in remote zones.

ZONE Button

The ZONE button, on the front panel or re-
mote, serves as a standby button for the cur-
rently selected remote zone, toggling the zone
on or off. Select the desired zone using the
SEL button described below.
17
: Pressing the ZONE button without first
NOTE
specifying a zone with the SEL button, allows
Zone 2 control.
A long press of the ZONE button activates
the Party mode, selecting the source from the
main room for use by all of the remote zones
plus the record outputs.

SEL Button

Press the SEL button on the front panel or the
remote to select a zone for changing the input,
adjusting the volume, or turning a remote zone
on or off. Repeatedly press the button until
the desired zone appears in the front panel:
RECORD > ZONE 2 > ZONE 3 > ZONE 4
> MAIN. Once the desired zone appears,
you have 10 seconds to make the change.
Change the input selection by pressing an IN-
PUT button. When ZONES 2–4 appear, you
can also adjust the volume or turn the zone on
or off by pressing the ZONE button.
A long press of the SEL button is used to can-
cel the PARTY mode and return all zones to
their last previously selected inputs.

ZONE LED

The ZONE LED lights when a remote zone is
activated. The LED also flashes when engag-
ing Party Mode.

DISP Button

The DISP button on the remote toggles the
front panel display on or off.

LABEL Button

The LABEL button on the remote is used with
the ENTER button in programming custom
labels for the input buttons. These custom la-
bels appear in the front panel display when
an input is selected.

ENTER Button

The ENTER button on the remote serves two
functions.
To adjust the tone settings, repeatedly press
the ENTER button until BASS or TREBLE is
displayed. Then, use the CHARACTER +/–
buttons to increase or decrease the selected
tone setting.
The ENTER button is also used following the
press of the LABEL button in programming
custom labels.

BAND Buttons

Press the BAND button on the front panel or
the remote to toggle between AM and FM
reception.

TUNING Buttons

The TUNING buttons on the front panel or the
remote control provide two different tuning
functions, depending on the mode of opera-
tion: frequency tuning or preset tuning.

MEMORY Button

The front panel MEMORY button and the MEM
button on the remote are used with the NU-
MERIC buttons to store station presets.

NUMERIC Buttons

The NUMERIC buttons on the remote are
used to enter the number of a memorized
station preset or for direct entry of a station
frequency.
These buttons are also used for operating
Rotel CD and DVD players.

DIRECT Button

The DIRECT button on the remote is used with
the NUMERIC buttons for direct entry of a sta-
tion frequency in AM/FM tuning.

MONO Button

The MONO button on the front panel or the
remote toggles the FM mode from stereo re-
ception to mono reception.

TUNE/PRESET Button

T/P Button

The front panel TUNE/PRESET or remote con-
trol T/P button toggle between FREQUENCY
tuning and PRESET tuning modes.

CD/DVD Buttons

The STOP , PLAY , TRACK
RANDOM buttons on the remote are used for
operating Rotel CD and DVD players. They
are not used in operating the RX-1052.
English
, and