LG 50PY2DR Owner's Manual page 121

19. Color Temperature (Command2:u)
G To adjust color temperature.
You can also adjust color temperature in the Video
menu.
Transmission
[k][u][ ][Set ID][ ][Data][Cr]
Data 0: Medium 1: Cool 2: Warm
Acknowledgement
[u][ ][Set ID][ ][OK/NG][Data][x]
20. PIP Input Select (Command2:y)
G To select input source for sub picture in PIP/Twin pic-
ture mode.
Transmission
[k][y][ ][Set ID][ ][Data][Cr]
Data 0: DTV
1: Analog
2: Video
3: Front Video
Acknowledgement
[y][ ][Set ID][ ][OK/NG][Data][x]
21. ISM Method/Orbiter (Command2:p)
G To avoid having a fixed image remain on screen.
Transmission
[ j ][p][ ][Set ID][ ][Data][Cr]
Data 1: Inversion
2: Orbiter
4: White Wash
8: Normal
Acknowledgement
[p][ ][Set ID][ ][OK/NG][Data][x]
22. Low Power (Command2:q)
G To control the low power function on/off.
Transmission
[ j ][q][ ][Set ID][ ][Data][Cr]
Data 0: low power off
1: low power on
Acknowledgement
[q][ ][Set ID][ ][OK/NG][Data][x]
23. Orbiter Time Setting (Command2:r)
G To adjust orbiter operation time term.
Transmission
[ j ][r][ ][Set ID][ ][Data][Cr]
Data Min: 1 ~ Max: FE(*transmit by Hexadecimal code),
Unit: Second
Acknowledgement
[r][ ][Set ID][ ][OK/NG][Data][x]
24. Orbiter Pixel Setting (Command2:s)
G To adjust pixel number in orbiter function.
Transmission
[ j ][s][ ][Set ID][ ][Data][Cr]
Data Min: 1 ~ Max: 3
Acknowledgement
[s][ ][Set ID][ ][OK/NG][Data][x]
25. Tune Command (Command: m a)
G To tune channel to following physical/major/minor number
Transmission
[m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][ ][Data3][ ][Data4][ ][Data5][Cr]
Data 0: Physical Channel Number(Transmit by Hexadecimal code)
NTSC air:02~45
NTSC cable: 01, 0E~7D
ATSC air:01~45
ATSC cable:01~87
Data1,Data2: Major Channel Number (two part)/ Channel Number (One part)
Data1: High byte
Data2: Low byte
Two part channel number: Major number-Minor number
One part channel number: If the channel band is ATSC
digital cable, it can be used. In case of using one part chan
nel number, minor channel does not need.
Data3, Data 4: Minor Channel Number Data3: High byte Data4: Low byte
Data 5:
Two/One
Main/Sub
Part
7 6
5
Picture
Channel
Main Two
0 0
0
1
Sub 1
One 1
* All data are transmitted by Hexadecimal code
*Two/One part Channel: 6
This bit is used in a cable-ready system.
*Using physical channel: 5
If the channel band is NTSC air or NTSC cable, channel tun-
ing can be done by only physical channel. In this case, using
physical channel bit must be low(0).
But if the channel band is ATSC air or ATSC cable, there are
two cases that physical channel enable or disable.
If the physical channel sending is meaningful, you should set
this bit low(0). If the physical channel sending is meaningless,
you should set this bit high(1).
External Control Device Setup
Using 4
Physical Reserv
0
2 1
3
Channel ed
x 0
Use 0 0 0
No Use x
0 0 0 1
x
0 0 1 0
x 0 0 1 1
x
0 1 0 0
x 0 1 0 1
1
x 0 1
0
x 0 1 1 1
x
x x x x
x
1
1 1 1
bit
th
bit
th
Owner's Manual 121
Step
NTSC Air
NTSC Cable
ATSC Air
ATSC
Cable_std
ATSC
Cable_hrc
ATSC
Cable_irc
ATSC
cable_auto
Reserved
...
Reserved