Table of Contents
Advertisement
Specifying the Position Display Format
Normally, the watch displays a position obtained by a GPS measurement as
latitude and longitude values showing degrees, minutes, and seconds. You
can use the procedure below to specify display of latitudes and longitudes in
degrees and minutes only, or in degrees only. You can even specify display of
latitude and longitude in UTM grid coordinates.
To specify the position display format
1. In the Timekeeping or GPS Mode, press
2. Use K and L to select SET UP, and
3. Use K and L to move the cursor to
4. Press G to display the POS. FORM
L
5. Use K and L to select the position display option you want as described
in the table below.
When you want to display this:
Latitude and longitude in degrees, minutes, seconds
Latitude and longitude in degrees, minutes
Latitude and longitude in degrees
UTM coordinates
MGRS coordinates
Note
• If you select UTM for the position display format, you must also use UTM
coordinates when defining landmarks and AREA data.
6. After you are finished making the setting you want, press G to return to the
SET UP Screen.
7. Press MODE or MENU twice to return to the Timekeeping or GPS Mode.
Specifying the Distance, Speed, and Altitude Units
Use this procedure to specify the measurement units you want to use for display
of the distance, speed, and altitude values produced by GPS measurements.
To specify the distance, speed, and altitude units
1. In the Timekeeping or GPS Mode, press
2. Use K and L to select SET UP, and
3. Use K and L to move the cursor to
4. Use K and L to select DIST (distance),
L
5. Use K and L to cycle through the
Press K.
Item
DIST
km (kilometers)
SPD
km/h (kilometers per hour)
ALTI
m (meters)
6. Repeat steps 4 and 5 for other items if you want.
7. On the UNITS Screen, use K and L to move the cursor to DONE, and
then press G to return to the SET UP Screen.
• The measurement unit you specify affects the measurement range of each
item. See "Measurement Unit Conversion" for more information.
8. Press MODE or MENU twice to return to the Timekeeping or GPS Mode.
MENU twice to display the MENU
Screen.
then press G to display the SET UP
Screen.
POS. FORM.
Screen.
Select this option:
DEG.MIN.SEC
DEG.MIN
DEG
UTM
MGRS
MENU twice to display the MENU
Screen.
then press G to display the SET UP
Screen.
UNITS, and then press G to display the
UNITS Screen.
SPD (speed), or ALTI (altitude), and then
press G.
available units in the sequence noted
below, until the one you want to use is
displayed, and then press G.
Press L.
Units
mi (miles)
NM (nautical miles)
mi/h (miles per hour)
knot (knots)
ft (feet)
Clearing the Maximum Speed Record
The watch keeps a record of the maximum speed you attain when speed
measurements are being performed. Use the following procedure to clear the
maximum speed record when you want to start a new speed measurement, etc.
To clear the maximum speed record
1. While the Position Screen, Plot Screen,
2. Use K and L to move the cursor to
3. On the MAX SPD CLR Screen that
L
• To cancel the clear operation without
Specifying the Scale of the Plot Screen
Use the following procedure to change the scale of the Plot Screen.
To specify the scale of the Plot Screen
1. While the Plot Screen is on the display in
2. The cursor should already be located
3. Use K and L to cycle through the
L
• Pressing K makes the screen larger,
Press L.
Unit
km
0.5
1.0
2.0
mi, NM
0.2
0.5
1.0
• See "Specifying the Distance, Speed, and Altitude Units" for information
about specifying the measurement unit you want to use.
4. After you are finished, press G to save your setting and return to the Plot
Screen.
Turning Display of a Landmark Symbol On and Off
You can use the following procedure to turn display of specific landmark
symbols on (display) and off (not displayed). When a landmark symbol is
turned off, any landmark that is assigned that symbol does not appear on the
GPS Mode Plot Screen.
Note
• This procedure is impossible when there are no landmarks in the Landmark
List.
To turn display of a landmark symbol on and off
1. While the Plot Screen is on the display in
2. Use K and L to move the cursor to
3. Use K and L to select the landmark
L
4. Press G to toggle the display status of
• The initial default setting for all landmark
5. After everything is the way you want, use
• This saves your settings and returns to
2240-14
or Graphical Navigation Screen is on the
display in the GPS Mode, press MENU
to display the FUNCTION Screen.
MAX SPD CLR, and then press G.
appears, use K and L to move the
cursor to YES, and then press G to clear
the maximum speed record and return to
the Mode Screen you started from in
step 1.
clearing anything, move the cursor to NO
in the above step, and then press G to
return to the Mode Screen you started
from in step 1.
the GPS Mode, press MENU to display
the FUNCTION Screen.
next to ZOOM, so press G to display the
Scale Screen.
scale values in the sequence shown
below until the one you want to set is
displayed.
while L makes it smaller.
Press K.
Scale value
5.0
10
20
50
100
200
500
2.0
5.0
10
20
50
100
200
the GPS Mode, press MENU to display
the FUNCTION Screen.
DISP LMK (Display Landmark), and then
press G to display the DISP LMK
Screen.
symbol you want.
the selected landmark symbol on
(display) and off (do not display).
symbols is display off.
K and L to move the cursor to DONE,
and then press G.
the Plot Screen.
1000
500
Hide quick links:
Advertisement
Table of Contents
