Displaying A Landmark On A Map; To Create A New Route Plan On A Blank Route Plan Screen; About The Start Point Name; Creating A Route Plan - Casio 2240 Instruction Manual

Displaying a Landmark on a Map

The following procedure lets you select a landmark on the Landmark List and
display it on an on-screen map.
To display a landmark on a map
1. On the Landmark List, use K and L to
• Holding down either button moves the
2. Press MENU to display the FUNCTION
3. Use K and L to move the cursor to
• You can change the scale of the
Note
• See "Turning Display of a Landmark
(About 2 seconds)
L
4. After you are finished viewing the

Creating a Route Plan

• The Route Plan Screen of the watch lets you select a series of locations
from the Landmark List and plan a route from one point (start point) to
another point (destination). Each of the locations you pass through while
traveling, including your initial start point and final destination is called a
"waypoint," and a group of waypoints is called a "route."
• Before you start out on a hike or trip, you can input your planned route on
the watch by specifying a start point and up to nine more waypoints. Since
you must add waypoints to the Route Plan Screen by selecting them from
the Landmark List, the waypoints you want to use must already be
registered in the Landmark List. After adding a waypoint from the Landmark
List, you can edit its data record if you want.
• The following procedures explain how to put together a route, and how to
add, insert, edit, and delete waypoints.
Note
• Editing or deleting a landmark in a Route Plan does not affect the
corresponding data in the Landmark List.
To display the Route Plan Screen
1. In the Timekeeping or GPS Mode, press
2. Use K and L to move the cursor to
3. Press MODE twice to return to the
L
Creating a New Route Plan
Use the following procedure when you want to put together a new route. Later
you can edit the contents of a route plan by changing the order of the
waypoints, inserting new waypoints, etc.
move the cursor to the landmark you
want.
cursor at high speed.
Screen.
SHOW MAP, and then press G to display
the Landmark Map Screen.
Landmark Map Screen by pressing K (to
decrease the scale value and zoom in)
and L (to increase the scale value and
zoom out).
Symbol On and Off" for information about
displaying other landmarks in the vicinity
of the current landmark, and "Turning a
Track Point's Display Status On and OFF"
for information about displaying
waypoints, and track points.
Landmark Map Screen, press G or
MODE to return to the Landmark List.
MENU twice to display the MENU
Screen.
WAY POINT, and then press G to display
the Route Plan Screen.
Timekeeping or GPS Mode.

To create a new route plan on a blank Route Plan Screen

1. On the Route Plan Screen, the cursor
• If your Landmark List does not have any
2. Use K and L to select the landmark
• This returns to the Route Plan Screen
3. Use K and L to move the cursor to
4. Use K and L to select the landmark you want to define for your next
waypoint, and then press G to register it and return to the Route Plan
Screen.
5. Repeat steps 3 and 4 for the rest of the waypoints you want to specify for
your route plan.
• Basically, you should specify waypoints in the sequence you plan to pass
them (first waypoint first, second waypoint second, etc.) You will, however,
be able to change a route plan using the procedures that follow this one.
• A route plan can have one start point, and up to nine other waypoints.

About the Start Point Name

• The start point name appears as "S:_____" if there is currently no route
defined on the Route Plan Screen.
• If the start point name has more than seven characters, it scrolls on the
display from right to left.
To view a waypoint's record data
1. On the Route Plan Screen, use K and
2. Press G to display the selected
• The record data of a waypoint includes
K
3. After you are finished, press G again to
L
Editing Your Route Plan
Use the following procedures when you want to change the order of the
waypoints in your route plan, insert new waypoints, delete waypoints, etc.
To change a waypoint to a different one
1. On the Route Plan Screen, use K and
2. Press MENU to display the FUNCTION
3. The cursor should already be located
4. Use K and L to move the cursor to the
L
5. On the CHANGE? confirmation screen that
• To cancel the change operation without
2240-11
should already be located next to
"S:_____" (start point), so press G to
display the Landmark List.
landmarks, the message "NO DATA"
appears for about two seconds, and then
the Route Plan Screen reappears.
you want to define as the start point of
your route plan, and then press G.
with the landmark you selected shown for
the start point of your route plan.
" :_____", and then press G to display
the Landmark List.
L to move the cursor to the start point
name or the name of the waypoint whose
record data you want to view.
waypoint's record data screen.
latitude, longitude, and altitude.
return to the Route Plan Screen.
L to move the cursor to the waypoint
you want to change.
Screen.
next to CHANGE, so press G to display
the CHANGE W.P Screen.
new waypoint you want to use, and then
press G.
appears, use K and L to move the
cursor to YES, and then press G to change
the waypoint you selected in step 1 and
return to the Route Plan Screen.
changing anything, move the cursor to NO
in the above step, and then press G to
return to the Route Plan Screen.