Circuit Breaker Instructions; Grounding Instructions; Grinding Tips; Unpacking Instructions - Cabela's 08-2201 Instruction Book

CIRCUIT BREAKER INSTRUCTIONS

This Grinder is equipped with a Circuit
Breaker as a safety precaution. If the Grinder
should stop running follow these steps to
remedy:
1. Turn the Grinder to the "Off" position.
2. Press the Circuit Breaker Reset Button
.
(Figure 19)
3. Turn the Grinder back on and resume
grinding.
4. If the Grinder still does not turn on, check that the electrical wall outlet is properly
working. Plug in another appliance to see if that appliance works from the wall outlet.
Check that the household circuit breaker has not been tripped. If none of the above
steps remedy the situation, or if the Circuit Breaker repeatedly shuts off the Grinder
contact a customer service for further assistance.
WARNING!
DO NOT continue to use the Grinder if the Circuit Breaker trips
repeatedly. Continued use may cause permanent damage to the Grinder and will void
the warranty.
PLEASE NOTE:
This Grinder features an all hardened steel gear
transmission. This causes the Grinder to operate at a higher volume and
temperature than other Grinders.
Grinder's performance.

GRINDING TIPS

.
DO NOT over-tighten the Front Ring Nut. It should be firmly tight.
.
Make sure the Grinding Knife blades lay flat on the Grinder Plate.
.
DO NOT operate the Grinder without meat in the Head. Running the Grinder
while dry could damage the Head and Auger.
.
Always lubricate the Head, Grinding Plate and Grinding Knife with a food-grade
silicone spray after cleaning.
.
DO NOT grind bones, nuts or other hard objects.
.
If the Grinder Plate becomes clogged during operation, follow these steps to
restore normal output.
.
Turn the Grinder "OFF" and disconnect the Power Cord from the electrical outlet.
.
Remove the Front Ring Nut and Grinding Plate.
.
Thoroughly clean the Grinding Plate. Make sure all of the holes are clear.
.
Re-install the Grinding Plate and Front Ring Nut.
.
Re-connect the Grinder to the electrical outlet.
.
Continue with grinding.
.
Repeat as necessary.
FIGURE 19
Circuit Breaker
Reset Button
This is normal and will not affect the
-18-

GROUNDING INSTRUCTIONS

GROUNDING
This appliance must be grounded while in use to protect
the operator from electrical shock.
is equipped with a 3-conductor cord and a 3-prong
grounding type plug to fit the proper grounding-type
receptacle. The appliance has a plug that looks like
Figure A. An adaptor, Figure B, should be used for
connecting Figure A plugs to two-prong receptacles.
The grounding tab which extends from the adaptor must
be connected to a permanent ground such as a properly
grounded outlet box as shown in Figure C using a metal
screw.
EXTENSION CORDS
Use only 3-wire extension cords which have 3-prong
grounding-type plugs and a 3-pole cord connector
that accepts the plug from the appliance. Use only
extension cords having an electrical rating not less than
the rating of the appliance. DO NOT use damaged
extension cords. Examine extension cord before using
and replace if damaged. DO NOT abuse extension
cord and do not yank on any cord to disconnect. Keep
cord away from heat and sharp edges.

UNPACKING INSTRUCTIONS

.
Remove all parts from packaging material and check to be sure there are no
missing parts.
.
Retain packaging material for storage of the Grinder and Grinder parts when not
in use.
If you are missing any parts, or if any parts are damaged, contact
Cabela's Customer Service- Retail Store Purchases 1-800-905-2731 (U.S. & Canada) /
Catalog & Internet Purchases: 1-800-237-8888 / All International: 1-308-234-5555
Circuit
Grounding
The appliance
Conductor
Grounding
Prong
Metal
Grounding
Screw
Cover of
Grounded
Outlet Box
Grounding
Means
AA2220
-7-
Figure A
Figure B
Figure C