Blocking Channels; Unlocking Programs Temporarily; Locking Video Inputs - Toshiba 56MX195 Owner's Manual

Blocking channels

With the Channels Block feature, you can block specific
channels. You will not be able to tune blocked channels unless
you clear the setting first.
To block channels:
1. Press MENU and highlight the Locks menu icon.
2. Press z to display the
PIN code entering
screen.
3. Enter your four-digit
PIN code and press
ENTER (see page 93 for
details).
4. Press z to highlight
Channels Block and then press ENTER.
5. Using the yz x • buttons, select the input for which you
want to change the rating limits (ANT1, ANT2, or Cable
Box, if connected) and press ENTER.
A list of the channels available for that input will be
displayed along with the call letters for each channel, if
available.
6. Press yz to highlight
the channel you want to
block, then press
ENTER, which puts an
"×" in the box next to
that channel.
7. Repeat step 6 for other
channels you want to
block.
8. Highlight Done and press ENTER.
To unblock individual channels:
In step 6 above, press yz to highlight the channel you want to
unblock, and then press ENTER to remove the "×" from the
box, and highlight Done, and then press ENTER.
To block all channels at once:
Highlight Block All in step 6 above, and then highlight Done,
and press ENTER.
To unblock all locked channels at once:
Highlight Allow All in step 6
above, and then highlight
Done, and press ENTER.
Note: Channel blocking may not take effect if you have a cable box
connected and use the cable box controls to change channels.
Downloaded from www.Manualslib.com
Chapter 9: Using the Locks menu
Locks
Enable Rating Blocking
Off
Edit Rating Limits
Channels Block
Input Lock Off
Front Panel Lock Off
Game Timer Off
New PIN Code
Navigate Back
Select CH RTN
Channels Block
1
2
3
4
5
6
7
8
9
10
Channels Block
1
2
3
4
5
6
7
8
9
10
Copyright © 2005 TOSHIBA CORPORATION. All rights reserved.
manuals search engine

Unlocking programs temporarily

If you try to watch a TV program that exceeds the rating limits
you set, the TV enters program lock mode. You can either
unlock the program temporarily or select a non-locked program
to watch.
To temporarily unlock the program:
1. Press MUTE.
2. Enter your four-digit PIN code and press ENTER. If the
correct code is entered,
the program lock mode
is released and the
Exit
EXIT
normal picture appears.
All locking is disabled
until the TV is turned
off, and will be enabled
when the TV is turned on again.

Locking video inputs

ANT 1
You can use the Input Lock feature to lock the video input
ANT 1
sources (VIDEO 1, VIDEO 2, VIDEO 3, ColorStream HD-1,
ANT 2
ColorStream HD-2, HDMI 1/HDMI 2, PC) and channels 3
Cable Box
and 4. You will not be able to view the input sources or channels
until you turn off the input lock.
Allow All
To lock the video inputs:
Block All
Cancel
1. Press MENU and highlight the Locks menu icon.
Done
2. Press z to display the PIN code entering screen.
3. Enter your four-digit PIN code and press ENTER.
4. Press z to highlight Input Lock and press •.
5. Press y or z to select the level of video input locking you
prefer, as described below:
Video: Locks VIDEO 1,
VIDEO 2, VIDEO 3,
ColorStream HD1/
HD2, HDMI 1/
HDMI 2, and PC.
Video+: Locks VIDEO
ANT 1
1, VIDEO 2, VIDEO 3,
ANT 1
ColorStream HD1/
ANT 2
HD2, HDMI 1/
Cable Box
HDMI 2, PC and channels 3 and 4. Select Video+ if you
use the antenna terminal to play a video tape.
Allow All
Note: Make sure the POP is not on channel 3 or 4.
Block All
Off: Unlocks all video input sources.
Cancel
Done
6. Press ENTER.
Note: When a CableCARD™ is inserted, Video+ will behave the same as
Video lock.
Locks Active
Enter PIN code to temporaily un-
block.
* * * *
Cancel Done
Locks
Enable Rating Blocking Off Off
Edit Rating Limits Video
Channels Block
Video +
Input Lock Off
Front Panel Lock Off
Game Timer Off
New PIN Code
Navigate Back Exit
Select CH RTN EXIT
99