Husqvarna SpeedMill K750 Operator's Manual And Spare Parts List
Hide thumbs
Also See for SpeedMill K750:
- Operator's manual (24 pages) ,
- Operator's manual (12 pages) ,
- Operator's manual (24 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Husqvarna SpeedMill K750
Summary of Contents for Husqvarna SpeedMill K750
- Page 1 It is the owner’s responsibility to ensure that all operators of this machine have read and understood the content of this manual be- fore using the product! Careless or improper use of this machine can cause serious or even fatal injury! Allow only competent adults to operate this machine!
-
Page 2: Table Of Contents
Husqvarna. Per assistenza, rivolgersi al rappresentante di zona della Husqvarna Construction Products. För service på platsen, kontakta din lokala representant för Husqvarna Construction Products. Para obter serviço técnico local, contactar o representante da Husqvarna Construction Products Husqvarna Construction Products, North America... - Page 4 DO NOT operate the machine until you have consulted an experienced operator. If you have further questions you can contact the closest Husqvarna Contruction Products location by writing or calling, see information below. You can also find the closest location by searching the inter- net at: www.husqvarnacp.com.
-
Page 5: Safety Instructions
SAFETY INSTRUCTIONS WARNING! Read, understand, and follow all warnings and instructions both manuals. Failure to do so may result in serious personal injury as well as damage to the equipment. It is not possible to cover all potentional risk situations that can arise from pipe cutting and beveling within these instructions. -
Page 6: What Is What
WHAT IS WHAT WHAT IS WHAT (PARTS IDENTIFICATION) E. SpeedMIll Hub Nut: Designed specifically for the SpeedMill. Holds SpeedMill accesories in position. A. SpeedMill BLADE GUARD: Designed specifically for Read this Operation Manual for more information. See the SpeedMill. One side is open to allow mounting of the SpeedMill Spare Parts List in this document for part num- SpeedMill Bowls. -
Page 7: Uses
USES, TOOLS, AND ASSEMBLY Uses: Cutting and beveling of waste/sewer and supply Verify that 1” (25.4mm) adapter (P/N water PVC pipe with the proper beveling accessory. Note 506 37 96-25) is pushed onto blade this machine is not for cutting and beveling of any non-plas- shaft so it contacts the inner flange. -
Page 8: Assembly
ASSEMBLY AND OPERATION Assembling the bevelling ring to the Assembling the bevelling bowls to SpeedMill. the SpeedMill. Ring Beveler Bowl Bevelers 506 11 96-01 for: 506 11 97-01 for: Sewer/Drain 10” to 36” in diameter. Waste/Sewer/Drain 4” to 8” in diameter. Supply/Water 4”... -
Page 9: Operation
OPERATION WARNING! Rotate pipe and repeat this EVACUATE PIPE CONTENTS cutting process until pipe before cutting or EXPLOSION circumference is cut. else an may occur! Static electricity from cutting operation may cause gas or other pipe contents to explode. Position plastic pipe so pipe end is Bevel Pipe: off the ground. -
Page 10: Maintenance
MAINTENANCE MAINTENANCE: CONVERTING THE SPEEDMILL TO A REGU- LAR POWER CUTTER. The guard on the SpeedMill is designed to work together CAUTION! with the special outer flange and SpeedMill Bowls used Allow SpeedMill Bowls to cool before performing any main- on the SpeedMill. -
Page 12: Pipe Application Chart
Pipe Application Chart Husqvarna Speedmill II - Bowl & Ring Bevelers Application Chart Classes of Pipe CIOD IPS ASTM D2241 SDR 35 SDR 26 C900 C900/905 SDR 26 SDR 21 Sizes 4" 506119701 6" Bowl Bevelers 8" 10" 12" 506119601 14"... -
Page 13: Operator Tips
Husqvarna Speedmill Operators Tip Sheet 1. Bowl abrasive cleaning - The bowls will gather PVC dust usually in the outer bowl which is not being used. For instance if the 4” bowl is used a lot, the 6” bowl will accumulate dust on the abrasive. - Page 14 525 24 82-01 12 SpeedMill 2008-09...