Husqvarna K750 Operator's Manual
Husqvarna cut-off saw operator's manual
Hide thumbs
Also See for K750:
- Operator's manual (24 pages) ,
- Operator's manual and spare parts list (14 pages) ,
- Operator's manual (12 pages)
Related Manuals for Husqvarna K750
Summary of Contents for Husqvarna K750
- Page 1 Operator′s manual K750 Please read the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h...
-
Page 2: Key To Symbols
Key to symbols WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Always wear: •... -
Page 3: Table Of Contents
Contents KEY TO SYMBOLS Key to symbols ... CONTENTS Contents ... WHAT IS WHAT? What is what on the power cutter? ... SAFETY INSTRUCTIONS Steps before using a new power cutter..Personal protective equipment ... Machine′s safety equipment ... Checking, maintaining and servicing the machine′s safety equipment ... -
Page 4: What Is What
What is what on the power cutter? 1 Front handle 2 Water tap 3 Warning decal 4 Air filter cover 5 Cylinder cover 6 Choke 7 Throttle lockout 8 Throttle control 9 Start throttle lock 10 Stop switch 11 Starter handle 12 Starter 13 Muffler 4 –... -
Page 5: Safety Instructions
Do not use the power cutter if the idle speed is not adjusted correctly! • Let your Husqvarna dealer regularly check the power cutter and make essential adjustments and repairs. WARNING! Under no circumstances may the design of the machine be modified without the permission of the manufacturer. -
Page 6: Machine's Safety Equipment
SAFETY INSTRUCTIONS Machine′s safety equipment This section describes the machine′s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ”What is what?” section to locate where this equipment is positioned on your machine. -
Page 7: Checking, Maintaining And Servicing The Machine's Safety Equipment
SAFETY INSTRUCTIONS Checking, maintaining and servicing the machine′s safety equipment WARNING! All servicing and repair work on the machine requires special training. This is especially true of the machine′s safety equipment. If your machine fails any of the checks described below you must contact your service agent. -
Page 8: General Safety Precautions
Contact your local petrol station to find out where to dispose of excess fuel. • Always use a Husqvarna fuel container with an anti-spill valve. WARNING! Bear in mind the risk of fire, explosion and inhaling fumes. Stop the engine before fuelling. -
Page 9: General Working Instructions
SAFETY INSTRUCTIONS General working instructions WARNING! This section describes basic safety directions for using a power cutter. This information is never a substitute for professional skills and experience. If you get into a situation where you feel unsafe, stop and seek expert advice. Contact your dealer, service agent or an experienced power cutter user. -
Page 10: How To Avoid Kickback
SAFETY INSTRUCTIONS • Move the blade slowly forwards and backwards to achieve a small contact area between the blade and the material to be cut. This reduces the temperature of the blade and ensures effective cutting. • Feed down the machine in line with the blade. Pressure from the side can damage the blade and is very dangerous. -
Page 11: Cutting Blades
SAFETY INSTRUCTIONS Pinching/rotation If the cut is pressed together this can lead to jamming. The machine can be pulled down suddenly with a very powerful jerk. How to avoid pinching Support the work piece in such a way that the cut remains open during the cutting operation and when the cut is finished. -
Page 12: Diamond Blades
SAFETY INSTRUCTIONS Ensure the blade it not cracked or damaged in any other way. Test the abrasive disc by hanging it on your finger and tapping it lightly with a screwdriver or the like. If the disc does not produce a resonant, ringing sound it is damaged. Diamond blades Diamond blades consist of a steel body provided with segments that contain industrial diamonds. -
Page 13: Assembly
Do not use warped, notched, indented or dirty flange washers. Do not use different dimensions of flange washers. Fitting the cutting blade Husqvarna’s blades are approved for hand-held power cutters. Blades are manufactured with three different diameters of centre holes: 20 mm (0.787"), 22.2 mm (7/8") and 25.4 mm (1"). -
Page 14: Fuel Handling
This gives rise to a high engine temperature, which can result in serious engine damage. Two-stroke oil • For best results and performance use HUSQVARNA two- stroke engine oil, which is specially formulated for our air- cooled two-stroke engines. •... -
Page 15: Starting And Stopping
STARTING AND STOPPING Starting and stopping WARNING! Note the following before starting: Do not start the power cutter without the belt guard fitted. Otherwise the clutch could come loose and cause personal injuries. Always move the machine away from the refuelling area before starting. -
Page 16: Maintenance
Tensioning the drive belt • The drive belt is fully enclosed and well protected from dust and dirt. • When the drive belt is to be tensioned, release the bolts holding the cutting arm. • Screw the adjuster screw so that the square headed nut comes opposite the marking on the cover. -
Page 17: Fuel Filter
In order to obtain a good filtering effect, the filter must be replaced regularly or cleaned and oiled. A special HUSQVARNA oil has been produced for this purpose. Remove the foam plastic filter. Wash the filter well in tepid soapy water. After cleaning, rinse the filter well in clean water. - Page 18 • Pull the cord out about 30 cm and lift it into the cut-out in the periphery of the starter pulley. When the cord is intact: Release the spring tension by letting the pulley rotate slowly backwards. Remove any remnants of the old starter cord and check that the return spring works.
-
Page 19: Spark Plug
Fitting the starter • To fit the starter, first pull out the starter cord and place the starter in position against the crankcase. Then slowly release the starter cord so that the pulley engages with the pawls. • Tighten the screws. Spark plug The spark plug condition is influenced by: •... -
Page 20: General Maintenance Instructions
MAINTENANCE General maintenance instructions Below you will find some general maintenance instructions. If you have more questions, contact your service agent. Daily maintenance 1 Check that the components of the throttle control work smoothly (throttle control and throttle trigger lock). 2 Check the tension of the drive belt. -
Page 21: Technical Data
1/2 idling and 1/2 max speed. Cutting equipment Cutting blade Max. peripheral speed, m/s 12” (300 mm) 14” (350 mm) TECHNICAL DATA K750 2700 9300 (+/- 150) 3,7/9000 Champion RCJ 6Y Zama 12” (300 mm) ) in conformity with EC directive 2000/14/EC. -
Page 22: Ec-Declaration Of Conformity
Husqvarna Construction Products, SE-433 81 Partille, Sweden, tel: +46-31-949000, declares under sole responsibility that the power cutter K750 from year 2006 serial numbers and onward (the year is clearly stated in plain text on the rating plate with subsequent serial number) conforms with the requirements of the COUNCIL’S DIRECTIVE: •... - Page 24 1150287-26 ´®z+R<h¶6(¨ ´®z+R<h¶6(¨ 2006-11-23...