Memory Reset; Remote Control Code - Panasonic SC-HC27 Operating Instructions Manual

Disc
Display not shown correctly.
Playback does not start.
• You did not put the disc in correctly. Put it in correctly.
• Disc is dirty. Clean the disc.
• Replace the disc if it is scratched, warped, or
non-standard.
• There is condensation. Let the system dry for 1 to 2 hours.
USB
The USB device or the contents in it cannot be read.
• The format of the USB device or the contents in it is/are
not compatible with the system.
• USB devices with storage capacity of more than 32 GB
cannot work in some conditions.
Slow operation of the USB device.
• Large content size or large memory USB device takes
longer time to read.
The elapsed time shown is different from the actual play
time.
• Transfer the data to another USB device or backup the
data and reformat the USB device.
Radio
A beat sound is heard.
• Switch off the TV or move it away from the system.
• Move mobile telephones away from the unit if the
interference is apparent.
A low hum is heard during AM broadcasts.
• Move the antenna away from other cables and cords.
Stations cannot be selected.
• Change the AM frequency step (Z page 8).
Main unit displays
"--:--"
• You connected the AC mains lead for the first time or there
was a power failure recently. Set the clock.
"ADJUST CLOCK"
• Clock is not set. Adjust the clock accordingly.
"ADJUST TIMER"
• Play timer is not set. Adjust the play timer accordingly.
"ERROR"
• An incorrect operation was done. Read the instructions
and try again.
"F61"
• There is a power supply problem.
"IPOD OVER CURRENT ERROR" or
"USB OVER CURRENT ERROR"
• The iPod/iPhone or USB device is drawing too much
power. Remove the iPod/iPhone or USB device. Switch
the system off and on again.
"NODEVICE"
• The iPod/iPhone or USB device is not connected.
Examine the connection.
10
"NO DISC"
• You have not put in a disc.
10
"NO PLAY"
• You have put in a disc that the system cannot play.
• You have inserted a USB device that cannot be played.
Examine the content. You can only play supported format.
• If there are more than 255 albums or folders (audio
and non-audio), some of the MP3 files in these albums
cannot be read and played. Transfer these music albums
to another USB device. Alternatively, reformat the USB
device and save these music albums prior to saving the
other non-audio folders.
"NOT MP3/ERROR"
• An unsupported MP3 format. The system will skip that
track and play the next one.
"NOT SUPPORTED"
• You have inserted an iPod/iPhone that cannot be played.
• If the iPod/iPhone is compatible, remove the iPod/iPhone
and connect it again. Examine that the battery of the iPod/
iPhone is not depleted.
"REMOTE " ("  " stands for a number.)
• The remote control and this unit are using different codes.
Change the code of the remote control.
– When "REMOTE 1" is shown, press and hold [OK] and
[T] for a minimum of 4 seconds.
– When "REMOTE 2" is shown, press and hold [OK] and
[R] for a minimum of 4 seconds.
"–VBR–"
• The system cannot show the remaining play time for
variable bit rate (VBR) tracks.
Memory reset (initialisation)
Reset the memory when the following situations occur:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.
1
Disconnect the AC mains lead.
Wait 3 minutes before you continue with step 2.
2
While you press and hold [1] on the main unit,
connect the AC mains lead again.
"– – – – – – – –" is shown.
3
Release [1].
All the settings are set back to the factory preset.
It is necessary to set the memory items again.

Remote control code

When other Panasonic equipment responds to the remote
control of this system, change the remote control code for
this system.
To set the code to "REMOTE 2"
1
Press and hold [CD] on the main unit and [R] on the
remote control until "REMOTE 2" is shown.
2
Press and hold [OK] and [R] for a minimum of
4 seconds.
To set the code to "REMOTE 1"
1
Press and hold [CD] on the main unit and [T] on the
remote control until "REMOTE 1" is shown.
2
Press and hold [OK] and [T] for a minimum of
4 seconds.