Millivolt Appliance Checkout; Small Area Paint Touch-Up - Lennox Hearth Products CI1500DVF Series Homeowner's Care And Operation Instructions Manual

6. Install the left top twig onto the corre-
sponding pin on the rear log and align it
with the indentation on the front left log
as shown in Figure 14.
Left Top
Twig
Figure 14
7. Install the center top twig onto the cor-
responding pin on the rear log and align
it with the indentation on front left log as
shown in Figure 15.
Figure 15
8. Install the front right twig onto the cor-
responding pin on the right front log. Align
the twig with the indentation on the front
right log as shown in Figure 16.
Right
Front Twig
Figure 16
9. Place the glowing embers on the burner
as shown in Figures 17 and 18.
One package of ember material has been
included with this log set You will not need
to use the entire bag.
IMPORTANT: The quantity and place-
ment of the ember material can affect
stove performance therefore it is very
important that it be placed as shown in
Figures 17 and 18.
8
a. Unpackage and divide the fi ne ember mate-
rial (mineral wool) into dime-sized fl uffy
pieces.
b. Distribute the ember pieces over the top of the
front burner ports. Avoid covering the slots
and fi lling the area in front of the forward
logs (see Figures 17 and 18).
Embers
Figure 17
DO NOT PLACE EMBERS ON TOP
Center
OF THE BURNER SLOTS.
Top Twig
Figure 18
SIT MILLIVOLT APPLIANCE CHECKOUT
The pilot fl ame should be steady, not lifting
or fl oating. Flame should be blue in color with
traces of orange at the outer edge. The top 3/8"
(10 mm) at the pilot generator (thermopile)
and the top 1/8" minimum (tip) of the quick
drop out thermocouple should be engulfed
in the pilot fl ame. The fl ame should project 1"
(25 mm) beyond the hood at all three ports
(Figure 19).
Replace logs if removed for pilot inspec-
tion.
To light the burner, rotate the gas valve control
knob counterclockwise to the "ON" position
then turn "ON" the on/off rocker switch.
NOTE: DIAGRAMS AND ILLUSTRATIONS ARE NOT TO SCALE.
Proper Pilot Flame Appearance
MILLIVOLT Hood Igniter Rod
Thermocouple
Pilot
Nozzels
Thermopile
Figure 19
With proper care and maintenance, your appli-
ance will provide many years of enjoyment. If
you should experience any problem, fi rst refer
to the troubleshooting guide in this manual.
If problem persists, contact your Lennox
distributor.

SMALL AREA PAINT TOUCH-UP

Models with Black Painted Finish
The stove body is painted with a quality high-
temperature stove paint. Only use factory sup-
plied Stove Paint for touch-ups (70K99).
Using one small piece of 320 grit sand paper
and lightly sand the blemish so that the edges
are "feathered" or smooth to the touch between
the painted and bare sur-faces. Do not let the
sand paper gum up with paint, as this will cause
scratches on the metal surface. If there are any
scratches, use 600 grit sandpaper instead. Mask
off surfaces you do not want painted. Paint
lightly over the bare surface fi rst as this will
act as an under-coat. Then paint over a larger
area in smooth even strokes to blend.
See Burn-In Period on Page 4 for information
on curing the paint.
SMALL AREA TOUCH-UP PAINT
Models with Enamel Finish
If the enamel fi nish on your stove becomes
chipped, it can be touched up using the
enamel touch-up paint. Follow instructions on
tube for applying. See Page 16 for ordering
information.
Note: When enamel is heated to high tempera-
tures it is subject to crazing (a very fi ne and
random network of hairline cracks on the surface
of the porcelain). Crazing is a normal occurrence
when enamel is exposed to high temperatures.
Your enamel fi nish will not be harmed nor will
the function of the stove be impaired.
3/8" Min.
(9 mm)