Page 2
How can you get in touch with Invacare®? If you have any questions or need support, please contact your authorised Invacare® Dealer, who has the necessary know-how and equipment plus the special knowledge concerning your Invacare® product, and can offer you all-round satisfactory service. Should you wish to contact Invacare® directly, you can reach us in Europe at the following addresses and phone numbers.
Page 3
Invacare® AS Grensesvingen 9 0603 Oslo Norge (Kundeservice): +47 - 22 57 95 10 Fax (Kundeservice): +47 - 22 57 95 01 Invacare® PORTUGAL Lda Rua Senhora de Campanhã, 105 4369-001 Porto PORTUGAL +352-225105946 Fax: +352-225105739 Invacare® n.v. Autobaan 14...
Table of Contents Chapter Introduction ...9 Important symbols in this manual ...11 Type Classification and Area of Use ...11 Safety Notes...12 General Safety Notes ...12 Safety information with regard to care and maintenance ...15 Safety Information on Electromagnetic Interference ...16 Safety Information on Driving and Freewheel Mode ...17 Safety Information on Wheelchairs with a Lifter ...19 Safety Information on Wheelchairs with Recaro Seats ...20...
Page 5
7.2.2 Status Display...31 7.2.3 Multi-Purpose Display...31 7.2.4 Symbols shown on the Multi-Purpose Display and their meanings...32 7.2.5 Joystick ...33 7.2.6 Socket for Programmer...33 7.2.7 Charging Socket ...34 7.2.8 Connection Socket for Supply Cable (Bus Cable)...34 Operating the Joystick Box ...35 7.3.1 Switching the Joystick Box ON/OFF...35 7.3.2...
Page 6
Adjusting the pommel: ...60 Recaro Seats ...61 9.2.1 Recaro "N-Joy" and "Miles" (mechanically adjustable) ...61 9.2.2 Recaro Ergomed DS (electrically adjustable):...62 Invacare® Ultimate and Personal Special Seating Systems...63 9.3.1 Adjusting the seat tilt...63 9.3.2 Seat version: Personal...64 9.3.2.1 Adjusting the height of the back ...64 9.3.2.2...
Page 7
10.2.2 Manually Adjustable Legrest ...80 10.2.2.1 Removing the Legrest...81 10.2.2.2 Height Adjustment for Ergonomic Length Compensation ...82 10.2.2.3 Manually adjustable legrest: Angle Adjustment...83 10.2.2.4 Manually adjustable legrest: Adjusting the Length ...84 10.2.2.5 Manually adjustable legrest: Adjusting the Angle of the Footplate...84 10.2.3 Electrically Adjustable Legrest...85 10.2.3.1...
Page 8
13.2.1 Repairing a flat tyre (pneumatic tyres type 200 x 50)...109 13.2.2 Repairing a flat tyre (pneumatic tyres type 3.00x4")...111 13.2.3 Repairing a flat tyre (pneumatic tyres type 3.00-8") ...113 Care and maintenance ...115 Transport...118 15.1 Transferring the wheelchair to another vehicle...118 15.2 Securing the wheelchair for transport...118 15.2.1...
Introduction Dear Customer, First we would to thank you for choosing an Invacare® product. We hope you will be satisfied with your new Powerchair and that it will bring you much enjoyment. This wheelchair combines attractive design with a new dimension in mobility and driving pleasure.
Page 10
The individually programmable Invacare® Advanced Control System (ACS) allows fine-tuning of all driving characteristics. The compact design guarantees excellent manoeuvrability and easy transport. Thanks to a well thought-through concept, most special design requirements can be easily taken care of at the time of prescription. Later retro-fitting is possible, however this requires more work and should be performed by trained personnel.
Important symbols in this manual WARNING: This symbol warns you of danger! Follow the instructions to avoid injury to the user or damage to the product! NOTE: This symbol indicates hints and suggestions which should help make operating the product easier and point out special functions.
Safety Notes READ WELL BEFORE OPERATION! General Safety Notes Danger of injury if wheelchair is used in any other way than the purpose described in this manual! Adhere strictly to the instructions in this User's Manual! Danger of injury if the wheelchair is driven when ability to operate a vehicle is impaired by medication or alcohol! Never drive the wheelchair under the influence of medication or alcohol! Danger of damage or injury if wheelchair is accidentally set into motion!
Page 13
Danger of injury if the On/Off Button is pressed while the wheelchair is in motion, due to it coming to an abrupt, sharp stop! If you have to brake in an emergency, simply release the joystick which will bring you to a halt! Danger of injury when transferring wheelchair to another vehicle for transport with the occupant seated in it!
Page 14
Danger of fire or breaking down due to electric devices being connected! Do not connect any electric devices to your wheelchair that are not expressly certified by Invacare® for this purpose! Have all electrical installations done by your authorised Invacare® Dealer!
Safety information with regard to care and maintenance Danger of accident and loss of guarantee if maintenance is insufficient! For reasons of safety and in order to avoid accidents which result from unnoticed wear, it is important that this electric vehicle undergoes an inspection once every year under normal operating conditions (see inspection plan contained in service instructions)! Under difficult operating conditions such as daily travel on steep slopes, or in the case of use in medical care cases with frequently changing wheelchair users, it would be expedient to...
Safety Information on Electromagnetic Interference This electric vehicle was successfully tested in accordance with International standards as to its compliance with Electromagnetic Interference (EMI) Regulations. However, electromagnetic fields, such as those generated by radio and television transmitters, and cellular phones, can influence the functions of electric vehicles.
Safety Information on Driving and Freewheel Mode Danger of injury if the wheelchair tips over! Only ever negotiate gradients of up to the maximum defined in the Technical Specifications and only with the backrest and seat tilt in an upright position! Only ever drive downhill at a maximum of 2/3 of the top speed! Avoid abrupt braking or accelerating on gradients! If at all possible, avoid driving on slippery surfaces (such as snow, gravel, ice etc.) where...
Page 18
Danger of breaking down in adverse weather conditions, i.e. extreme cold, in an isolated area! If you are a user with severely limited mobility, we advise that in the case of adverse weather conditions DO NOT attempt a journey without an accompanying attendant! Danger of injury if your foot slides off the footrest and gets caught underneath the wheelchair when it is in motion! Make sure each time before you drive the wheelchair that your feet are squarely and securely...
Safety Information on Wheelchairs with a Lifter IMPORTANT - IF YOUR WHEELCHAIR IS EQUIPPED WITH A LIFTER: Danger of injury if the wheelchair tips over! Never exceed the maximum permissible load (see Technical Specifications)! Avoid dangerous driving situations when the lifter is in a raised position, such as trying to overcome obstacles like kerbs or driving up or down steep gradients! Never lean out of the seat when the lifter is raised! Inspect the lifter module at least once a month to make sure the automatic speed reduction...
Safety Information on Wheelchairs with Recaro Seats Danger of injury if the wheelchair tips over! The centre of gravity of a Recaro seat is higher than that of other seats. The Recaro seat is also heavier than other seating systems. The backrests of RECARO seats can be leaned back 90°.
Getting In and Out Getting in: Position the wheelchair as near to your seat as possible. If necessary, this can be done by an attendant. Switch your wheelchair off. Activate the hand brake (if your wheelchair has one). Remove the armrest our flip it upwards. Now slide over onto the wheelchair.
Driving Before driving for the first time... Before you take your first trip, you should familiarise yourself well with the operation of the vehicle and with all operating elements. Take your time to test all functions and driving modes. NOTE: If installed, use the restraining systems (seat belts) each time you use the vehicle.
Taking Obstacles Your wheelchair can overcome obstacles and kerbs with the following heights. STORM with front wheel type 200x50: STORM with front wheel type 3.00x4”: STORM with kerb climber: CAUTION: Danger of Tipping Over! Never approach obstacles at an angle! Put your backrest into an upright position before climbing an obstacle! Driving up over an obstacle Approach the kerb or obstacle slowly head-on.
Driving up and down gradients The STORM can safely climb gradients of up to 18%. When driving up or down gradients you should always observe the following precautions: WARNING: Danger of tipping over! Only ever drive downhill at a maximum of 2/3 of the top speed! Always return the backrest of your seat or the seat tilt to an upright position before ascending slopes! We recommend that you position the seat backrest or the seat tilt slightly to the rear before descending slopes!
Hand brake The 10 Km/h version of the STORM is equipped with an additional hand brake. The brake lever is normally mounted on the opposite side from the Joystick Box. Alternatively, the brake lever can be mounted on the same side as the Joystick Box with a special holder. To activate the brakes push the brake lever forward, to release pull the lever backwards.
Pushing the wheelchair by hand Disengaging Motors The motors of the wheelchair are equipped with automatic brakes, preventing that the wheelchair starts rolling out of control when the joystick box is switched off. When pushing the wheelchair, the magnetic brakes must be disengaged. Danger of the vehicle running away! When the motors are disengaged (for push operation), the electromagnetic motor brakes are deactivated! When the vehicle is parked, the levers for engaging and disengaging the motors...
The Advanced Control System (ACS) The main parts of the Joystick Box 1) Battery Charge Display 2) Driving and Adjustment Mode Display 3) Shift Up Driving Mode 4) Hazard Flasher Button 5) Left Flasher 6) Joystick 7) Status Display 8) Drive Away Interlock 9)Shift Down Driving Mode 10) ON/OFF 11) Light...
Page 29
The Pilot Lights on theJoystick Box: Left and Right Flashers (14+17) Hazard Flashers (15) Vehicle Lighting (16) On the bottom of the joystick box you will find: Socket for Programmer (18) the Charging Socket (19) Connection Socket for Supply Cable (20) Pilot lights...
Main components of the Joystick Box 7.2.1 Battery Charge Display The battery charge display (1) shows you the current charge status of the batteries. It is subdivided into 10 different-coloured LEDs: 2 x red, 4 x yellow and 4 x green. The decreasing battery charge, and thus the Powerchair's decreasing travelling range, is indicated by the individual diodes going out.
7.2.2 Status Display The ON/OFF LED (7) also functions as a Status Display or Error Display. Flashing of the display indicates a malfunction of the electrical equipment. The cause of the malfunction is indicated by a flash code. (Error codes see Chap. "Error Codes" on page 49.) The ACS Joystick Box monitors the following functions: Monitoring the electronics Monitoring the electrical components...
7.2.4 Symbols shown on the Multi-Purpose Display and their meanings = Driving Mode (select Driving Modes 1 - 5) = Adjustment of Electric Options* = Reduces driving speed when Lifter is raised or when the seat is not in an upright position These symbols only appear if your wheelchair is equipped with the corresponding electrical adjustment options.
7.2.5 Joystick With the Joystick (6) you can: Drive and steer Select and adjust electric actuators (like powered legrests). Driving speed and steering movement depend on the movement of the joystick. The regulation of speed and steering direction is continuous. Move Joystick to its furthest position in any direction = Maximum of selected top forward and cornering speed.
7.2.7 Charging Socket This socket (19) is also located on the bottom of the joystick box and serves to connect the battery charger. 7.2.8 Connection Socket for Supply Cable (Bus Cable) The connection cable serves the power supply of the joystick box and the data transfer from the joystick box to the main module.
Operating the Joystick Box 7.3.1 Switching the Joystick Box ON/OFF Switching ON: Press the ON/OFF Button (10) once. Displays: The Status Display in the Key-Symbol lights up. The battery charge display showing the current charge status. The Driving Mode Display showes the selected Driving Mode. Switching OFF: Press the ON/OFF Button (10) once again.
7.3.2 Drive Away Interlock The ACS is protected against unauthorised use by an electronic drive-away interlock. A sensor is located under the Key-Symbol. The Drive Away Interlock is activated and deactivated by touching the sensor area (8) with the magnetic key. Activating the drive-away lock: Switch the Joystick ON.
7.3.3 Lighting / Flashers Switching the lights on: Press the Lights Button (11) on the remote once. The Lighting- LED (16) on the display lights up. Switching the lights off: Press the Lights Button on the remote once again. The Lighting- LED (16) on the display goes out.
7.3.4 Horn Press the Horn Button (13). the horn sounds for as long as the button is pressed. 7.3.5 Hazard Flashers Activating the Hazard Warning Flasher: Press the Hazard Warning Flasher Button (4) once briefly. The Hazard Flasher is activated. The Hazard Flaher-LED (15) on the display lights up.
7.3.6 Selecting a Driving Mode "Driving Mode" means more than just "how fast". The Driving Mode encompasses: Acceleration Forward speed Backward speed Cornering speed The Multi-Purpose Display (2) indicates which mode the wheelchair is currently in. Different Driving Modes can be selected using the buttons (3 + 9) to the right and left of the display.
Page 40
Driving Mode is reached. The display (9) shows the selected Driving Mode. NOTE The electronics of the ACS has been programmed at the factory with default values. Individual programming, tailored to your specific requirements, can be performed by your authorised Invacare® Dealer. Switching Driving Modes...
7.3.7 Driving and Steering Driving forwards Move joystick forward. The movement of the joystick determines the driving speed. Driving backwards Move joystick backwards. The movement of the joystick determines the driving speed. Braking Move joystick back to centre position. NOTE In dangerous situations it is sufficient to release the joystick.
Page 42
Cornering Cornering Move the joystick in the desired direction whilst driving forward or backwards. The movement of the joystick determines the cornering speed. Turning on the spot Turning on the spot Move the joystick in the desired direction (left/right) WITHOUT forward or reverse speed.
Adjusting electric options using the Joystick Electric seat tilt, backrest angle, lifter and legrests can be adjusted using the Joystick (6). To be able to adjust the individual electric options, the Joystick Box must be switched from driving mode to adjustment mode. The Adjustment Symbols are displayed on the Multi-Purpose Display (2) of the Joystick Box.
7.4.1 Select Adjustment Mode Press the right or left buttons (3+9) repeatedly until the symbol shown at right appears on the display (L). Push Joystick (6) to the right or left (1+2) until the Adjustment Mode Symbol appears on the left display (L).
7.4.2 Symbols of the Adjustment Options The symbol depicted on the right display (R) shows which option be can adjusted. The individual options are designated by the following symbols: seat tilt backrest left angle legrest both right legrest Legrests lifter...
7.4.3 Select the option that needs to be adjusted Select: Push Joystick (6) once to the right or left. The flashing bar ( ) in the symbol on the right display (R) shows which option can be adjusted. By pushing the Joystick once again in the same direction, the next symbol can be selected.
7.4.4 Adjust option Raise option (H) by pushing the Joystick forward. Lower option (S) by pulling the Joystick backward. 7.4.5 Deselect Adjustment Mode Press the right or left buttons (3+9) repeatedly until the Driving Mode Symbol appears on the left display (L).
Troubleshooting on the ACS Control System Wheelchair slows down or doesn't move Check: Status display on joystick box extinguished? Status display on joystick box flashing? Red LED in battery charge display and status display flashing, driving mode display showing a horizontal bar. Check: Possible cause: Direct remedy:...
7.5.1 Error Codes The ACS electronics are capable to clear some faults automatically. In this case, the flashing of the status display will extinguish. To achieve this, switch the joystick box off and on again several times. Wait each time for about 5 seconds before switching the joystick box on again. If that does not eliminate the fault, identify the error by means of the flash codes listed below.
Page 50
Flash code: 5 x flashes 6 x flashes 7 x flashes 8 x flashes 9 or 10 x flashes 11 x flashes 12 x flashes Meaning: Direct remedy: Error/brake error in Check plug-and- right motor. socket Connection connections. loose/defective or motor defective.
Adjustment Options of the Joystick Box Below, some of the more important adjustment options of the Joystick Box are described. For a detailed description of the functions of the Joystick Box please see the Joystick Box User's Manual. 8.1.1 Adjusting the Joystick Box to length of the arm: Loosen the thumb screw that holds the Joystick Box by turning it counterclockwise.
8.1.3 Adjusting the height of the Joystick Box (option): Loosen the thumb screw that holds the Joystick Box by turning it counterclockwise. Adjust the height of the Joystick Box by sliding it upwards or downwards. Re-tighten the thumb screw that holds the Joystick Box by turning it clockwise.
Seating systems Standard and Kontur Seats 9.1.1 Adjusting the seat tilt Manual adjustment: Manual adjustment: Loosen the knurled nut (1) and screw downwards. Turn the threaded adjustment sleeve (2) counterclockwise = lift the front edge of the seat. Turn the threaded adjustment sleeve (2) clockwise = lower the front edge of the seat.
Page 54
Electric adjustment: The seat tilt of the wheelchair with electric actuator is adjusted using the ACS-Joystick Box. The adjustment is infinitely variable, and can be selected in the range between -1° and +18°. If your wheelchair is equipped with an electric lifter, then the adjustment range is between 0° and 9°. Switch the Joystick Box to Driving Mode "0”...
9.1.2 Backrest adjustment Manual adjustment: The lever for adjusting the backrest can be located either on the right or left side behind one of the clamping levers for adjusting the armrest height. Pull lever upwards. Press backrest backwards using your own weight. When the backrest is in the desired position, release the lever.
Page 56
Adjustment by metal plate with holes (available as an option for Standard Seats) The angle of the backrest is determined by the metal plate with screw- holes, which attaches the backrest to the frame. The angle can be changed by selecting different combinations of holes between 0°, 5°, 10°...
Page 57
Backrest with electric adjustment (option): WARNING: Danger of tipping over! When driving, the backrest angle must never exceed 15°! The backrest angle of the wheelchair with electric actuator is adjusted using the ACS-Joystick Box. The adjustment is infinitely variable, and can be selected in the range between 0° and 45°. Switch the Joystick Box to Driving Mode "0”...
9.1.3 Adjusting the headrest Height adjustment: Loosen the clamping lever (1). Slide the headrest to the desired height. Re-tighten clamping lever (1). Positioning the headrest: Loosen the clamping lever (2). Adjust the headrest to the desired angle. Re-tighten clamping lever (2).
9.1.4 Adjusting the height of the armrests Loosen the clamping lever. Pull the armrest upwards until the desired height is reached. Re-tighten clamping lever again. 9.1.5 Adjusting the height of the sideframes Loosen the screws using a 4 mm Allen Key. Adjust the sideframes to the desired position.
Loosen the clamping lever. Pull the armrest frames outwards until the desired width is reached. Re-tighten clamping lever again. 9.1.7 Adjusting the pommel: To position the pommel: Loosen the thumb screws (1 to 3) Adjust the pommel to the desired position. Re-tighten the thumb screws (1 to 3)
Recaro Seats 9.2.1 Recaro "N-Joy" and "Miles" (mechanically adjustable) Backrest adjustment: When the hand wheel is turned forwards, the backrest is raised. When the hand wheel is turned backwards, the backrest is lowered. Adjusting the height of the armrests Loosen one of the thumb screws depicted at right. Pull the armrest upwards until the desired height is reached.
9.2.2 Recaro Ergomed DS (electrically adjustable): For a detailed description of the functions of the Recaro Ergomed DS, please see the Recaro User's Manual. By pressing the buttons, the Recaro Seat can be individually adjusted. 1. Backrest cushion 1 2. Backrest cushion 2 3.
Invacare® Ultimate and Personal Special Seating Systems There are two different Invacare® Special Seating Systems, the Personal and the Ultimate versions. Both systems have ergonomically formed back and seat elements. In addition, the Ultimate back is equipped with inflatable side and lumbar cushions.
9.3.2 Seat version: Personal 9.3.2.1 Adjusting the height of the back Loosen the screws that hold both (1) retainer plates with a Phillips Screwdriver. Determine which holes in the backrest frame (2) and on the plates correspond to the desired height. Re-fasten the plates using the hole combination selected.
9.3.2.2 Adjusting the backrest angle The angle of the backrest is determined by the pins and the slots in the plates on the backrest frame. Release the securing belts (1) for the lower backrest holder (Velcro). Plate - pins lower slot Lower backrest holder...
Page 66
Turn the levers (1) of both holders until the cams (2) can be pulled out of the slots on the plates. Unhook the upper backrest support and reposition it in the desired slots. Bring the lower backrest support into the desired position. Turn the levers (1) of both holders until the cams (2) can be slid into the slots on the plates.
9.3.3 Seat version: Ultimate 9.3.3.1 Adjusting the height of the back Loosen the retainer screws (1) of both upper backrest holders with a 4mm Allen Key. Adjust to the desired height. Tighten the screws again. Position of the backrest holder Backrest holder...
9.3.3.2 Adjusting the backrest angle The angle of the backrest is determined by the metal plate with screw-holes, which attaches the backrest to the frame. The angle can be changed by selecting different combinations of holes between 0°, 5°, 10° or 15° (see drawing). Remove the screws that hold the backrest frame on both sides using a 13 mm open-end spanner.
Fine adjustment of the backrest angle: By turning the hand wheel, the backrest angle can be finely adjusted. Turn the hand wheel to the right Turn the hand wheel to the left 9.3.3.3 Adjusting the inflatable cushions Inflate the inflatable cushions to the required size using the rubber hand pumps.
9.3.3.4 Removing the backrest Loosen the clamps on both upper backrest holders by turning them. Upper backrest holders Lower latching mechanism...
Page 71
Pull both lower latching mechanisms and remove backrest in an upward direction. Refitting the backrest: Fit the backrest into the upper backrest holders and tighten the clamps. Pull the lower release mechanisms and snap the backrest into the backrest frame. Pull the levers Refitting the backrest...
This way the footrest can be individually adjusted to the angle of the seat the user's needs. Adjustment of the footrest can be done with corresponding tools. We recommend that this adjustment be done by a trained Invacare® Dealer.
10.1.1.2 Footrest: Adjusting the Angle Warning: Danger of Injury if footrest or legrest is incorrectly adjusted! Before and during each drive, always make sure there is sufficient clearance between the legrest (or footrest) and the ground, as well as the castors! Loosen the screw that allows the angle to be adjusted (1).
10.1.1.3 Footrest: Adjusting the Length Loosen the screw which allows the length to be adjusted using a 5mm Allen Key. Adjust to the desired length. Tighten the screw again. 10.1.1.4 Footrest: Adjusting the Angle of the Footplate (Option) Loosen both screws of the footplate using a 5mm Allen Key. Adjust to the desired angle.
10.2 Legrests 10.2.1 Settable Legrest (Option) Manual Height Adjustment Angle Adjustment of the Legrest = 90° - 0° Footplate Angle Adjustable General Information The settable legrest can easily be adapted to the individual needs of the user. The angle of the footrest in relation to the seat and its length are adjustable. This way the footrest can be individually adjusted to the angle of the seat the user's needs.
10.2.1.2 Settable legrest: Adjusting the Angle Warning: Danger of Injury if footrest or legrest is incorrectly adjusted! Before and during each drive, always make sure there is sufficient clearance between the legrest (or footrest) and the ground, as well as the castors! Release the quick-release (1) of the angle adjustment by pulling the lever Adjust to the desired angle (2).
10.2.1.3 Settable legrest: Adjusting the Length Loosen the screw that allows the length to be adjusted. Adjust to the desired length. Tighten the screw again. 10.2.1.4 Settable legrest: Adjusting the Angle of the Footplate Loosen both screws of the footplate using a 5mm Allen Key. Adjust to the desired angle.
The manually height-adjustable legrest provides quick mechanical adjustment of the angle of the legrest. Adjustment of the length of the legrest and of the angle of the footplate can be done with corresponding tools. We recommend that this adjustment be done by a trained Invacare® Dealer.
10.2.2.2 Height Adjustment for Ergonomic Length Compensation Warning: Danger of Injury if footrest or legrest is incorrectly adjusted! Before and during each drive, always make sure there is sufficient clearance between the legrest (or footrest) and the ground, as well as the castors! Ergonomic Length Compensation of the legrest is only given if the pivot point of the legrest (1) corresponds with that of the user's knee.
10.2.2.3 Manually adjustable legrest: Angle Adjustment Warning: Danger of injury by moving parts! Do not place fingers in the area between the upper and lower parts of the legrest! Adjust the legrest upward by pulling it up to the desired angle (1). To lower the legrest, hold it by the footplate, pull the adjustment lever on the side (2) and slowly lower the legrest (3).
10.2.2.4 Manually adjustable legrest: Adjusting the Length Loosen the screw which allows the length to be adjusted using a 5mm Allen Key. Adjust to the desired length. Tighten the screw again. 10.2.2.5 Manually adjustable legrest: Adjusting the Angle of the Footplate Loosen both screws of the footplate using a 5mm Allen Key.
The angle of the electrically elevatable legrest can the adjusted electrically. Adjustment of the length of the legrest and of the angle of the footplate can be done with corresponding tools. We recommend that this adjustment be done by a trained Invacare® Dealer.
10.2.3.2 Height Adjustment for Ergonomic Length Compensation Warning: Danger of Injury if footrest or legrest is incorrectly adjusted! Before and during each drive, always make sure there is sufficient clearance between the legrest (or footrest) and the ground, as well as the castors! Ergonomic Length Compensation of the legrest is only given if the pivot point of the legrest (1) corresponds with that of the user's knee.
10.2.3.3 Electrically adjustable legrest: Angle Adjustment Warning: Danger of injury by moving parts! Do not place fingers in the area between the upper and lower parts of the legrest! The electric actuator, which adjusts the angle, is controlled using the remote.
10.2.3.4 Legrest: Adjusting the Length Loosen the screw which allows the length to be adjusted using a 10 mm open-end spanner. Adjust to the desired length. Tighten the screw again. 10.2.3.5 Legrest: Adjusting the Angle of the Footplate Loosen both screws of the footplate using a 5mm Allen Key. Adjust to the desired angle.
10.3 Width Adjustment of the Legrests (Option): The screws that allow adjustment of the width are located under the seat. NOTE: The lights must not be obscured by the legrests. If necessary, they must be positioned farther toward the outside. To do this, use the different holes of the mounting plates.
Lifter (option) The seat-lifting system for the STORM, called the STORM Lifter, is a useful option that provides the active user with more flexibility by lifting the seat up to 30 cm. It is available in two versions: the one allows a permanent adjustment of the seat tilt by means of adjustment screws, the other is equipped with an electric actuator for this purpose.
11.1 Adjusting the seat tilt on a STORM with a Lifter Module Manual adjustment of the seat tilt of the Standard Seat or the Kontur Seat: During adjustment no one may be seated in the chair. Remove the screws that allow adjustment of the seat tilt, which are in the front under the seat.
11.2 Adjustment of the electric Lifter Module: The electric actuator which adjusts the height is controlled using the remote. Select Menu Point "0” using the "Driving Mode Shift Down” Button on the remote. The symbol changes automatically from "0” to a symbol of the seat.
11.3 Automatic speed reduction: The STORM Lifter has a safety function, which automatically reduces the speed of the wheelchair as soon as the lifter is raised. In this mode the Status Display on the Joystick Box flashes two times repeatedly. The speed of the STORM is reduced as follows: Lifter down = 100% of wheelchair's maximum power.
Electrical System 12.1 Electronics Protection System The vehicle's electronics are equipped with an overload-protection system. If the motors are put under considerable strain for a longer period of time (for example, when driving up a steep hill) and especially when the ambient temperature is high, then the electronic system could overheat.
12.2 Batteries 12.2.1 What you need to know about batteries Power is supplied by two 12V gel batteries. The batteries are maintenance-free and only need regular charging. New batteries should always be fully charged once before their first use. New batteries will be at their full capacity after having run through approx.
Page 97
The batteries cannot be overcharged with the specified charger. Please use only charging devices in Class 2. This class of chargers may be left unattended during charging. All charging devices which are supplied by Invacare® and comply with these requirements.
Danger of explosion and destruction of batteries if the wrong battery charger is used! Only ever use the battery charger supplied with your vehicle, or a charger that has been approved by Invacare®! Danger of electric shock and damage to the battery charger if it is allowed to get wet!
Page 99
Charging the batteries Switch off the wheelchair at the Joystick Box. Connect the battery charger to the Joystick Box - the charging socket is located on the bottom of the Joystick Box. Connect battery charger to the mains outlet and switch on if necessary.
12.2.3 Removing and fitting batteries WARNING: Danger of injury if the batteries are not handled correctly during assembly and maintenance work! New batteries should be installed by authorised technicians! Observe the warnings on the batteries! Take into account the heavy weight of the batteries! Only ever use the battery type defined in the technical specifications! Danger of fire and burns if battery terminals are short-circuited! DO NOT short-circuit battery terminals with a tool!
12.2.3.1 Removing and refitting the 70 Ah batteries Requirements: Spanner; 11 mm Flip the battery cradle flap / lighting panel upwards. Remove the battery cover by pulling it backwards and upwards (it is held by two Velcro strips).
Page 102
Remove the belt that holds the batteries. Loosen the battery-cable terminal of the blue cable (minus pole) on the first battery using the spanner (11 mm) and remove cable. Remove the insulator cap of the red cable (plus pole) from the battery;...
Page 103
Loosen the battery-cable terminal of the blue cable (minus pole) on the second battery using the spanner (11 mm) and remove cable. Remove the insulator cap of the red cable (plus pole) from the battery; loosen battery-cable terminal and remove. Remove second battery by pulling it backwards out of the wheelchair.
12.2.3.2 Removing and fitting the 55 Ah batteries (old STORM model) Flip the battery cradle flap / lighting panel upwards. Pull first battery backwards and remove. Pull second battery backwards and remove also. NOTE To refit the batteries, proceed in reverse order.
Only ever transport damaged batteries in an appropriate acid-resistant receptacle. Wash all objects that have come into contact with acid with lots of water. Disposing of dead or damaged batteries correctly Dead or damaged batteries can be given back to your dealer or directly to Invacare®.
12.3 Lighting The lighting system on the STORM is controlled using the Joystick Box. Please see the chapter on the Joystick Box. NOTE To reduce the risk of the headlamps and flashers being damaged, they are mounted on flexible rubber fittings. For this reason they may get turned slightly off centre during normal use of the wheelchair.
The following are instructions on repairs that can be performed by the user. For the specifications of spare parts please see "Technical Specifications" on page 121, or consult the Service Manual, available from Invacare®. In case you require assistance, please contact your Invacare® Dealer. 13.1...
Page 108
Tail lights and rear flashers Remove the screws (1) that hold the tail light and flasher bar in place. Remove the cover. Replace the light bulb with a new one. Refit the cover. Reposition the screws and tighten.
13.2 Repairing a flat tyre 13.2.1 Repairing a flat tyre (pneumatic tyres type 200 x 50) Requirements: Allen key 5 mm 2 x Open-end spanners 13 mm Repair kit for inner tubes or an new inner tube. Talcum powder Remove the wheel Jack the vehicle up and place a block of wood underneath it to prop it up.
Page 110
Repair the flat tyre. Remove the valve cap. Let the air out of the tyre by pressing the pin in the centre of the valve in. Remove the 5 Allen screws (3) Take the tyre and the inner tube off of the rim halves.
13.2.2 Repairing a flat tyre (pneumatic tyres type 3.00x4") Requirements: Allen key 5 mm Open-end spanner 17 mm Repair kit for inner tubes or an new inner tube. Talcum powder Remove the front wheel Jack the vehicle up and place a block of wood underneath it to prop it up.
Page 112
Remove the valve cap. Let the air out of the tyre by pressing the pin in the centre of the valve in. Remove the 5 Allen screws (3) Take the tyre and the inner tube off of the rim halves. Repair the inner tube and re-fit, or replace it with a new one.
13.2.3 Repairing a flat tyre (pneumatic tyres type 3.00-8") Requirements: Allen key 5 mm Repair kit for inner tubes or an new inner tube. Talcum powder Remove the wheel Jack the vehicle up and place a block of wood underneath it to prop it up. Remove the 4 countersunk screws (1).
Page 114
Repair the flat tyre. Remove the valve cap. Let the air out of the tyre by pressing the pin in the centre of the valve in. Remove the 5 cylinder head screws (back of the wheel, 2). Remove the rim halves from the tyre. Remove the inner tube from the tyre.
Care and maintenance NOTE: Have your wheelchair checked at least once a year by an authorised Invacare® Dealer, to ensure that vehicle safety and roadworthiness of the wheelchair are maintained. Cleaning the wheelchair When cleaning the wheelchair, please observe the following points: Only ever clean the Joystick Box, seat upholstery and armrests with a damp cloth and a gentle cleaning agent.
Page 116
Maintenance Jobs Seat and backrest padding: - Check for perfect condition. Side part and armrest: - Are all fastening elements installed? - Can armrests / side parts be removed and installed without too much physical effort? - Are armrests secured in their positions? Legrests: - Do legrests lock into place without any problem? - Do the different adjustment functions work without any problem?
Page 117
If the wheelchair is serviced at regular intervals, damaged or worn parts can be located and replaced in time, thus preserving it in good working order. A complete checklist of necessary maintenance work can be found in the Service Manual, which can be obtained from Invacare®. Before every trip Before each trip...
Transport 15.1 Transferring the wheelchair to another vehicle WARNING: Danger of tipping over, if the wheelchair is transferred to another vehicle with the user seated in it! If the wheelchair has to be transferred to another vehicle over a ramp, then it must be secured against tipping over by an attendant standing behind it during the transfer process! Drive or push your wheelchair into the transport vehicle using a suitable ramp.
15.2.1 The Taxi Bar The illustration at right shows the optional Taxi Bar for Holland. The Taxi Bar can be used to secure the STORM by means of the latching mechanism used in Holland, or also to secure the STORM using belts. 15.2.2 Anchor ring, lateral (Option): The illustration at right shows the optional securing bar.
15.2.3 "Crash Kit" (Option): For the highest level of security when transporting the STORM in another vehicle, we recommend the optional "Crash Kit", which was developed specially for this purpose. The "Crash Kit" comprises the following: a traverse bar, which is bolted to the frame, and which provides the front securing points (traverse bar of the kerb climber)...
Technical Specifications Wheelchair Classification Dimensions Armrest Height Armrest Depth Footrest Length (adjustable range of the standard footrest) Total Width Total Height (without headrest) Total Height (with headrest) Total Height (wheelchair folded together) Total Length Type B (for indoor and outdoor use) approx.
Page 122
Seat Width Seat Height Seat Depth Seat tilt adjustment Seat Adjustment Standard/Kontur Recaro Arne Jensen Invacare® Ultimate Special Seating System Invacare® Personal Special Seating System Standard/ Kontur (with seat cushion) Recaro (front edge of seat) Arne Jensen (4° tilt) (front edge...
Page 123
Electrical System Batteries Electrical System Electronics Light bulbs (6 Headlights km/h) Flasher, front Tail light Flasher, rear Light bulbs (10 Headlights km/h) Flasher, front Tail light Flasher, rear Battery Charger Fuse Main Battery Fuse Recaro Seat fuse Standard: 2 x 12 V 70Ah, maintenance-free, sealed, gel Optional: 2 x 12 V 55Ah, maintenance-free, sealed, gel...
Page 124
3.00x8” all wheels 250 kPa (corresponds to 2.5 bar) Standard approx. 114 kg Kontur approx. 116 kg Invacare® Special approx. 118 kg Seating Systems Recaro approx. 116 kg Arne Jensen approx. 116 kg without lifter 100 or 150 kg (see data plate)
Page 125
Driving attributes Range according to 70 Ah / 6 km/h ISO 7176, approx. version 70 Ah / 10 km/h version Note: The wheelchair's range depends strongly on various factors, such as battery charge, ambient temperature, local topography, road conditions, tyre pressure, driver's weight, driving habits and the usage the batteries for lighting, actuators, and so on. Under optimum conditions the 6 km/h version of the STORM has attained up to 50 km.
It is confirmed by stamp and signature that all jobs listed in the inspection schedule of the Service and Repair Instructions have been properly performed. The list of the inspection jobs to be performed can be found in the Service Manual which is available through Invacare®. Delivery Inspection...