Invacare Storm User Manual
  1. Manuals
  2. Brands
  3. Invacare Manuals
  4. Wheelchair
  5. STORM
  6. User manual
Invacare Storm User Manual

Invacare Storm User Manual

Hide thumbs Also See for Storm:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual
Yes, you can.
®
Invacare® Storm³
Power Wheelchair
User Manual

Advertisement

Table of Contents
loading

Related Manuals for Invacare Storm

Summary of Contents for Invacare Storm

  • Page 1 Yes, you can. ® Invacare® Storm³ Power Wheelchair User Manual...
  • Page 3 How can you get in touch with Invacare®? If you have any questions or need support, please contact your authorised Invacare® Dealer, who has the necessary know-how and equipment plus the special knowledge concerning your Invacare® product, and can offer you all-round satisfactory service. Should you wish to contact Invacare® directly, you can reach us in Europe at the following addresses and phone numbers.
  • Page 4 +44 (0)1656 77 62 20 Pencoed uk@invacare.com Bridgend CF35 5AQ WWW: www.invacare.co.uk United Kingdom Invacare Mecc San s.r.l. +39 0445 38 00 59 Via dei Pini, 62 Fax: +39 0445 38 00 34 I - 36016 Thiene (VI) italia@invacare.com ITALIA WWW: www.invacare.it...
  • Page 5 +46 (0)8 761 81 08 Fagerstagatan 9 sweden@invacare.com S-163 91 Spånga finland@invacare.com Sverige WWW: www.invacare.se Tillverkare: MÖLNDAL Invacare® Deutschland GmbH  : +46 (0)31 86 36 00 Kleiststraße 49 Fax: +46 (0)31 86 36 06 D-32457 Porta Westfalica ginvacare@invacare.com Deutschland LANDSKRONA ...

  • Page 6: Table Of Contents

    Table of Contents Chapter Page Introduction Important symbols in this manual ..................12 Important symbols found on the vehicle ................14 1.2.1 Explanation of symbols on lifter warning sticker............16 Type classification and permissible use................17 Indications..........................17 Usability............................18 Warranty ...........................19 Life expectancy........................19 Safety notes General safety notes .......................20 Safety information with regard to care and maintenance ...........23 Safety information on electromagnetic interference ............24...
  • Page 7 Driving up and down gradients....................39 Parking and stationary......................39 Use on public roads ........................40 Pushing the wheelchair in freewheel mode Disengaging the motors (Storm³ with conventional motors) ..........41 Disengaging the motors (Storm³ with GB motors) ..............43 Remotes Adjusting the wheelchair to the user's seating posture Adjusting the armrests and the control panel..............46...
  • Page 8 The Lifter ..........................60 8.6.1 Explanation of symbols on lifter warning sticker............62 Adjusting the lateral supports (Flex Seat) ................63 8.7.1 Adjusting the width......................63 8.7.2 Adjusting the height ......................64 8.7.3 Adjusting the depth .......................65 Adjusting the headrest (Flex Seat) ..................66 Legrests............................67 8.9.1 Standard 80°...
  • Page 9 8.9.4.5 Adjusting the height of the calf pad .................96 8.9.4.6 Unlocking and swivelling the calf plate backward when alighting ......97 8.9.4.7 Adjusting the angle adjustable foot plate..............98 8.9.4.8 Adjusting the angle and depth adjustable foot plate ..........99 8.9.5 Electrically height adjustable legrest 80° - 0° with ergonomic length adjustment ..100 8.9.5.1 Swivelling the legrest outward and/or removing............100 8.9.5.2...
  • Page 10 9.2.5.1 General instructions on handling the batteries ............118 9.2.5.2 How to handle damaged batteries correctly ............118 9.2.5.3 Removing the batteries..................120 10 Care and maintenance 10.1 Cleaning the mobility device ....................122 10.2 Inspection checks .........................123 11 Repair instructions 11.1 Repairing a flat tyre .......................126 11.1.1 Repairing a flat tyre (front) ..................127 11.1.2 Repairing punctures (drive wheel with GB motor and pneumatic tyres) ....130 11.1.3 Repairing punctures (drive wheel with conventional motor and pneumatic tyres) ..133...

  • Page 11: Introduction

    The decision whether the model is suitable for the user may only be taken by medical specialists with appropriate expertise. Invacare® or their statutory representatives can accept no liability in cases in which the wheelchair has not been adapted to suit the users’ handicaps.

  • Page 12: Important Symbols In This Manual

    This manual contains copyrighted information. This manual may not be reproduced or reprinted either partly or completely without previous written consent from Invacare® or its statutory representatives. We reserve the right to make any necessary alterations on the grounds of technical improvements.
  • Page 13 RISK OF CRUSHING! This symbol warns of a risk of crushing caused by being careless with heavy components. • Always follow the instructions to avoid injury to the user or damage to the product. Wear eye protection This symbol refers to the requirement for wearing eye protection, for example when working with batteries.

  • Page 14: Important Symbols Found On The Vehicle

    Important symbols found on the vehicle This product has been supplied from an environmentally aware manufacturer. This product may contain substances that could be harmful to the environment if disposed of in places (landfills) that are not appropriate according to legislation. •...
  • Page 15 • Please always make sure that the wheelchair is equipped with a headrest approved by Invacare before using it as a vehicle seat! This symbol indicates the maximum width to which an armrest may be adjusted. Pulling the armrest out further can cause it to fall out of it's fixation.

  • Page 16: Explanation Of Symbols On Lifter Warning Sticker

    If the power wheelchair is fitted with a table, it is imperative that it is removed and safely stowed when transporting the wheelchair in a vehicle! 1.2.1 Explanation of symbols on lifter warning sticker Do not lean out Do not drive up Do not allow any Never drive with Never drive over...

  • Page 17: Type Classification And Permissible Use

    Type classification and permissible use This vehicle was designed for persons whose ability to walk is impaired, but who are still in terms of their eyesight and physically and mentally able to operate an electric vehicle. It has been classified according to EN 12184 as a class B mobility product (for indoor and outdoor areas).

  • Page 18: Usability

    You should immediately stop using your power wheelchair if its usability is restricted due to: - brake failure • You should immediately contact an authorised Invacare® dealer if the usability of your power wheelchair is restricted due to: - the lighting system failing or being defective...

  • Page 19: Warranty

    - unusual sounds developing or occurring Or if you have the feeling that something is wrong with your wheelchair. Warranty The terms and conditions of the warranty are part of the general terms and conditions particular to the individual countries in which this product is sold. Life expectancy We estimate a life expectancy of five years for this product, provided it is used in strict accordance with the intended use as set out in this document and all maintenance and service requirements...

  • Page 20: Safety Notes

    Safety notes READ WELL BEFORE OPERATION! General safety notes Danger of injury if mobility device is used in any other way than the purpose described in this manual! • Only ever use the mobility device in accordance with the instructions in this User's Manual (see chapter "Type classification and permissible use"...
  • Page 21 Danger of injury if the mobility device is switched off while driving, for example by pressing the On/Off Button or disconnecting a cable, due to it coming to an abrupt, sharp stop! • If you have to brake in an emergency, simply release the joystick which will bring you to a halt. (refer to the joystick operating manual for more information).
  • Page 22 Danger of fire or breaking down due to electric devices being connected! • Do not connect any electric devices to your mobility device that are not expressly certified by Invacare® for this purpose. Have all electrical installations done by your authorised Invacare® Dealer.

  • Page 23: Safety Information With Regard To Care And Maintenance

    Safety information with regard to care and maintenance Danger of accident and loss of guarantee if maintenance is insufficient! • For reasons of safety and in order to avoid accidents which result from unnoticed wear, it is important that this electric mobility product undergoes an inspection once every year under normal operating conditions (see inspection plan contained in service instructions).

  • Page 24: Safety Information On Electromagnetic Interference

    Safety information on electromagnetic interference This electric vehicle was successfully tested in accordance with International standards as to its compliance with Electromagnetic Interference (EMI) regulations. However, electromagnetic fields, such as those generated by radio and television transmitters, and cellular phones can influence the functions of electric vehicles.

  • Page 25: Safety Information On Driving And Freewheel Mode

    Safety information on driving and freewheel mode Danger of injury if the wheelchair tips over! • Inclines and declines can only be travelled up to the maximum safe slope (see chapter "Technical specifications" from page 149). • Always return the backrest of your seat or the seat tilt to an upright position before ascending slopes.
  • Page 26 Danger of breaking down in adverse weather conditions, i.e. extreme cold, in an isolated area! • If you are a user with severely limited mobility, we advise that in the case of adverse weather conditions DO NOT attempt a journey without an accompanying attendant! Danger of injury if your foot slides off the footrest and gets caught underneath the wheelchair when it is in motion! •...

  • Page 27: Safety Information Regarding Changes And Modifications To The Mobility Device

    EEC / MPG (Medical Devices Act) and only applies to the complete product. The CE marking is invalidated if components or accessories are replaced or added that have not been approved for this product by Invacare. In this case, the company that adds or replaces the components or accessories is responsible for the conformity assessment/ CE marking or for registering the wheelchair as a special design and for the relevant documentation.
  • Page 28 • Only use seating systems that have been approved by Invacare® for this power wheelchair. Electrical and electronic components which have not been approved by Invacare® for use with this mobility aid can cause fire hazards and lead to electromagnetic damage! •...

  • Page 29: Safety Information On Wheelchairs With A Lifter

    Safety information on wheelchairs with a lifter WARNING! Danger of injury by moving parts! • Never let objects get caught in the space underneath a raised lifter! • Make sure that neither you nor anyone else is injured by placing hands, feet other body extremities under the raised seat! •...

  • Page 30: Safety Information On Wheelchairs With Recaro Seats

    Safety Information on Wheelchairs with Recaro Seats Danger of injury if the wheelchair tips over! The centre of gravity of a Recaro seat is higher than that of other seats. The Recaro seat is also heavier than other seating systems. The backrests of RECARO seats can be leaned back 90°.

  • Page 31: Key Features

    Key features 1) Push handle 2) Armrest 3) Remote 4) Battery case (rear) 5) Headrest 6) Backrest 7) Footrests 8) Drive motor (with disengaging lever)

  • Page 32: Getting In And Out Of The Wheelchair

    Getting in and out of the wheelchair Danger of injury if legrests break due to use as a stepping board! • Do not use the legrests as a stepping board when getting in and out of the wheelchair! Important information when side transferring in and out of the wheelchair In order to side transfer it is necessary for the armrest to either be raised or removed completely depending on the model.

  • Page 33: Raise The Parallel Sliding Armrest / Remove The Skirtguard (Optional)

    Removing the armrest: • Loosen the fastening screw (1). • Pull the side section out of the receptacle. Raise the parallel sliding armrest / remove the skirtguard (optional) Raising the armrest • Raise the armrest in order to side transfer.
  • Page 34 Remove the skirtguard (option) in order to side transfer: • Release the clamping lever (1). • Pull the skirtguard out of the receptacle.
  • Page 35 Getting into the wheelchair: • Position your wheelchair as close as possible to your seat. This might have to be done by an attendant. • Switch your wheelchair off. • Apply the manual wheel lock of your wheelchair (if existing). •...

  • Page 36: Driving

    Driving Before driving for the first time... NOTE The maximum load capacity that is stated in the technical data only states that the system is designed for this mass in total. However, this does not mean that one can sit a person with this body weight in the wheelchair without restrictions.

  • Page 37: Taking Obstacles

    • The rear mirror (if installed) is adjusted so you can look behind at all times without having to bend forward or shift your seating position. Taking Obstacles 5.2.1 Maximum obstacle height You can find information about maximum obstacle heights in the chapter entitled "Technical specifications"...

  • Page 38: The Correct Way To Overcome Obstacles

    5.2.3 The correct way to overcome obstacles Ascending Right • Approach the obstacle or the kerb slowly, head-on and at a right angle. • Depending on the wheel drive type, stop in one of the following positions: - In the case of centrally driven wheelchairs: 5 - 10 cm before the obstacle. - For all other drives: approx.

  • Page 39: Driving Up And Down Gradients

    Driving up and down gradients For information concerning the maximum safe slope, please see chapter "Technical specifications" starting on page 149. WARNING: Danger of tipping over! • Only ever drive downhill at a maximum of 2/3 of the top speed. Avoid sudden changes of direction or abrupt braking when driving on slopes.

  • Page 40: Use On Public Roads

    If you wish to use your wheelchair on public roads and lighting is required by national legislation, then your wheelchair needs to be equipped with an appropriate lighting system. Please contact your Invacare ® dealer if you have any questions.

  • Page 41: Pushing The Wheelchair In Freewheel Mode

    When pushing the wheelchair manually whilst freewheeling, the magnetic brakes must be disengaged. Disengaging the motors (Storm³ with conventional motors) Danger of the vehicle running away! • When the motors are disengaged (for push operation whilst freewheeling), the electromagnetic motor brakes are deactivated! When the vehicle is parked, the levers for engaging and disengaging the motors must without fail be locked firmly into the "DRIVE"...
  • Page 42 NOTE: The motors may only be disengaged by an attendant, not by the user! This ensures that the motors are only disengaged if an attendant is available to secure the wheelchair and prevent unintended rolling. Disengaging the motors: The lever for engaging and disengaging the motors is located on the right motor.

  • Page 43: Disengaging The Motors (Storm³ With Gb Motors)

    Disengaging the motors (Storm³ with GB motors) Danger of the vehicle running away! • When the motors are disengaged (for push operation whilst freewheeling), the electromagnetic motor brakes are deactivated! When the vehicle is parked, the levers for engaging and disengaging the motors must without fail be locked firmly into the "DRIVE"...

  • Page 44: Remotes

    Re-engaging motors • Pull the lever (1) to the rear. The motors are now re-engaged. Remotes Your wheelchair may be equipped with one of several different remotes. For information on the different functions and how to operate a particular remote, please see its corresponding User Manual (enclosed).

  • Page 45: Adjusting The Wheelchair To The User's Seating Posture

    Adjusting the wheelchair to the user's seating posture CAUTION: Damage to wheelchair and accident hazard! It is possible that collisions can occur between wheelchair components due to various combinations of adjustment options and their individual settings! • The wheelchair is fitted with an individual, multiply adjustable seating system including adjustable legrests, armrests, a headrest or other options.

  • Page 46: Adjusting The Armrests And The Control Panel

    Adjusting the armrests and the control panel The following information is valid for all seating systems. 8.1.1 Adjust the control panel for the length of the user's arm (all seat systems) The remote can be adjusted to the length of the user's arm, and - depending on the type - it is either affixed with an Allen screw or a wing screw.
  • Page 47 • Loosen the wing screw (1). • Set the remote to the desired length by adjusting forward or backward. • Re-tighten the screw.

  • Page 48: Adjusting The Height Of The Joystick Box (Only With Swing-Away Joystick)

    8.1.2 Adjusting the height of the joystick box (only with swing-away joystick) • Loosen one or both of the wing screws (1 and 2) that allow height adjustment of the joystick box. • Adjust the joystick box to the desired height. •...

  • Page 49: Adjusting The Height Of The Armrests (All Seats)

    8.1.3 Adjusting the height of the armrests (all seats) The height of the armrest can be adjusted, and -depending on the type - is either affixed by an Allen screw or a wing screw. Requirements: • Allen key 3 mm •...
  • Page 50 • Loosen the wing screw (1). • Set the armrest to the desired height. • Re-tighten wing screw.

  • Page 51: Setting The Height Of The Parallel Sliding Armrests

    8.1.4 Setting the height of the parallel sliding armrests Requirements: • Allen key 2 mm • Loosen the screws (1) on both sides of the handle, using the Allen key 2 mm. • Turn the spindle in a clockwise direction (A). The armrest will be raised.

  • Page 52: Adjusting The Angle Of The Armpad On The Parallel Sliding Armrests

    8.1.5 Adjusting the angle of the armpad on the parallel sliding armrests Requirements: • Allen key 4 mm • Open-end spanner 10 mm • Loosen the screw (1, on the inner side of the armrest), which allows adjustment of the angle of the armpad, while countering the nut (2, outer side of the armrest) with the open-end spanner, if...

  • Page 53: Adjusting The Width Of The Armrests

    8.1.6 Adjusting the width of the armrests The space between the side sections can be adjusted 2 cm on both sides (4 cm total). Requirements: • Allen key 8 mm Where to find the adjustment screws The picture below shows the position of the screws that allow adjustment of the width of the armrests.
  • Page 54 Doing the adjustment • Loosen screw (1). • Adjust armrest to desired position. • Re-tighten screw. • Repeat procedure for the other armrest.

  • Page 55: Manually Adjusting The Seat Tilt

    Manually adjusting the seat tilt The manual seat angle adjustment has a range which can be set from between 0° and 25°. The seat angle is adjusted using a spindle which is located at the front, underneath the seat frame. When adjusting the seat angle, you should ensure that the threaded rod is not completely unscrewed from out of the spindle, and that at least one centimetre remains screwed inside.

  • Page 56: Adjusting The Seat Height Manually

    Adjusting the seat height manually The manual seat adjustment has an adjustable range of 10 cm. The seat height is adjusted using a spindle which is located in the middle, underneath the seat frame. When adjusting the seat height, you should ensure that the threaded rod is not completely unscrewed from out of the spindle, and that at least one centimetre remains screwed inside.

  • Page 57: Manually Adjusting The Backrest

    Manually adjusting the backrest 8.4.1 Flex and Contour seats • Adjust the angle by turning the knob (1).

  • Page 58: Standard Seat

    8.4.2 Standard Seat The angle of the backrest has six positions, from -10° to +30°. • Remove the screws (1) on both sides of the backrest that hold it in position. • Set the backrest to the desired angle by selecting a combination of one of the two holes in the backrest frame, and one of the six holes in the metal fixation plate.

  • Page 59: Postural Belts

    Postural belts A postural belt is an option which can either be fixed to the wheelchair ex-works or can be retrofitted by your specialist dealer. If your wheelchair is fitted with a postural belt, your specialist dealer will have informed you about fitting and usage. The postural belt is used to help the wheelchair user keep an optimum sitting position.

  • Page 60: Adjusting The Postural Belt Correctly

    You can find more information about maintenance work on belts in the service manual, which is available from Invacare®. The Lifter The electric lifter is operated from the remote. Please refer to the remote manual for more...
  • Page 61 Information regarding operation of the lifter at temperatures of less than 0 °C Invacare® mobility aids are fitted with safety mechanisms that prevent capacity overload of the electronic components. At operating temperatures below freezing point this can, in particular, lead to the lifter actuator being shut down after approx. 1 second operating time.

  • Page 62: Explanation Of Symbols On Lifter Warning Sticker

    8.6.1 Explanation of symbols on lifter warning sticker Do not lean out Do not drive up Do not allow any Never drive with Never drive over when the lifter is or down slopes body parts to get two people! uneven surfaces raised! when the lifter is under a raised...

  • Page 63: Adjusting The Lateral Supports (Flex Seat)

    Adjusting the lateral supports (Flex Seat) The trunk supports can be adjusted in three different ways: • Width • Height • Depth 8.7.1 Adjusting the width • Loosen the knobs (1) that hold the lateral supports. • Adjust the supports to the desired width. •...

  • Page 64: Adjusting The Height

    8.7.2 Adjusting the height Requirements: • Allen key 5 mm • Loosen the screws (1) that allow height adjustment of the lateral supports. • Adjust the supports to the desired height. • Re-tighten the screws.

  • Page 65: Adjusting The Depth

    8.7.3 Adjusting the depth Requirements: • Allen key 5 mm • Loosen the screws (1) that allows the support pads to slide forwards and backwards. • Adjust the supports to the desired position. • Re-tighten the screws.

  • Page 66: Adjusting The Headrest (Flex Seat)

    Adjusting the headrest (Flex Seat) • Loosen the clamping lever (1, 2 or 3). • Adjust the headrest to the required position. • Retighten clamping lever.

  • Page 67: Legrests

    Legrests 8.9.1 Standard 80° footrests 8.9.1.1 Swinging the footrests outwards and/or removing them The small release lever is to be found in the upper part of the legrest (1). When the legrest is released it can be swivelled inward or outward to facilitate access and also be removed completely.
  • Page 68 • Push the release lever inward or outward. The legrest is released. • Swivel the legrest inward or outward. • To remove the legrest simply pull upward.

  • Page 69: Adjusting The Length

    8.9.1.2 Adjusting the length Pre-requisites: • 1x 5 mm hexagon socket spanner • Loosen the screw (1) using the Allen key, but do not remove completely. • Set the legrest to the desired length. • Re-tighten the screw.

  • Page 70: Standard Footrest With Pre-Set Angle

    8.9.2 Standard footrest with pre-set angle 8.9.2.1 Swivelling the footrest outward and/or removing The small unlocking button is located on the upper section of the footrest. When the footrest is unlocked, it can be swivelled inward or outward when getting into the wheelchair as well as being removed completely.

  • Page 71: Setting The Angle

    8.9.2.2 Setting the angle PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground! Pre-requisites: •...
  • Page 72 • Loosen the screw (1) using the Allen key. • Set the desired angle. • Re-tighten the screw.

  • Page 73: Setting The End Stop Of The Footrest

    8.9.2.3 Setting the end stop of the footrest Pre-requisites: • 1x 6 mm Allen key • 1x 10 mm open-ended spanner The end position of the footrest is determined by means of a rubber stop (1). The rubber stop can be screwed in or out (A) or pushed up or down (B).
  • Page 74 • Use the Allen key to loosen the screw (1) and swivel the footrest upward in order to access the rubber stop. • Use the open-ended spanner to loosen the counternut (1).
  • Page 75 • Move the rubber stop to the desired position • Re-tighten the counternut • Move the footrest to the desired position. • Re-tighten the screw.

  • Page 76: Adjusting The Length Of The Footrest

    8.9.2.4 Adjusting the length of the footrest PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground! Pre-requisites: •...

  • Page 77: Manually Height Adjustable Legrest 90° - 0

    8.9.3 Manually height adjustable legrest 90° - 0° 8.9.3.1 Swivelling the legrest outward and/or removing The small unlocking button is located on the upper section of the legrest. When the legrest is unlocked, it can be swivelled inward or outward when getting into wheelchair as well as being removed completely.

  • Page 78: Setting The Angle

    8.9.3.2 Setting the angle PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground! •...
  • Page 79 • Hit the knob to release the locking mechanism. • Set the desired angle.
  • Page 80 • Turn the knob clockwise to tighten it.

  • Page 81: Setting The End Stop Of The Legrest

    8.9.3.3 Setting the end stop of the legrest Pre-requisites: • 1x 10 mm open-ended spanner The end position of the legrest is determined by means of a rubber stop (A). The rubber stop can be screwed in or out (A) or pushed up or down (B).
  • Page 82 • Loosen the locking knob (1) counter-clockwise at least one turn. • Hit the knob to release the locking mechanism.
  • Page 83 • Swivel the legrest upward in order to access the rubber stop. • Use the open-ended spanner to loosen the counternut (1).
  • Page 84 • Move the rubber stop to the desired position • Re-tighten the counternut • Move the legrest to the desired position. • Re-tighten the locking knob.

  • Page 85: Adjusting The Length Of The Legrest

    8.9.3.4 Adjusting the length of the legrest PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground! Pre-requisites: •...

  • Page 86: Adjusting The Depth Of The Calf Plate

    8.9.3.5 Adjusting the depth of the calf plate The depth of the calf plate can be adjusted via the holding plate. The holding plate hole combinations allow 5 different depth settings. Pre-requisites: • 1x 10 mm open-ended spanner • Use the open-ended wrench to loosen the nut (1) and remove.

  • Page 87: Adjusting The Height Of The Calf Pad

    8.9.3.6 Adjusting the height of the calf pad Pre-requisites: • 1x 4 mm Allen key • Use the Allen key to loosen the screws (1). • Adjust to the desired position. • Re-tighten the screws.

  • Page 88: Unlocking And Swivelling The Calf Plate Backward When Alighting

    8.9.3.7 Unlocking and swivelling the calf plate backward when alighting • Press the calf plate straight down. • Unlock the legrest and swivel outward. The calf plate swivels backward on its own.

  • Page 89: Adjusting The Angle Adjustable Foot Plate

    • Lift leg over the heel strap and place on the ground. 8.9.3.8 Adjusting the angle adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen both set screws on the foot plate. •...

  • Page 90: Adjusting The Angle And Depth Adjustable Foot Plate

    8.9.3.9 Adjusting the angle and depth adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen the set screw on the foot plate (1). • Adjust the foot plate to the desired angle or depth.

  • Page 91: Manually Height Adjustable Legrest 80° - 0° With Ergonomic Length Adjustment

    8.9.4 Manually height adjustable legrest 80° - 0° with ergonomic length adjustment 8.9.4.1 Swivelling the legrest outward and/or removing The small unlocking button is located on the upper section of the legrest. When the legrest is unlocked, it can be swivelled inward or outward when getting into wheelchair as well as being removed completely.

  • Page 92: Setting The Angle

    8.9.4.2 Setting the angle PLEASE NOTE: Danger of crushing! • Do not reach inside the swivelling range of the legrest! PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground! •...
  • Page 93 • Lowering: Keep the legrest in the foot plate area, pull the lateral adjusting lever (1) and lower the legrest slowly.

  • Page 94: Adjusting The Length Of The Legrest

    8.9.4.3 Adjusting the length of the legrest PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground! Pre-requisites: •...

  • Page 95: Adjusting The Depth Of The Calf Plate

    8.9.4.4 Adjusting the depth of the calf plate The depth of the calf plate can be adjusted via the holding plate. The holding plate hole combinations allow 5 different depth settings. Pre-requisites: • 1x 10 mm open-ended spanner • Use the open-ended wrench to loosen the nut (1) and remove.

  • Page 96: Adjusting The Height Of The Calf Pad

    8.9.4.5 Adjusting the height of the calf pad Pre-requisites: • 1x 4 mm Allen key • Use the Allen key to loosen the screws (1). • Adjust to the desired position. • Re-tighten the screws.

  • Page 97: Unlocking And Swivelling The Calf Plate Backward When Alighting

    8.9.4.6 Unlocking and swivelling the calf plate backward when alighting • Press the calf plate straight down. • Unlock the legrest and swivel outward. The calf plate swivels backward on its own.

  • Page 98: Adjusting The Angle Adjustable Foot Plate

    • Lift leg over the heel strap and place on the ground. 8.9.4.7 Adjusting the angle adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen both set screws on the foot plate. •...

  • Page 99: Adjusting The Angle And Depth Adjustable Foot Plate

    8.9.4.8 Adjusting the angle and depth adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen the set screw on the foot plate (1). • Adjust the foot plate to the desired angle or depth.

  • Page 100: Electrically Height Adjustable Legrest 80° - 0° With Ergonomic Length Adjustment

    8.9.5 Electrically height adjustable legrest 80° - 0° with ergonomic length adjustment 8.9.5.1 Swivelling the legrest outward and/or removing The small unlocking button is located on the upper section of the legrest. When the legrest is unlocked, it can be swivelled inward or outward when getting into wheelchair as well as being removed completely.

  • Page 101: Setting The Angle

    8.9.5.2 Setting the angle PLEASE NOTE: Danger of crushing! • Do not reach inside the swivelling range of the legrest! PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground! The electrically height adjustable legrest is operated via the remote.

  • Page 102: Adjusting The Length Of The Legrest

    8.9.5.3 Adjusting the length of the legrest PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that the legrests contact neither the castor wheels nor the ground! Pre-requisites: •...

  • Page 103: Adjusting The Depth Of The Calf Plate

    8.9.5.4 Adjusting the depth of the calf plate The depth of the calf plate can be adjusted via the holding plate. The holding plate hole combinations allow 5 different depth settings. Pre-requisites: • 1x 10 mm open-ended spanner • Use the open-ended wrench to loosen the nut (1) and remove.

  • Page 104: Adjusting The Height Of The Calf Pad

    8.9.5.5 Adjusting the height of the calf pad Pre-requisites: • 1x 4 mm Allen key • Use the Allen key to loosen the screws (1). • Adjust to the desired position. • Re-tighten the screws.

  • Page 105: Unlocking And Swivelling The Calf Plate Backward When Alighting

    8.9.5.6 Unlocking and swivelling the calf plate backward when alighting • Press the calf plate straight down. • Unlock the legrest and swivel outward. The calf plate swivels backward on its own.

  • Page 106: Adjusting The Angle Adjustable Foot Plate

    • Lift leg over the heel strap and place on the ground. 8.9.5.7 Adjusting the angle adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen both set screws on the foot plate. •...

  • Page 107: Adjusting The Angle And Depth Adjustable Foot Plate

    8.9.5.8 Adjusting the angle and depth adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen the set screw on the foot plate (1). • Adjust the foot plate to the desired angle or depth.

  • Page 108: Adjusting And Removing The Tray

    8.10 Adjusting and removing the tray CAUTION: Injury hazard or material damage if a power wheelchair which is fitted with a table is transported in a vehicle! • If a table is fitted, always remove it before transporting the wheelchair. 8.10.1 Laterally adjusting the tray •...

  • Page 109: 8.10.2 Adjusting The Depth Of The Tray / Removing The Tray

    8.10.2 Adjusting the depth of the tray / removing the tray • Loosen the wing-screw (1). • Adjust the table to the desired depth (or remove it entirely). • Re-tighten the screw. 8.10.3 Swinging the tray away to the side The tray can be swivelled up and away to the side to allow the user to get in and out of the mobility device CAUTION! Risk of injury! When the tray is raised it does not lock in place in this position!
  • Page 110 The tray can be swivelled upwards and pushed to the side as illustrated to enable getting on and off.

  • Page 111: Electrical System

    Electrical system Electronics protection system The vehicle's electronics are equipped with an overload-protection system. If the motors are put under considerable strain for a longer period of time (for example, when driving up a steep hill) and especially when the ambient temperature is high, then the electronic system could overheat.

  • Page 112: The Main Fuse

    9.1.1 The main fuse All the electrical equipment fitted to the wheelchair is protected against overload by the main fuse. The main fuse is located on the device support. In order to access the main fuse, you must first remove the battery cover.

  • Page 113: Batteries

    Batteries Power is supplied by two 12 V batteries. The batteries are maintenance-free and only need regular charging. In the following, you find information on how to charge, handle, transport, store, maintain, and use batteries. 9.2.1 Charging the batteries 9.2.1.1 General information on charging New batteries should always be fully charged once before their first use.

  • Page 114: How To Charge The Batteries

    10 °C. • Use only charging devices in Class 2. This class of chargers may be left unattended during charging. All charging devices which are supplied by Invacare® comply with these requirements. •...

  • Page 115: How To Disconnect The Batteries After Charging

    Risk of explosion and destruction of batteries if the wrong battery charger is used! • Only ever use the battery charger supplied with your vehicle, or a charger that has been approved by Invacare®. Risk of electric shock and damage to the battery charger if it gets wet! •...

  • Page 116: Storage And Maintenance

    9.2.2 Storage and Maintenance Follow the instructions listed below to ensure safe use and longevity of the batteries: • Always store the batteries fully charged. • Do not leave the batteries in a low state of charge for an extended length of time. Charge a discharged battery as soon as possible.
  • Page 117 The last 3 LED (two red and one orange) mean a remaining capacity of about 15 %. • Driving with blinking red LED’s means an extreme stress for the battery and should be avoided under normal circumstances. • When only one red LED is blinking, the Battery Safe feature is enabled. From this time, speed and acceleration is reduced drastically.

  • Page 118: Transporting Batteries

    • Under normal operation, once a month the battery should be discharged until all green and orange LED are off. This should be done within one day. A 16 hour charge afterwards is necessary as reconditioning. 9.2.4 Transporting batteries The batteries supplied with your electric vehicle are not hazardous goods. This classification is based on the German GGVS Hazardous Goods Road Transport Ordinances, and the IATA/DGR Hazardous Goods Rail Transport / Air Transport Ordinances.
  • Page 119 Only ever transport damaged batteries in an appropriate acid-resistant receptacle. • Wash all objects that have come into contact with acid with lots of water. Disposing of dead or damaged batteries correctly Dead or damaged batteries can be given back to your dealer or directly to Invacare®.

  • Page 120: Removing The Batteries

    9.2.5.3 Removing the batteries Requirements: • Phillips screwdriver • Spanner 11 mm • Remove battery cover. • Remove plastic clips (1) and remove device support upwards to the rear.
  • Page 121 • Pull the battery terminal caps upwards and push them back to allow access to the battery terminals. • Loosen the battery terminal clamps (2) with the spanner. • Swivel the device support upwards (it may be necessary to loosen the additional connection plug). •...

  • Page 122: Care And Maintenance

    Maintenance encompasses different areas, such as everyday care and cleaning, inspection checks, repair tasks and refurbishment. NOTE: Have your vehicle checked once a year by an authorised Invacare® dealer in order to maintain it's driving safety and roadworthiness. 10.1...

  • Page 123: Inspection Checks

    Service Manual for this device, which can be obtained from Invacare®. That Manual, however, is intended to be used by trained and authorised service technicians, and describes tasks which are not intended to be performed by...
  • Page 124 Maintenance Jobs Seat and backrest padding: - Check for perfect condition. Side part and armrest: - Are all fastening elements installed? - Can armrests / side parts be removed and installed without too much physical effort? - Are armrests secured in their positions? Legrests: - Do legrests lock into place without any problem? (Only applies to detachable legrests)
  • Page 125 Maintenance Jobs Electronics / Electrical System: - Check all plug connections for condition and firm seat. - Have all batteries been fully charged before the daily operation? Before every trip - Are all holders, screws firmly fixed, tight and safe? - Are all electric bulbs of the lighting system (if applicable) in working Before each trip order?

  • Page 126: Repair Instructions

    "Technical specifications" on page 149, or consult the Service Manual, available from Invacare® (in this connection please see the addresses and phone numbers in section "How can you get in touch with Invacare®?" on page 3). In case you require assistance, please contact your Invacare® Dealer.

  • Page 127: Repairing A Flat Tyre (Front)

    11.1.1 Repairing a flat tyre (front) Requirements: • Allen key 5 mm • Open-end spanner 24 mm • Repair kit for inner tubes or a new inner tube. • Talcum powder Remove the wheel • Jack the vehicle up and place a block of wood underneath it to prop it up.
  • Page 128 Repair the flat tyre EXPLOSION HAZARD! The wheel explodes if the air is not left out before dismantling! • It is imperative that you let the air out of the tyre before dismantling it (press the pin in the middle of the valve downwards)! •...
  • Page 129 • Place the rim halves in the tyre from the outside. • Pump up the tyre a little. • Re-position the Allen screws in the rim and tighten them firmly. Make sure the inner tube does not get pinched between the rims halves! •...

  • Page 130: Repairing Punctures (Drive Wheel With Gb Motor And Pneumatic Tyres)

    11.1.2 Repairing punctures (drive wheel with GB motor and pneumatic tyres) EXPLOSION HAZARD! The wheel will explode if you do not let the air out of the tyre before removing the wheel! • Always let the air out of the tyre before removing it (press in the pin in the middle of the valve)! Injury hazard!If the wheel has been insufficiently tightened during assembly, it can become loosened during driving!
  • Page 131 Disassembly • Block up the vehicle (place wooden blocks under frame). • Unscrew valve cap. • Depressurise tyre by pressing in the pin in the valve (1). • Unscrew 5 screws (2). • Remove the wheel rim halves. • Remove the inner tube from the tyre. NOTE: If the old inner tube is to be repaired and re-used, and has become wet during repair, you can make replacement easier by sprinkling the inner tube with a little talcum powder.
  • Page 132 • Repair inner tube and replace, or insert new. • Replace the inner tube in the tyre. • Insert the wheel rim halves once again. • Insert the screws and tighten slightly. • Pump a little air into the inner tube. •...

  • Page 133: Repairing Punctures (Drive Wheel With Conventional Motor And Pneumatic Tyres)

    11.1.3 Repairing punctures (drive wheel with conventional motor and pneumatic tyres) Injury hazard! If the wheel has been insufficiently tightened during assembly, it can become loosened during driving! • When reassembling the drive wheels, tighten the Allen screws at a torque of 30 Nm! •...
  • Page 134 Removing the wheel • Block up the vehicle (place wooden blocks under frame). • Unscrew 4 screws (1). • Remove the wheel from the hub. NOTE: Re-assembly is done in reverse order. Ensure that the tyre is replaced on the same side and in the same travel direction as it was previously mounted.
  • Page 135 Repairing the flat tyre EXPLOSION HAZARD! The wheel will explode if the pressure is not released from the tyre before disassembling the wheel rim! • Always make sure to completely release the air pressure by pressing the pin in the centre of the valve! •...
  • Page 136 • Insert the wheel rim halves from outside into the tyre. • Pump a little air into the inner tube. • Insert the cylinder head screws in the rim and tighten to 10 Nm. Make sure the inner tube does not get pinched between the rims halves! •...

  • Page 137: Transport

    Transport CAUTION: Injury hazard or material damage if a power wheelchair which is fitted with a table is transported in a vehicle! • If a table is fitted, always remove it before transporting the wheelchair. 12.1 Transferring the wheelchair to a vehicle WARNING: The wheelchair is in danger of tipping over if it is transferred to a vehicle while the driver is still seated in the wheelchair! •...

  • Page 138: Use Of The Wheelchair As A Seat In A Vehicle

    • An alternative way to safely use this wheelchair as a vehicle seat may be by using the Docking Station system if the wheelchair is compatible with that system, available separately! Please contact Invacare if you require the details. WARNING: Danger of injury or damage to the wheelchair or to the transporting vehicle, if the legrests are in a raised position while the wheelchair is used as a vehicle seat! •...
  • Page 139 Caution: There is a danger of injury if the wheelchair is not properly secured during use as a vehicle seat! • If possible, the user should always leave the wheelchair to use a vehicle seat and the safety belts provided with the vehicle. •...
  • Page 140 (UK for example), but may also be obtained from Invacare® as an option in other countries. This power wheelchair complies with the requirements of ISO 7176-19:2001 and may be used as a vehicle seat in connection with an anchoring system that has been checked and approved in accordance with ISO 10542.

  • Page 141: 12.2.1 How The Wheelchair Is Anchored In A Vehicle For Use As A Vehicle Seat

    12.2.1 How the wheelchair is anchored in a vehicle for use as a vehicle seat The power wheelchair is fitted with four anchoring points, which are labelled with the symbol shown on the right. Snap hooks or belt loops can be used for fixation.

  • Page 142: 12.2.2 How The User Is Secured Within The Wheelchair

    12.2.2 How the user is secured within the wheelchair CAUTION: There is a danger of injury if the user is not properly secured within the wheelchair! • Even if the wheelchair is fitted with a postural belt, this is no substitute for a proper safety belt which complies with ISO 10542 in the transport vehicle.
  • Page 143 This can cause the neck to be hyperextended during collisions! • A headrest must be installed! The headrest optionally supplied for this mobility device by Invacare® is perfectly suitable for use during transport. • The headrest must be adjusted to the user's ear height.
  • Page 144 Seat belts may not be held at a distance The pelvic belt should be positioned in the from the user's body using parts of the area between the user's pelvis and thighs wheelchair such as armrests or wheels. so that it is unobstructed and not too loose. The ideal angle of the pelvic belt to the horizontal is between 45°...
  • Page 145 The safety belt installed in the transporting vehicle should be applied as shown in the illustration at right. 1) Centre line of the body 2) Centre of the sternum...

  • Page 146: Securing The Wheelchair For Transport Without Passengers

    Securing the wheelchair for transport without passengers CAUTION: Injury hazard! ® • If you are unable to fasten your electric wheelchair securely in a transport vehicle, Invacare recommends that you do not transport it! • Before transporting your wheelchair, make sure the motors are engaged and that the Joystick Box is switched off.

  • Page 147: Refurbishment

    Cleaning and disinfection. Please see chapter "Care and maintenance" on page 122. • Inspection according to service plan. Please consult service instructions, available from Invacare®. • Adaptation to the user. Please see chapter "Adjusting the wheelchair to the user's seating...

  • Page 148: Disposal

    Electric components and printed circuit boards are disposed of as electronic scrap. • Exhausted or damaged batteries can be returned to your medical equipment supplier or Invacare®. • Disposal must be carried out in accordance with the respective national legal provisions.

  • Page 149: Technical Specifications

    Temperature range for operation according to ISO 7176-9: • -25° … +50 °C Temperature range for storage according to ISO 7176-9: • -40° … +65 °C Electrical system Storm³ with conventional motors Storm³ with GB motors Motors • 220 W (6 km/h) • 500 W (12 km/h) •...
  • Page 150 • approx. 37 km with 350 W motors Storm³ with GB motors • approx. 57 km Storm³ BLU with 10 km/h motors and 60 Ah batteries • approx. 32 km Storm³ BLU with 6 km/h motors and 50 Ah batteries •...
  • Page 151 Dimensions Standard Contour Recaro Flex Overall length (without legrests, • 990 mm with kerb climber) Seat height **** • 440 mm Seat width (armrest adjustment • 430 mm • 480 mm • 360 mm • 380 mm range in brackets) (440 - 480 (490 - 530 (490 - 530...
  • Page 152 **** Measured without seat cushion ***** The actual kerb weight depends on the fittings your mobility aid has been supplied with. Every Invacare® mobility aid is weighed when leaving the works. Please refer to the nameplate for the kerb weight (including batteries) measured.

  • Page 153: Inspections Performed

    It is confirmed by stamp and signature that all jobs listed in the inspection schedule of the Service and Repair Instructions have been properly performed. The list of the inspection jobs to be performed can be found in the Service Manual which is available through Invacare®. Delivery Inspection...

Table of Contents