Advertisement
Quick Links
SAVE THESE INSTRUCTIONS
NOTE: Check ALL parts for shipping damage. If ship-
ping damage is noted, DO NOT use. Contact Carrier/
Dealer for further instructions.
SAFETY SUMMARY
The following recommendations are made for the
safe use of the Invacare I.V. Stand:
GENERAL WARNINGS
DO NOT install this equipment without first
reading and understanding this instruction
sheet. If you are unable to understand these
Warnings, Cautions and Instructions, con-
tact a healthcare professional, dealer or
technical personnel if applicable before at-
tempting to install this equipment - other-
wise, injury or damage may occur.
SPECIFIC WARNINGS
Always inspect the I.V. stand to ensure that
it is properly positioned and is stable be-
fore using.
After ANY adjustments, repair or service
and BEFORE use, make sure all attaching
hardware is tightened securely - otherwise
injury or damage may occur.
NOTE: Model 6681-5 and 6845-5 I.V. stands are pack-
aged in pairs. There are enough parts to construct two (2)
complete I.V. stands.
Each package includes the following items:
DESCRIPTION
6681-5
I.V. Hanger
Upper I.V. tube
Lower I.V. tube
Base
Upper Base Half
Lower Base Half
Caster
Bolt
Small Steel Washer
Locking Washer
Black Plastic Insert
Large Steel Washer
Adjusting Knob
Washer
Locknut
Wrench
QUANTITY
6845-5
6845
2
2
2
2
2
2
2
2
N/A
N/A
N/A
N/A
N/A
10
10
2
2
2
2
2
2
N/A
2
2
N/A
2
2
2
2
N/A
N/A
N/A
N/A
N/A
N/A
ASSEMBLING THE BASE (FIGURE 1)
Models 6681-5 and 6845-5
1. Place base upside down.
2. Align a caster stem with a mounting hole in the base.
3. Firmly push down on bottom of caster until caster
stem snaps into mounting hole.
NOTE: Pressure MUST be applied on the correct area or
the caster will not insert properly.
4. Repeat STEPS 2-3 for remaining four (4) casters.
Model 6845
1. Position the upper base half and lower base half as
shown in FIGURE 1.
NOTE: The lower base half has a recess in the center.
2. Install one (1) washer onto one (1) caster stem.
3. Insert caster stem UP through mounting hole in base.
4. Install locknut onto caster stem. Tighten securely us-
ing wrench provided.
5. Repeat STEPS 2-4 for remaining three (3) casters.
MODELS 6681-5
AND 6845-5
Caster
1
1
1
1
MODEL 6845
1
4
1
1
1
1
Recess
4
Upper
4
Base Half
1
FIGURE 1 - ASSEMBLING THE BASE
over
Bottom of Caster
(APPLY PRESSURE
HERE)
Caster
Stem
Mounting
Hole
Base
Locknut
Lower
Base Half
Caster
Mounting
Hole
Washer
Caster
Stem
Advertisement
Related Manuals for Invacare 6681-5
Summary of Contents for Invacare 6681-5
-
Page 1: Safety Summary
BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may occur. NOTE: Model 6681-5 and 6845-5 I.V. stands are pack- aged in pairs. There are enough parts to construct two (2) complete I.V. stands. - Page 2 ASSEMBLING THE I.V. STAND (FIGURE 2) 1. Perform one (1) of the following: A. MODELS 6681-5 AND 6845-5 - 1. Place black plastic insert into the hole pro- vided on top of the base. 2. Insert the lower I.V. tube through the black plas- tic insert and the base.