Kenwood KVT-839DVD Installation Manual
  1. Manuals
  2. Brands
  3. Kenwood Manuals
  4. Car Receiver
  5. KVT-839DVD
  6. Installation manual
Kenwood KVT-839DVD Installation Manual

Kenwood KVT-839DVD Installation Manual

Monitor with dvd receiver
Hide thumbs Also See for KVT-839DVD:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual, Instruction Manual
MONITOR WITH DVD RECEIVER
KVT-839DVD

INSTALLATION MANUAL

© B54-4557-00/00 (MV/XV)

Advertisement

Table of Contents
loading

Related Manuals for Kenwood KVT-839DVD

Summary of Contents for Kenwood KVT-839DVD

  • Page 1: Installation Manual

    MONITOR WITH DVD RECEIVER KVT-839DVD INSTALLATION MANUAL © B54-4557-00/00 (MV/XV)
  • Page 2 Accessories ..1 ..2 ..1 ..4 ..1 ..4 ..1 ..2 ..1 ..1 ..2 ..4 ..4 KVT-839DVD...

  • Page 3: Installation Procedure

    Installation Procedure ¤ 1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. • If the power is not turned ON (or it is ON, but will be OFF 2. Make the proper input and output wire immediately), the speaker wire may have a short-circuit connections for each unit.
  • Page 4 Connect to the terminal that is grounded when either the telephone rings or during conversation. Mute wire (Brown) To connect the Kenwood navigation system, consult your navigation manual. Depending on what antenna you are using, Motor antenna control wire (Blue) connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna.
  • Page 5 Receiver unit Accessory # The cable (Accessory 3) is fixed with a chassis using Accessory 3 harness band (Accessory Receiver unit FM/AM antenna input Wiring harness (Accessory 1) REVERSE White/Black ILLUMI To front left speaker White Gray/Black REMO.CONT To front right speaker Gray MUTE Green/Black...

  • Page 6: System Connection

    • Visual input (Yellow) • Audio left input (White) • Audio right input (Red) ■ Rear View Camera Input • Visual input (Yellow) ■ Audio/Visual Output • Visual output (Yellow) • Audio left output (White) • Audio right output (Red) KVT-839DVD...

  • Page 7: Optional Accessory Connection

    Optional Accessory Connection iPod (commercially available) KCA-iP300V (Optional Accessory) Audio Input Resistance-free stereo type mini plug (3.5Ф) Audio Output (Black) Visual Input Monitor/Player unit Resistance-free mini plug (3.5Ф) Visual Output (Yellow) USB terminal USB terminal (iPod) iPod cannot be connected. USB terminal Receiver unit Accessory 3...
  • Page 8 8. Sems bolts (M4 × 8 mm) (Accessory 8) 2. Use the tapping screw 9 to secure the receiver Tapping screw (ø4 × 16 mm) unit to the audio board. (Accessory 9) KVT-839DVD...

  • Page 9: Removing The Unit

    Removing Monitor/Player Unit Removing the Hard Rubber Frame Removing the Unit (escutcheon) 1. Remove the hard rubber frame by referring to the removal procedure in the section <Removing the 1. Engage the catch pins on the removal tool 7 and Hard Rubber Frame>.

  • Page 10: Installing In Japanese-Made Cars

    Screws (included in audio unit package) Screws (included in audio unit package) Audio unit or others ⁄ • Do not use your own screws. Use only the screws provided. If you use the wrong screws, you could damage the unit. KVT-839DVD...
  • Page 11 Installation on Toyota Car using Brackets at Holes shown by "●" When using the bracket shown above, you cannot use screws at two holes of the right and left unit sides. 1. Mount the bracket at each side. Car Bracket Accessory ! (M5x6mm) Accessory ! (M5x6mm) Screws (included in...

Table of Contents