Installation Procedure 1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the speaker wires of the wiring harness. 4.
Connection 2WARNING If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. Do not connect.
Page 5
Wiring harness (Accessory 1) Connect to the terminal that is grounded when either the telephone rings or during conversation. MUTE NOTE To connect the KENWOOD navigation system, consult your navigation manual. White/Black To front left speaker White Gray/Black To front right speaker...
Connection System Connection Receiver unit (front side) PREOUT TO TV TUNER I/F ANTENNA OUTPUT INPUT MONITOR 6 English TO NAVIGATION I/F TO 5L-I/F • Front Preout FRONT Audio left output (White) Audio right output (Red) • Rear Preout REAR Audio left output (White) Audio right output (Red) •...
Installation Installation for Monitor/Player Unit Firewall or metal support Screw (M4X8) (commercially available) Self-tapping screw (commercially available) Metal mounting strap (commercially available) Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). Installation for Receiver unit 1.
Installation Installing in Japanese-Made Cars Installing on Toyota, Nissan or Mitsubishi Car Using Brackets at Holes shown by "¶" Accessory - or = Screws (included in audio unit package) 8 English Bracket Audio unit or others Accessory - or = Screws (included in audio unit package)
Page 9
Installation on Toyota Car using Brackets at Holes shown by "¶" When using the bracket shown above, you cannot use screws at two holes of the right and left unit sides. If so, tighten the bracket using accessories 0 as shown below. 1.
Page 10
Installation Removing Monitor/Player Unit Removing the Hard Rubber Frame (escutcheon) 1. Engage the catch pins on the removal tool 6 and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure.
Page 32
설치하기 설치하기 전에 전에 설치하기 설치하기 전에 설치하기 전에 전에 부속품 부속품 부속품 부속품 부속품 32 한 한 한 한 한 글 글 글 글 글 ... 1 ... 1 ... 1 ... 1 ... 1 ... 2 ... 4 ...
Page 33
설치 설치 순서 설치 순서 순서 순서 설치 설치 순서 1. 단락을 방지하기 위해 이그니션에서 키를 빼고 - 배터리 를 차단합니다. 2. 각 기기의 입출력 와이어를 바르게 접속합니다. 3. 와이어링 하네스와 스피커 와이어를 접속합니다. 4. 어스,배터리,이그니션의 순서로 와이어링 하네스의 와 이어를...
Page 34
접속 접속 접속 접속 접속 2경고 이그니션 와이어 (빨강) 와 배터리 와이어 (노랑) 를 차대 (접지) 에 연결할 때에 전기 누전을 일으켜 발화할 수도 있습니다. 이들 와이어는 항상 휴즈 박스를 관통하는 전원 소스에 연결하십시오. 연결하지 마십시오 제공되는 릴레이 단자를 사용해서 자동차의 주차 브레이크...
Page 35
후면 후면 후면) ) ) ) ) POWER 와이어링 하네스 (부속품 1) 전화 호출 또는 대화중 접지된 단자에 접속합니다. MUTE 주의 KENWOOD네비게이션 시스템을 연결하기위해서는 네비게이션 메뉴얼을 참조하십시오. 흰색/검은색 앞 왼쪽 스피커 흰색 회색/검은색 앞 오른쪽 스피커 회색 녹색/검은색 뒤 왼쪽 스피커...
Page 36
접속 접속 접속 접속 접속 시스템 연결 시스템 시스템 연결 연결 연결 시스템 시스템 연결 PREOUT TO TV TUNER I/F ANTENNA OUTPUT INPUT MONITOR 36 한 한 한 한 한 글 글 글 글 글 리시버 기기 리시버 리시버 리시버 리시버...
Page 37
설치 설치 설치 설치 설치 모니터 모니터/ / / / / 플레이어 모니터 플레이어 플레이어 기기를 플레이어 기기를 위한 기기를 기기를 모니터 모니터 플레이어 기기를 방화벽 또는 메탈 서포트 나사 (M4 × 8) (상용) 자기-탭핑 나사(상용) 기기가 제자리에 단단히 설치되었는지 확인하십시오. 기기가 불안정 하면, 오작동할...
Page 38
설치 설치 설치 설치 설치 일제 일제 자동차에 일제 자동차에 자동차에 자동차에 설치하기 설치하기 설치하기 설치하기 일제 일제 자동차에 설치하기 • • • • • “ ”의 의 의 의 의 구멍에 구멍에 브래킷을 구멍에 구멍에 브래킷을 사용하는 브래킷을 브래킷을 구멍에...
Page 39
• • • • • “ ”의 의 의 의 의 구멍에 구멍에 구멍에 브래킷을 구멍에 브래킷을 사용하는 브래킷을 브래킷을 사용하는 사용하는 토요타 사용하는 구멍에 브래킷을 사용하는 위와같은 브래킷을 사용하는 경우에는 기기의 좌우측의 두 구멍에 사용하는 나사를 사용할 수 없습니다. 이런 경우에는 아 래의...
Page 40
설치 설치 설치 설치 설치 모니터 모니터/ / / / / 플레이어 모니터 플레이어 플레이어 플레이어 기기 모니터 모니터 플레이어 강화 고무 강화 강화 고무 고무 고무 프레임 프레임 프레임 프레임 떼어내기 떼어내기 떼어내기 떼어내기 강화 강화 고무 프레임 떼어내기 1.