Specifications (Dtr-6.4) - Integra DTR-6.4/5.4 Instructional Manual

Specifications
AMPLIFIER SECTION
Continuous average power output (FTC)
All channels:
Continuous power output (DIN)
Maximum power output (EIAJ)
Dynamic power output (stereo)
Total harmonic distortion:
IM distortion:
Damping factor:
Input sensitivity and impedance
PHONO:
LINE (CD, TAPE, DVD,
VIDEO 1-4):
MULTICHANNEL INPUT
(FRONT L/C/R, SURROUND
L/R):
(SUBWOOFER):
COAXIAL (DIGITAL):
DVD, VIDEO 1, 2, 3, 4:
COMPONENT VIDEO 1, 2:
Output level and impedance
Rec out (TAPE, VIDEO 1, 2):
Line out:
Pre out:
VIDEO (VIDEO 1, 2,
MONITOR OUT):
COMPONENT VIDEO OUT:
Phono overload:
Frequency response:
RIAA deviation:
Tone control
Bass:
Treble:
Signal-to-noise ratio (stereo)
Phono:
Line:
Muting:
74
(DTR-6.4)
100 W per channel min. RMS at 8 Ω,
2 channels driven from 20 Hz to 20
kHz with no more than 0.08% total
harmonic distortion.
125 W min. RMS at 6 Ω, 2 channels
driven from 1 kHz with no more
than 0.1% total harmonic distortion.
130 W at 6 Ω
160 W at 6 Ω
2 × 230 W at 3 Ω
2 × 170 W at 4 Ω
2 × 115 W at 8 Ω
0.08% at rated power
0.08% at 1 W output
0.08% at rated power
0.08% at 1 W output
60 at 8 Ω
2.5 mV, 47 kΩ
200 mV, 47 kΩ
200 mV, 47 kΩ
36 mV, 47 kΩ
0.5 Vp-p, 75 Ω
1 Vp-p, 75 Ω
1 Vp-p, 75 Ω (Y)
0.28 Vp-p, 75 Ω (C)
1 Vp-p, 75 Ω (Y)
0.7 Vp-p, 75 Ω (P
, P )
B R
200 mV, 470 Ω
100 mV, 470 Ω (Zone 2)
1 V, 470 Ω
1 Vp-p, 75 Ω
1 Vp-p, 75 Ω (Y)
0.28 p-p, 75 Ω (C)
1 Vp-p, 75 Ω (Y)
0.7 Vp-p, 75 Ω (P
, P )
B R
70 mV RMS at 1 kHz, 0.5% T.H.D.
10 Hz to 100 kHz: +1/–3 dB
(Direct mode)
20 Hz to 20 kHz: ±0.8 dB
±10 dB at 50 Hz
±10 dB at 20,000 Hz
80 dB (IHF A, 5 mV input, Direct mode)
106 dB (IHF A, 0.5 V input, Direct mode)
–50 dB
TUNER SECTION
FM
Tuning range:
Usable sensitivity
Mono:
Stereo:
50 dB quieting sensitivity
Mono:
Stereo:
Capture ratio:
Image rejection ratio
USA & Canadian models:
Australian models:
IF rejection ratio:
Signal-to-noise ratio
Mono:
Stereo:
Alternate channel attenuation:
Selectivity:
AM suppression ratio:
Total harmonic distortion
Mono:
Stereo:
Frequency response:
Stereo separation:
AM
Tuning range
USA & Canadian models:
Australian models:
Usable sensitivity:
Image rejection ratio:
IF rejection ratio:
Signal-to-noise ratio:
Total harmonic distortion:
GENERAL
Power supply
USA & Canadian models:
Australian models:
Power consumption
USA & Canadian models:
Australian models:
Dimensions (W × H × D):
Weight
USA & Canadian models:
Australian models:
REMOTE CONTROLLER
Transmitter:
Signal range:
Power supply:
Specifications and features are subject to change without notice.
87.5–108.0 MHz (50-kHz steps)
Ω
11.2 dBf, 1.0 µV (75 IHF)
Ω
0.9 µV (75 DIN)
Ω
17.2 dBf, 2.0 µV (75 IHF)
Ω
23 µV (75 DIN)
Ω
17.2 dBf, 2.0 µV (75 )
Ω
37.2 dBf, 20 µV (75 )
2.0 dB
40 dB
85 dB
90 dB
76 dB
70 dB
55 dB
50 dB (DIN)
50 dB
0.2%
0.3%
30 Hz–15 kHz, ±1.0 dB
45 dB at 1 kHz
30 dB at 100 Hz–10 kHz
530 to 1,710 kHz (10-kHz steps)
522 to 1,611 kHz (9-kHz steps)
30 µV
40 dB
40 dB
40 dB
0.7%
AC 120 V, 60 Hz
AC 230–240 V, 50 Hz
6.0 A
620 W
17-1/8" × 6-7/8" × 17"
435 × 175 × 432 mm
27.1 lbs. (12.3 kg)
13.1 kg (28.9 lbs.)
Infrared
Approx. 16 ft., 5 meters
Two "AA" batteries (1.5 V × 2)