Normal Playback; Preparing For Playback - Kenwood KRF-V6030D Instruction Manual

4
Input the distance to the speakers.
16
1
Distance to front speakers:
Distance to center speaker:
Distance to surround speakers:
2
The speaker indicator to be adjusted blinks.
SP A B TI.VOL
L C R
CLIP MUTE
LFE SW
RDS EON PTY
LS S RS
• The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustable TP TA NEWS
Indication in feet
in 1 foot (0.3 m) increments.
3
4 2 3
5
SP A B TI.VOL
L
CLIP MUTE
LFE
RDS EON PTY
LS
TP TA NEWS
Display when all speakers have been selected.
• The speakers you selected appear on the display. Confirm that all
the speakers have been correctly selected.
Input level adjustment (analog sources only)
If the input level of an analog source signal is too high, adjust the input
level.
1
• You can store a separate input level for each input source. If the
MONITOR function is on, you can store an input level for when
MONITOR is on independently of the input levels for the input
sources.
2
3
SP A B TI.VOL
L C R
CLIP MUTE
LFE SW
RDS EON PTY
LS S RS
TP TA NEWS
• The adjustment mode is displayed for approximately eight seconds.
• The input level may be adjusted to any one of three settings: 0,
-3, and -6. (The initial setting is 0.)
4
Preparing for surround sound
____ feet (meters)
____ feet (meters)
____ feet (meters)
FM AUTO SOUND
AM PRO LOGIC
MHz 3 STEREO
kHz DOWN MIX
Indication in meters
C R
SW
S RS
FM AUTO SOUND
AM PRO LOGIC
MHz 3 STEREO
kHz DOWN MIX

Normal playback

Preparing for playback

Some preparatory steps are needed before starting playback.
ON/STANDBY
DIGITAL AUTO POWER
S.DIRECT MEMO
MONITOR ST.
TUNED
DSP
Selecting the input mode
If you have selected a component connected to the
or
setting is correct for the type of audio signal to be used.
Selecting MD/TAPE
Select the source name corresponding to the component connected to
the MD/TAPE jacks. The initial factory setting is "
source name associated with the MD/TAPE jacks to "
steps below:
1
2
• The source indication changes to "
• To return to the original indication, repeat the above procedure.
• You also will need to change the name input to the remote control to
" ".
Selecting the speaker system (except for KRF-V5030D/
V4530D)
The indicator for the speakers
you want to use should be lit.
SP A B
CLIP
RDS EON
TP TA
DIGITAL AUTO
KRF-V7030D/V6030D
S.DIRECT MEMO
MONITOR ST.
DSP TUNED
• Activating a surround mode or selecting "DVD/6ch" as the input
source causes speaker system A to be selected automatically.
Turning on the receiver
1
2
INPUT MODE
AUTO
INPUT SELECTOR
SPEAKERS A/B
(KRF-V7030D only) jacks, make sure that the input mode
".
Sound from the speakers connected to the SPEAKERS A
terminals on the rear panel.
Sound from the speakers connected to the SPEAKERS B
terminals on the rear panel.
Sound from both the speakers connected to the SPEAKERS
A and B terminals on the rear panel.
No sound from the speakers. Use this setting when listening
with headphones for stereo sound and virtual surround in all
playback modes.
The speaker indicator lights.
TI.VOL SP
L C R
MUTE CLIP
LFE SW
PTY RDS EON
LS S RS
NEWS TP
KRF-V5030D/V4530D
0
". To change the
," follow the
1
A B TI.VOL
L C R
MUTE
LFE SW
PTY
LS S RS
TA NEWS