Auto Setup; Quick Guide For Menu Operation - Orion 26MT6000 Operating Instructions Manual

Auto setup

Your television has an Automatic Tuning
System which makes tuning in your television
easy. This Automatic tuning System scans
the entire reception range in your area and
automatically stores all available analogue and
digital channels of suitable signal strength
in the correct order.
Preparation:
Press (Power) on the unit or press
the remote.
1
Auto Installation menu will appear.
Press or to select desired language.
Then press
.
Auto Installation
Please select your language
then press "ENTER"
on your remote control:
2
Press or to select your country.
Then press
.
Auto Installation
Please select your country
then press "ENTER"
on your remote control:
3
Press or to select Home.
Then press
.
Auto Installation
Please select where the TV will be
placed.
The picture will be optimized for
that location.
4
If you cancel Auto Power Off (see page 20),
press or to select Off. Then press
Auto Installation
Your TV has been set to power off
after 4 hours of continuous viewing.
If you want to change this setting,
please choose Off.
This setting can also be changed in
the MENU.
5
TV will search for Digital TV-channels at first.
Connect your DVB-T antenna now.
Continue with ENTER to start auto tuning.
The tuning's progress will be displayed in
percent for confirmation.
Auto Installation
TV will search for Digital CH,
please connect aerial(RF) lead.
Press [ENTER] to start.
If you skip this step,
it can be installed at a later stage
in the MENU.
Note:
• Please be patient - the Auto Tuning process
can take several minutes to complete.
6
When the tuning for Digital TV-channels is
completed, you will be asked if you want
to proceed to autotuning for Analog TV-
channels. If you wish to start autotune Analog
TV-channels, connect your Analog cable-TV
antenna and press ENTER.
3BR2901A_EN.indd 11 3BR2901A_EN.indd 11
(On/Standby) on
Language
English
Deutsch
Français
Country
Australia
UK
Germany
TV Location
Home
Store
.
Auto Power Off
On
Off
Channel Scan
Scan
0%
Note:
• If you do not wish to carry out the autotuning for
Analog TV-channels, press RETURN to exit the menu.
Auto Installation
TV will search for Analogue CH,
please connect aerial(RF) lead.
Press [ENTER] to start.
If you skip this step,
it can be installed at a later stage
in the MENU.
100%
7
When the display reads 100%, press ENTER
to finish.
Note:
• To cancel the auto tuning, press RETURN during the
process.
THE AUTOMATIC TUNING PROCESS WILL
ONLY START BY ITSELF THE FIRST TIME YOU
SWITCH THE SET ON. HOWEVER YOU CAN
RESTART THIS PROCESS VIA THE MENU
SYSTEM (see page 12).

Quick guide for Menu operation

Make sure the antenna connection and power
supply are connected as per the description on
previous page.
Preparations:
• Turn on the unit with the (Power) button on the unit.
The (On/Standby) indicator will light up in blue.
Call Menu and for example: Select Auto Scan.
1
Press INPUT SELECT. Select TV. Press MENU.
2
Press or to select
3
Press or to select Channel Set Up, then press .
Picture
Audio
Setup
O i
• If the channel which Channel Block (P.16) was set
exits, password entering screen will appear. Then
enter the password.
4
Press or to select Auto Scan.
Picture
Audio
Setup
... on the following pages the MENU can be
called in the same way as here.
5
Press MENU to exit the menu.
Note:
• If no buttons are pressed for more than approx. 60
seconds, the Menu screen disappears automatically.
Channel Scan
Scan
then press .
11
3/8/11 12:14:08 PM 3/8/11 12:14:08 PM