Page 1 2003 Chevrolet Venture Owner Manual Seats and Restraint Systems ......1-1 Driving Your Vehicle ........4-1 Front Seats ..........1-3 Your Driving, the Road, and Your Vehicle ..4-2 Rear Seats ..........1-7 Towing ........... 4-32 Safety Belts ..........1-30 Service and Appearance Care ......
Page 2: How To Use This Manual
P.O. Box 07130 Detroit, MI 48207 GENERAL MOTORS, GM, the GM Emblem, How to Use This Manual CHEVROLET, the CHEVROLET Emblem and the name VENTURE are registered trademarks of General Many people read their owner’s manual from beginning Motors Corporation.
Page 3 Safety Warnings and Symbols You will also ﬁnd a circle with a slash through it in this book. This safety You will ﬁnd a number of safety cautions in this book. symbol means “Don’t,” We use a box and the word CAUTION to tell you about “Don’t do this”...
Page 4: Vehicle Symbols
Vehicle Damage Warnings Vehicle Symbols Also, in this book you will ﬁnd these notices: Your vehicle has components and labels that use symbols instead of text. Symbols, used on your vehicle, Notice: These mean there is something that could are shown along with the text describing the operation damage your vehicle.
Page 5 These are some examples of vehicle symbols you may ﬁnd on your vehicle:...
Page 6 NOTES...
Page 7: Seats And Restraint Systems
Section 1 Seats and Restraint Systems Front Seats ............1-3 Rear Safety Belt Comfort Guides for Manual Seats ..........1-3 Children and Small Adults ......1-52 Six-Way Power Seats ........1-4 Safety Belt Pretensioners .......1-54 Reclining Seatbacks ........1-4 Safety Belt Extender ........1-54 Head Restraints ..........1-6 Child Restraints ..........1-55 Rear Seats ............1-7 Older Children ..........1-55...
Page 8: Table Of Contents
Section 1 Seats and Restraint Systems Air Bag Systems ..........1-93 Restraint System Check ........1-103 Where Are the Air Bags? .......1-96 Checking Your Restraint Systems ....1-103 When Should an Air Bag Inﬂate? ....1-98 Replacing Restraint System Parts What Makes an Air Bag Inﬂate? .....1-99 After a Crash ..........1-104 How Does an Air Bag Restrain? .....1-99 What Will You See After an Air...
Page 9: Front Seats
Front Seats CAUTION: Manual Seats You can lose control of the vehicle if you try to Use the lever located on adjust a manual driver’s seat while the vehicle the front of the seat to is moving. The sudden movement could startle adjust the seat forward or and confuse you, or make you push a pedal rearward.
Page 10: Reclining Seatbacks
Six-Way Power Seats Reclining Seatbacks Your vehicle may have this feature. If it does, the six-way power seat control is located on the outboard sides of the driver’s and front passenger’s seats. • Move the front of the control up or down to adjust the front portion of the cushion up or down.
Page 11 CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can’t do their job when you’re reclined like this. The shoulder belt can’t do its job because it won’t be against your body.
Page 12: Head Restraints
Head Restraints Adjust your head restraint so that the top of the restraint is closest to the top of your head. This position reduces the chance of a neck injury in a crash. Head restraints are ﬁxed on some models and adjustable on others.
Page 13: Rear Seats
Rear Seats Flip and Fold Feature The rear seats in your vehicle can be folded forward. Use this feature for exiting and entering third row seats. Rear Seat Operation 1. If the seats have the adjustable head restraints, push them fully down. The rear seats in your vehicle have levers and straps used to adjust, remove and reinstall the seats.
Page 14: Split Bench Seats
Split Bench Seats To return the seat(s) to the normal position, do the following: If you have the split bench seat (50/50 or 40/60), the 1. Push the seat back and ﬁrmly push the rear hooks seatbacks can be folded forward or reclined individually onto the rear ﬂoor pins by pushing down on the and the seats can be removed individually.
Page 15: Second Row
Adjusting the Split Bench Seats The other lever is located on the rear of the seat. (Second Row) The second row bench seats are adjustable. There are two adjustment levers on each section of the split bench seats to adjust the seat forward or rearward. Lift up either lever and slide the seat forward or rearward.
Page 16 Folding or Reclining the Seatbacks CAUTION: If the seatback isn’t locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked.
Page 17: Removing The Split Bench Seat
To return the seatback to an upright position, pull on the 4. If the seat is in the second row, lift one of the nylon strap or lift the recliner lever without putting any adjustment levers and slide the seat fully rearward. pressure on the seatback.
Page 18: Replacing The Split Bench Seats
Replacing the Split Bench Seats CAUTION: If the seatback isn’t locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked.
Page 19 The seat must be placed in the proper location for the legs to attach correctly. CAUTION: Make sure the seat is in the full rear position before beginning this procedure. A safety belt that is improperly routed, not properly attached, or twisted won’t provide the protection needed in a crash.
Page 20 2. Make sure the bench seat is angled so that the front hooks clear the ﬂoor pins. If the front legs are not attached correctly, the rear legs will not attach to the rear set of ﬂoor pins. If the front latches are not attaching correctly, check that the seat is in the full rear position.
Page 21: Bucket Seats
Bucket Seats 5. Lift the seatback recliner lever or pull the nylon strap on the back of the seat and raise the seatback until it locks upright. If your vehicle has the bucket seats, the seatbacks can be folded down or reclined. The seats can also be 6.
Page 22: Adjusting The Bucket Seats
Adjusting the Bucket Seats The other lever is located on the rear of the There are two adjustment levers on each seat to adjust bucket seat. the seat forward or rearward. Lift up either lever and slide the seat forward or rearward.
Page 23 Folding or Reclining the Seatbacks CAUTION: If the seatback isn’t locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked.
Page 24: Removing The Bucket Seats
Removing the Bucket Seats To raise a seatback, pull the nylon strap or lift the recliner lever while raising the seatback until it locks Make sure the seatback is in the upright position. The upright. Push and pull on the seatback to check that it is head restraints should be fully down.
Page 25 You can also lift the lever on the side of the seat to 4. To unlatch the front latches, with the seat folded release the rear latches from the ﬂoor pins. forward, squeeze the angled bar toward the straight crossbar. Do not let go of the strap or lever until the seat is folded all the way forward.
Page 26: Replacing The Bucket Seats
Replacing the Bucket Seats CAUTION: CAUTION: A safety belt that is improperly routed, not properly attached, or twisted won’t provide the If the seatback isn’t locked, it could move protection needed in a crash. The person forward in a sudden stop or crash. That could wearing the belt could be seriously injured.
Page 27 Make sure the seats are in the full rear position before beginning this procedure. 1. With the seat folded, squeeze the angled bar toward the straight crossbar while placing the front hooks of the bucket seat onto the front two ﬂoor pins.
Page 28: Captain Chairs
Captain Chairs Folding or Reclining the Seatbacks If your vehicle has captain’s chairs, the chairs and seatbacks can be adjusted forward or rearward. CAUTION: Adjusting the Captain’s Chairs (Second Row) If the seatback isn’t locked, it could move forward in a sudden stop or crash. That could The second row captain’s chairs can be adjusted cause injury to the person sitting there.
Page 29: Removing The Captain's Chairs
Removing the Captain’s Chairs To recline the seatback, lift up on the recliner lever, located on the outboard side of the seat. Use the recliner 1. Pull the nylon strap behind the chair to release the lever to move the seatback to the desired position. rear hooks from the ﬂoor pins.
Page 30: Replacing The Captain's Chairs
Replacing the Captain’s Chairs CAUTION: If the seatback isn’t locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked.
Page 31 Make sure the seatbacks are in the upright position, the seat belts are on the correct side of the chairs and CAUTION: the second row captain’s chairs are in the full rear position before beginning this procedure. A safety belt that is improperly routed, not properly attached, or twisted won’t provide the protection needed in a crash.
Page 32: Stowable Seat
Stowable Seat Your vehicle may have a stowable seat. The stowable seat is a full bench seat and comes with the convenience center. See Convenience Center on page 2-58 for more information. The stowable seat can be removed and replaced, or with the seatback folded, it can lie ﬂush with the convenience center.
Page 33: Removing The Stowable Seat
Removing the Stowable Seat To fold down the seatback, pull up on the lever located 1. Remove the convenience center, if it is in the on the back of the seat vehicle. See Convenience Center on page 2-58 and push the seatback for more information.
Page 34: Replacing The Stowable Seat
Replacing the Stowable Seat 5. While holding onto the crossbar at the bottom of the seat, remove the seat by rocking it slightly toward the rear of the vehicle and then pulling it out. This should be done in one motion. CAUTION: Notice: If you use the release handles to remove the seat, the handles could break, and the repairs...
Page 35 The seat must be placed in the proper location for the legs to attach correctly. CAUTION: Make sure the seat is in its upright position before beginning this procedure. A safety belt that is improperly routed, not 1. Place the front hooks of the seat onto the front properly attached, or twisted won’t provide the ﬂoor pins in the third row.
Page 36: Safety Belts
Safety Belts CAUTION: Safety Belts: They Are for Everyone It is extremely dangerous to ride in a cargo This part of the manual tells you how to use safety area, inside or outside of a vehicle. In a belts properly. It tells you some things you should not collision, people riding in these areas are more do with safety belts.
Page 37: Why Safety Belts Work
Why Safety Belts Work Your vehicle has a light that comes on as a When you ride in or on anything, you go as fast as reminder to buckle up. See it goes. Safety Belt Reminder Light on page 3-40 . In most states and in all Canadian provinces, the law says to wear safety belts.
Page 38 Put someone on it. Get it up to speed. Then stop the vehicle. The rider doesn’t stop. 1-32...
Page 39 The person keeps going until stopped by something. In or the instrument panel... a real vehicle, it could be the windshield... 1-33...
Page 40: Questions And Answers About Safety Belts
Questions and Answers About Safety Belts Won’t I be trapped in the vehicle after an accident if I’m wearing a safety belt? You could be – whether you’re wearing a safety belt or not. But you can unbuckle a safety belt, even if you’re upside down.
Page 41: How To Wear Safety Belts Properly
How to Wear Safety Belts Properly If I’m a good driver, and I never drive far from home, why should I wear safety belts? This part is only for people of adult size. You may be an excellent driver, but if you’re in an Be aware that there are special things to know about accident –...
Page 42: Driver Position
Driver Position This part describes the driver’s restraint system. Lap-Shoulder Belt The driver has a lap-shoulder belt. Here’s how to wear it properly. 1. Close and lock the door. 2. Adjust the seat so you can sit up straight. To see how, see “Seats”...
Page 43 4. Push the latch plate into the buckle until it clicks. Pull up on the latch plate to make sure it is secure. If the belt isn’t long enough, see Safety Belt Extender on page 1-54 . Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to.
Page 44: Shoulder Belt Height Adjuster
Shoulder Belt Height Adjuster To move it down, push down on the button and move the height adjuster to the desired position. You can Before you begin to drive, move the shoulder belt move the adjuster up just by pushing up on the shoulder adjuster to the height that is right for you.
Page 45 What’s wrong with this? CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should ﬁt against your body. The shoulder belt is too loose. It won’t give nearly as much protection this way.
Page 46 What’s wrong with this? CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones.
Page 47 What’s wrong with this? CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied at the abdomen, not at the pelvic bones, and that could cause serious or fatal injuries.
Page 48 What’s wrong with this? CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury. Also, the belt would apply too much force to the ribs, which aren’t as strong as shoulder bones.
Page 49 What’s wrong with this? CAUTION: You can be seriously injured by a twisted belt. In a crash, you wouldn’t have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to ﬁx it.
Page 50: Safety Belt Use During Pregnancy
Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they don’t wear safety belts. To unlatch the belt, just push the button on the buckle. The belt should go back out of the way.
Page 51: Center Passenger Position
Center Passenger Position The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it’s more (Bucket Seat) likely that the fetus won’t be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly.
Page 52: Lap Belt
Lap Belt 2. Push the latch plate into the buckle until it clicks. If the belt stops before it reaches the buckle, let it go If your vehicle has bucket seats, someone can sit in the back all the way and start again. Pull up on the center position bucket seat.
Page 53: Bench Seat
Lap Belt Make sure the release button on the buckle is positioned so you would be able to unbuckle the If your vehicle has a third row rear bench seat, someone safety belt quickly if you ever had to. can sit in the center position. Center Passenger Position (Bench Seat) When you sit in the center position of the bench seat,...
Page 54: Rear Seat Passengers
Rear Seat Passengers It’s very important for rear seat passengers to buckle up! Accident statistics show that unbelted people in the rear seat are hurt more often in crashes than those who are wearing safety belts. Rear passengers who aren’t safety belted can be thrown out of the vehicle in a crash.
Page 55: Rear Seat Outside Passenger Positions
Rear Seat Outside Passenger Positions Lap-Shoulder Belt 1. Pick up the latch plate and pull the belt across you. Don’t let it get twisted. The positions next to the windows have lap-shoulder belts. Here’s how to wear one properly. The shoulder belt may lock if you pull the belt across you very quickly.
Page 56 Third Row Outside Passenger Position 3. To make the lap part tight, pull down on the buckle end of the belt as you pull up on the shoulder part. Pull up on the latch plate to make sure it is secure. When the shoulder belt is pulled out all the way, it will lock.
Page 57 CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should ﬁt against your body. The lap part of the belt should be worn low and snug on the hips, just touching the thighs.
Page 58: Rear Safety Belt Comfort Guides For Children And Small Adults
Rear Safety Belt Comfort Guides for Children and Small Adults Your vehicle may have rear shoulder belt comfort guides. This feature will provide added safety belt comfort for older children who have outgrown booster seats and for small adults. When installed on a shoulder belt, the comfort guide better positions the belt away from the neck and head.
Page 59 2. Place the guide over the belt and insert the two 3. Be sure that the belt is not twisted and it lies ﬂat. edges of the belt into the slots of the guide. The guide must be on top of the belt. 1-53...
Page 60: Safety Belt Pretensioners
Safety Belt Pretensioners Your vehicle has safety belt pretensioners. You’ll ﬁnd them on the buckle end of the safety belts for the driver and right front passenger. They help the safety belts reduce a person’s forward movement in a moderate to severe crash in which the front of the vehicle hits something.
Page 61: Child Restraints
Child Restraints What is the proper way to wear safety belts? If possible, an older child should wear a Older Children lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should ﬁt snugly below the hips, just touching the top of the thighs.
Page 62 What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt is very close to the child’s face or neck? Move the child toward the center of the vehicle, but be sure that the shoulder belt still is on the child’s shoulder, so that in a crash the child’s upper body would have the restraint that belts provide.
Page 63 CAUTION: Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide under the belt.
Page 64: Infants And Young Children
Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
Page 65 CAUTION: (Continued) CAUTION: it. For example, in a crash at only 25 mph Children who are up against, or very close to, (40 km/h), a 12-lb. (5.5 kg) baby will suddenly any air bag when it inﬂates can be seriously become a 240-lb.
Page 66 What are the different types of add-on child restraints? CAUTION: Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic Newborn infants need complete support, types. Selection of a particular restraint should take including support for the head and neck. This into consideration not only the child’s weight, is necessary because a newborn infant’s neck height and age but also whether or not the restraint...
Page 67: Child Restraint Systems
Child Restraint Systems CAUTION: The body structure of a young child is quite unlike that of an adult or older child, for whom the safety belts are designed. A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should.
Page 68 A rear-facing infant seat (B) provides restraint with the A forward-facing child seat (C-E) provides restraint for seating surface against the back of the infant. The the child’s body with the harness and also sometimes harness system holds the infant in place and, in a crash, with surfaces such as T-shaped or shelf-like shields.
Page 69 How do child restraints work? A child restraint system is any device designed for use in a motor vehicle to restrain, seat, or position children. A built-in child restraint system is a permanent part of the motor vehicle. An add-on child restraint system is a portable one, which is purchased by the vehicle’s owner.
Page 70 When choosing a child restraint, be sure the child When securing an aftermarket child seat in a restraint is designed to be used in a vehicle. If it is, it bucket seat, I am unable to get the seat will have a label saying that it meets federal fastened in snugly enough.
Page 71: Where To Put The Restraint
Where to Put the Restraint CAUTION: (Continued) Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. You may secure a forward-facing child General Motors, therefore, recommends that child restraints be secured in a rear seat, including an infant restraint in the right front seat, but before you riding in a rear-facing infant seat, a child riding in a do, always move the front passenger seat as...
Page 72: Top Strap
Top Strap Some child restraints have a top strap, or “top tether”. It can help restrain the child restraint during a collision. For it to work, a top strap must be properly anchored to the vehicle. Some top strap-equipped child restraints are designed for use with or without the top strap being anchored.
Page 73 Top Strap Anchor Location In Canada, the law requires that forward-facing child restraints have a top strap, and that the strap be anchored. In the United States, some child restraints also have a top strap. If your child restraint has a top strap, it should be anchored.
Page 74 Third Row Third Row (Stowable Seat) An anchor bar for a top strap is located at the rear of The anchor bar for the stowable bench seat is located the seat cushion for each second and third row outboard on the passenger’s side of the crossbar. Use the center seating position, and for the center position of the seating position to use the anchor bar properly.
Page 75 Lower Anchorages and Top Tethers In order to use the system, you need either a forward-facing child restraint that has attaching points for Children (LATCH System) (B) at its base and a top tether anchor (C), or a rear-facing child restraint that has attaching points (B), Your vehicle has the LATCH system.
Page 76 CAUTION: If a LATCH-type child restraint isn’t attached to its anchorage points, the restraint won’t be able to protect the child correctly. In a crash, the child could be seriously injured or killed. Make sure that a LATCH-type child restraint is properly installed using the anchorage points, or use the vehicle’s safety belts to secure the restraint.
Page 77: Securing A Child Restraint Designed For The Latch System
Securing a Child Restraint Designed Securing a Child Restraint in a Rear for the LATCH System Outside Seat Position 1. Find the anchors for the seating position you want to use, where the bottom of the seatback meets the back of the seat cushion. 2.
Page 78 For vehicles with a full bench seat in the third row, there is no top strap anchor in the driver’s side position. Do not secure a child seat in this position if a national or local law requires that the top strap be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored.
Page 79 3. Buckle the belt. Make sure the release button is 4. Pull the rest of the shoulder belt all the way out of positioned so you would be able to unbuckle the the retractor to set the lock. safety belt quickly if you ever had to. 1-73...
Page 80 5. To tighten the belt, feed the shoulder belt back into the retractor while you push down on the child restraint. If you’re using a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 81 Securing a Child Restraint in a Center Seat Position (Third Row Bench Seat) 1. Make the belt as long as possible by tilting the latch plate and pulling it along the belt. 2. Put the restraint on the seat. You’ll be using the lap belt. Be sure to follow the instructions that came with the child restraint.
Page 82 4. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 5. To tighten the belt, pull its free end while you push down on the child restraint. If you’re using a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 83 Securing a Child Restraint in a 1. Put the restraint on the seat. Center Seat Position (Bucket Seat) You’ll be using the lap belt. See Top Strap on page 1-66 2. Pull the lap belt all the way out without stopping. if the child restraint has one.
Page 84 4. Buckle the belt. Make sure the release button is 5. To tighten the belt, feed it back into the retractor positioned so you would be able to unbuckle the while you push down on the child restraint. If safety belt quickly if you ever had to. you’re using a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 85: Securing A Child Restraint In The Right Front Seat Position
Securing a Child Restraint in the Your vehicle has a front passenger air bag. Never put a rear-facing child restraint in this seat. Here’s why: Right Front Seat Position CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the front passenger’s air bag inﬂates.
Page 86 You’ll be using the lap-shoulder belt. See Top Strap on page 1-66 if the child restraint has one. Be sure to follow the instructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say.
Page 87 5. Pull the rest of the lap belt all the way out of the 6. To tighten the belt, feed the shoulder belt back into retractor to set the lock. the retractor while you push down on the child restraint. You may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 88: Built-In Child Restraint
Built-In Child Restraint 60/40 Bench Seat Bucket Seat 1-82...
Page 89 If your vehicle has this option in a bucket seat, each What if the top of my child’s shoulders is above bucket seat that has the built-in child restraint ﬁts in only the shoulder belt slots for the ﬁve-point child one location in your vehicle.
Page 90 Securing a Child in the Built-In Child Restraint 2. Rotate the head restraint rearward until it touches the top of the seatback. Make sure there is no gap between the lower edge of the head restraint and the top of the seatback. 1.
Page 91 You’ll be using the child restraint’s harness (A) 3. Lower the child restraint cushion. to secure your child. Don’t use the vehicle’s safety belts. 1-85...
Page 92 CAUTION: Using the vehicle’s regular safety belts on a child seated on the child restraint cushion can cause serious injury to the child in a sudden stop or crash. If a child is the proper size for the built-in child restraint, secure the child using the child restraint’s harness.
Page 93 8. Place the other side of the harness over the child’s shoulder. 9. Push the latch plate into the buckle until it clicks. 6. Select only one side of the harness. Place the harness over the child’s shoulder. 7. Push the latch plate (B) into the buckle until it clicks.
Page 94 CAUTION: An unfastened shoulder harness clip won’t help keep the harness in place on the child’s shoulders. If the harness isn’t on the child’s shoulders, it won’t be able to restrain the child’s upper body in a sudden stop or crash. The child could be seriously injured.
Page 95 12. Pull the shoulder harness adjustment strap (C) 13. Adjust the position of the harness on the child’s ﬁrmly until the harness is snugly adjusted around shoulder by moving the clip along the harness the child. You should not be able to put more than until it is level with the child’s armpits.
Page 96 Removing the Child from the Built-In Child Restraint 2. Unlatch the harness by pushing the button on the buckle. 3. Move one side of the harness off the child’s 1. Unfasten the shoulder harness clip. shoulder. 4. Move the other side of the harness off the child’s shoulder.
Page 97: Storing The Built-In Child Restraint
Storing the Built-In Child Restraint Always properly store the built-in child restraint before using the vehicle’s lap-shoulder belt. 2. Fold the child restraint cushion and leg rest up into the seatback. 3. Press the child restraint cushion ﬁrmly into the seatback.
Page 98 4. Then press the leg rest ﬁrmly into the seatback, 5. Rotate the head restraint forward and push it all the and secure it by pressing the upper corners way down. against the fastener strips on the seatback. Just like the other restraint systems in your vehicle, your built-in child restraint needs to be periodically checked and may need to have parts replaced after a crash.
Page 99: Air Bag Systems
Air Bag Systems This part explains the frontal and side impact air bag systems. Your vehicle has air bags – a frontal air bag for the driver and another frontal air bag for the right front passenger. Your vehicle may also have a side impact air bag.
Page 100 Here are the most important things to know about the air bag systems: CAUTION: (Continued) CAUTION: The side impact air bags for the driver and right front passenger are designed to inﬂate only in moderate to severe crashes where You can be severely injured or killed in a crash something hits the side of your vehicle.
Page 101 CAUTION: (Continued) CAUTION: not for young children and infants. Neither the Both frontal and side impact air bags inﬂate vehicle’s safety belt system nor its air bag with great force, faster than the blink of an system is designed for them. Young children eye.
Page 102: Where Are The Air Bags
Where Are the Air Bags? The right front passenger’s frontal air bag is in the instrument panel on the passenger’s side. The driver’s frontal air bag is in the middle of the If your vehicle has one, the driver’s side impact air steering wheel.
Page 103 CAUTION: If something is between an occupant and an air bag, the bag might not inﬂate properly or it might force the object into that person causing severe injury or even death. The path of an inﬂating air bag must be kept clear. Don’t put anything between an occupant and an air bag, and don’t attach or put anything on the steering wheel hub or on or near any other air...
Page 104: When Should An Air Bag Inﬂate
When Should an Air Bag Inﬂate? Your vehicle may or may not have a side impact air bag. See Air Bag Systems on page 1-93 . Side impact air bags are designed to inﬂate in moderate to severe The driver’s and right front passenger’s frontal air bags side crashes.
Page 105: What Makes An Air Bag Inﬂate
What Makes an Air Bag Inﬂate? How Does an Air Bag Restrain? In an impact of sufficient severity, the air bag sensing In moderate to severe frontal or near frontal collisions, system detects that the vehicle is in a crash. For even belted occupants can contact the steering wheel or both frontal and side impact air bags, the sensing the instrument panel.
Page 106: What Will You See After An Air
What Will You See After an Air CAUTION: Bag Inﬂates? After the air bag inﬂates, it quickly deﬂates, so quickly When an air bag inﬂates, there is dust in the that some people may not even realize the air bag air.
Page 107 • In many crashes severe enough to inﬂate an air bag, Your vehicle is equipped with two electronic frontal windshields are broken by vehicle deformation. sensors, which help the sensing system distinguish Additional windshield breakage may also occur from the between a moderate frontal impact and a more right front passenger air bag.
Page 108: Servicing Your Air Bag-Equipped Vehicle
Notice: If you damage the covering for the driver’s Servicing Your Air Bag-Equipped or the right front passenger’s air bag, or the air Vehicle bag covering on the driver’s and right front passenger’s seatback, the bag may not work Air bags affect how your vehicle should be serviced. properly.
Page 109: Restraint System Check
Restraint System Check Torn or frayed safety belts may not protect you in a crash. They can rip apart under impact forces. If a belt is torn or frayed, get a new one right away. Checking Your Restraint Systems If your vehicle has the built-in child restraint, torn or frayed harness straps can rip apart under impact forces Now and then, make sure the safety belt reminder light just like torn or frayed safety belts can.
Page 110: Replacing Restraint System Parts
Replacing Restraint System Parts If you’ve had a crash, do you need new safety belts or built-in child restraint parts or LATCH system parts? After a Crash After a very minor collision, nothing may be necessary. But if the safety belts or built-in child restraint harness straps were stretched, as they would be if worn during a CAUTION: more severe crash, then you need new parts.
Page 111: Features And Controls
Section 2 Features and Controls Keys ...............2-3 Ignition Positions ..........2-31 Remote Keyless Entry System ......2-5 Starting Your Engine ........2-32 Remote Keyless Entry System Operation ...2-6 Engine Coolant Heater ........2-33 Automatic Transaxle Operation .......2-34 Doors and Locks ..........2-9 Parking Brake ..........2-38 Door Locks ............2-9 Shifting Into Park (P) ........2-39 Power Door Locks ........2-11...
Page 112 Section 2 Features and Controls Rear Storage Area ........2-57 Last Door Locking and Lockout Deterrent ..2-64 Convenience Net ..........2-57 Remote Driver Unlock Control ......2-65 Convenience Center ........2-58 Remote Lock and Unlock Conﬁrmation .....2-66 Content Theft-Deterrent System ......2-67 Vehicle Personalization ........2-61 Arming and Disarming the Content Entering Programming Mode ......2-62 Theft-Deterrent System .......2-68...
Page 113: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. A child or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. Do not leave the keys in a vehicle with children.
Page 114 Be sure you have spare keys. If you ever do get locked out of your vehicle, call the Chevrolet Roadside Assistance center. See Roadside Assistance Program on page 7-6 . ®...
Page 115: Remote Keyless Entry System
Remote Keyless Entry System At times you may notice a decrease in range. This is normal for any remote keyless entry system. If the transmitter does not work or if you have to stand closer If equipped, the keyless entry system operates on a to your vehicle for the transmitter to work, try this: radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada.
Page 116: Remote Keyless Entry System Operation
Remote Keyless Entry System With the content theft-deterrent system, the UNLOCK button on the remote keyless entry transmitter will Operation disarm the system. See Content Theft-Deterrent on page 2-27 for more details. You can lock and unlock When you use your remote keyless entry transmitter to your doors and the liftgate unlock your vehicle or to operate the power sliding from about 3 feet (1 m)
Page 117: Remote Alarm
Remote Alarm You can operate the power sliding door(s) with the remote keyless entry transmitter only when the power When you press the horn button on the remote keyless sliding door override switch(es) on the overhead console entry transmitter, the parking lamps will ﬂash and the is turned off.
Page 118: Battery Replacement
Battery Replacement Under normal use, the battery in your remote keyless entry transmitter should last about three years. You can tell the battery is weak if the transmitter won’t work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it’s probably time to change the battery.
Page 119: Doors And Locks
Doors and Locks CAUTION: (Continued) Door Locks • Young children who get into unlocked vehicles may be unable to get out. A child can be overcome by extreme heat and can CAUTION: suffer permanent injuries or even death from heat stroke. Always lock your vehicle whenever you leave it.
Page 120 To unlock the driver’s door from the outside with the key, insert the key and turn it toward the front of the vehicle. If your vehicle has power door locks, you can unlock all of the doors and the liftgate by inserting the key, turning it toward the front of the vehicle and holding it there for one second.
Page 121: Power Door Locks
Power Door Locks You can lock all doors and the liftgate from the inside by pressing the rear of the power lock switch on either front door. With the content theft-deterrent system, the power door lock switch may cause the system to arm.
Page 122: Last Door Closed Locking
Last Door Closed Locking Programmable Automatic Door Locks The last door closed locking feature will delay the power locking of the doors and liftgate for up to ﬁve seconds All of the doors will lock automatically when you move after exiting the vehicle, when the power door lock your shift lever out of PARK (P).
Page 123: Lockout Protection
Sliding Door Delayed Locking Leaving Your Vehicle If either sliding door is open when you use the power If you are leaving the vehicle, take your keys, open your door locks to lock the vehicle, the sliding door that door and set the locks from the inside. Then get out is open will not lock.
Page 124: Sliding Door Lock
Sliding Door Lock CAUTION: If your vehicle is facing downward on a steep grade (15 percent or more), the door may not stay open and could slam shut, possibly injuring someone. To make sure the door does not slam shut be sure to hold it open until everyone is clear of the door, and only then allow it to slowly close.
Page 125: Sliding Door Security Lock
Sliding Door Security Lock Your vehicle is equipped with a sliding door security lock that helps prevent young children or other passengers from opening the sliding door(s) using the inside door handle. To use one of these locks, do the following: 1.
Page 126 Canceling the Sliding Door If your vehicle has the power sliding door(s), you can override the security lock by pressing either power door Security Lock lock switch while the power sliding door override switch(es) is turned off. If the power sliding door override 1.
Page 127: Power Sliding Door (Psd)
Power Sliding Door (PSD) If your vehicle has this feature, you can open and close the sliding door(s) using the switches inside of your vehicle. You can also operate the power sliding door(s) with your remote keyless entry transmitter. See Remote Keyless Entry System on page 2-5 .
Page 128 Notice: If you leave the power sliding door on If you have the dual sliding doors, your vehicle has when you go through an automatic car wash, the these switches. The door may accidentally open. Be sure the power left switch is for the driver’s sliding door is turned off when going through a side power sliding door car wash.
Page 129 If the power sliding door(s) is open or in the process of closing when you shift out of PARK (P), a buzzer will sound. This is a warning that the sliding door(s) is not completely closed. If the power to the sliding door(s) is turned off, the buzzer will not sound indicating the door(s) is not completely closed.
Page 130 The driver’s side sliding door is designed to open only a little if the fuel door is open. If this ever happens, don’t try to force the sliding door. When the fuel ﬁller door is closed, the driver’s side sliding door can be opened normally.
Page 131: Resetting The Power Sliding Door
Resetting the Power Sliding Door CAUTION: The power sliding door may operate incorrectly or not at all because of the following conditions: • A low voltage or dead battery, If your vehicle is facing downward on a steep grade (15 percent or more), the door may not •...
Page 132: Liftgate
Liftgate 3. If the power sliding door override is on, press the textured end of the power sliding door override switch to turn it off. To unlock the liftgate from the outside, turn the key in the cylinder clockwise or use the remote keyless 4.
Page 133 CAUTION: It can be dangerous to drive with the liftgate open because carbon monoxide (CO) gas can come into your vehicle. You can’t see or smell CO. It can cause unconsciousness and even death. If you must drive with the liftgate open or if electrical wiring or other cable connections must pass through the seal between the body and the liftgate:...
Page 134: Windows
Windows CAUTION: Leaving children in a vehicle with the windows closed is dangerous. A child can be overcome by the extreme heat and can suffer permanent injuries or even death from heat stroke. Never leave a child alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 135: Power Windows
Power Windows Express-Down Window To activate the express-down feature, push the AUTO switch all the way down to the second position, then release it. The window will lower completely. To stop the window from lowering all the way, pull up on the front of the switch.
Page 136: Power Rear Quarter Windows
Power Rear Quarter Windows Press the part of the switch with the symbol to close both windows. The windows can be closed fully or partway depending on how long the switch is pressed. Your vehicle may have power rear quarter windows. The ignition must be in RUN, ACCESSORY or This switch, located in the Retained Accessory Power (RAP) must be active, to...
Page 137: Theft-Deterrent Systems
Theft-Deterrent Systems While armed, the doors will not unlock with the power door lock switch. Vehicle theft is big business, especially in some cities. Once armed, the alarm will go off if someone tries to Although your vehicle has a number of theft-deterrent enter the vehicle (without using the remote keyless entry features, we know that nothing we put on it can make it transmitter or a key) or turns the ignition to ON.
Page 138: Disarming With Your Key
Arming with the Remote Keyless Entry Arming Conﬁrmation Transmitter If remote unlock conﬁrmation is on, your parking lamps will ﬂash brieﬂy to let you know when your alarm Your alarm system will arm when you use your remote system has disarmed. If you would not like the parking keyless entry transmitter to lock the doors, if the key lamps to ﬂash, see Vehicle Personalization on is not in the ignition.
Page 139: Pass-Key ® Iii
® ® PASS-Key PASS-Key III Operation ® Your PASS-Key III system operates on a radio Your vehicle is equipped frequency subject to Federal Communications ® with the PASS-Key Commission (FCC) Rules and with Industry Canada. (Personalized Automotive This device complies with Part 15 of the FCC Rules. Security System) Operation is subject to the following two conditions: theft-deterrent system.
Page 140 If the engine still does not start, and the key appears to To program the new key, do the following: be undamaged, try another ignition key. At this time, 1. Verify the new key has PK3 stamped on it. you may also want to check the instrument panel PASS 2.
Page 141: Starting And Operating Your Vehicle
Starting and Operating Your Ignition Positions Vehicle With the key in the ignition, you can turn it to ﬁve different positions. New Vehicle Break-In Notice: Your vehicle does not need an elaborate “break-in.” But it will perform better in the long run if you follow these guidelines: •...
Page 142: Starting Your Engine
B (LOCK): This is the only position from which you can If the engine is not running, ACCESSORY and RUN are remove the key. This position locks your ignition, positions that allow you to operate your electrical steering wheel and transaxle. accessories, such as the radio.
Page 143: Engine Coolant Heater
Notice: Holding your key in START for longer than Engine Coolant Heater 15 seconds at a time will cause your battery to be drained much sooner. And the excessive heat can damage your starter motor. Wait about 15 seconds between each try to help avoid draining your battery or damaging your starter.
Page 144: To Use The Engine Coolant Heater
To Use the Engine Coolant Heater How long should you keep the coolant heater plugged in? The answer depends on the outside temperature, the 1. Turn off the engine. kind of oil you have, and some other things. Instead of trying to list everything here, we ask that you contact 2.
Page 145 PARK (P): This gear position locks your front wheels. It’s the best position to use when you start your CAUTION: engine because your vehicle can’t move easily. Ensure the shift lever is fully in PARK (P) before starting It is dangerous to get out of your vehicle if the the engine.
Page 146 Notice: Shifting our of PARK (P) or NEUTRAL (N) REVERSE (R): Use this gear to back up. with the engine racing may damage the transaxle. Notice: Shifting to REVERSE (R) while your vehicle The repairs would not be covered by your warranty. is moving forward could damage the transaxle.
Page 147: Warm-Up Shift
Warm-Up Shift Notice: Driving in SECOND (2) for more than 25 miles (40 km) or at speeds over 55 mph (90 km/h) Your vehicle has a computer controlled transaxle may damage the transaxle. Also, shifting into designed to warm up the engine faster when the outside SECOND (2) at speeds above 65 mph (105 km/h) can temperature is 35°F (2°C) or colder.
Page 148: Parking Brake
Parking Brake If the ignition is on, the brake system warning light will come on. See Brake System Warning Light on page 3-41 . The parking brake is To release the parking brake, hold the regular brake located on the driver’s side pedal down with your right foot while you push down on under the instrument the parking brake pedal with your left foot.
Page 149: Shifting Into Park (P)
Shifting Into Park (P) 2. Move the shift lever into PARK (P) like this: CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll.
Page 150: Leaving Your Vehicle With The Engine Running
Leaving Your Vehicle With the Engine Running CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch ﬁre.
Page 151: Torque Lock
Torque Lock Shifting Out of Park (P) If you are parking on a hill and you don’t shift your Your vehicle has an automatic transaxle shift lock transaxle into PARK (P) properly, the weight of control system. You have to fully apply your regular the vehicle may put too much force on the parking pawl brakes before you can shift from PARK (P), when in the transaxle.
Page 152: Parking Over Things That Burn
Parking Over Things That Burn Engine Exhaust CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you can not see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: • Your exhaust system sounds strange or different.
Page 153: Running Your Engine While You Are Parked
Running Your Engine While You CAUTION: Are Parked It is better not to park with the engine running. But if It can be dangerous to get out of your vehicle you ever have to, here are some things to know. if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set.
Page 154: Mirrors
Mirrors Turn the control counterclockwise to select the driver’s side rearview mirror, or clockwise to select the passenger’s side rearview mirror. Manual Rearview Mirror Then use the control to adjust each mirror so that you can see a little of the side of your vehicle and the To reduce glare from lights behind you, pull the lever area beside and behind your vehicle when you are toward you (to the night position).
Page 155: Outside Convex Mirror
® Outside Convex Mirror OnStar System Your passenger’s side mirror is convex. A convex mirror’s surface is curved so you can see more from the driver’s seat. CAUTION: A convex mirror can make things (like other ® OnStar uses global positioning system (GPS) satellite vehicles) look farther away than they really are.
Page 156: Onstar Services
® OnStar Services Luxury and Leisure Plan • All Directions and Connections Plan services One of the following plans is normally included for a speciﬁc duration with each vehicle equipped with • Personal Concierge ® ® OnStar . You can upgrade or extend your OnStar ®...
Page 157: Homelink Transmitter
® ® HomeLink Transmitter If your vehicle is equipped with the HomeLink transmitter, it complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 158: Programming The Homelink
® Programming the HomeLink It is recommended that a new battery be installed in your hand-held transmitter for quicker and more Transmitter accurate transmission of the radio frequency. Your vehicle’s engine should be turned off while ® Do not use the HomeLink Transmitter with any garage programming the transmitter.
Page 159 ® 5. Press and hold the newly-trained HomeLink button 7. Firmly press and release the “Learn” or “Smart” and observe the indicator light. button. The name and color of the button may vary by manufacturer. If the indicator light stays on constantly, programming is complete and your device should You will have 30 seconds to start Step 8.
Page 160: Using Homelink
® Gate Operator and Canadian Using HomeLink Programming ® Press and hold the appropriate HomeLink button for at least half of a second. The indicator light will come Canadian radio-frequency laws require transmitter on while the signal is being transmitted. signals to “time out”...
Page 161: Storage Areas
® Reprogramming a Single HomeLink Storage Areas Button Your vehicle’s large carrying capacity can store many items. If you have the extended wheelbase version, you ® ® To program a device to HomeLink using a HomeLink can carry things as large as a 4’ x 8’ piece of plywood. button previously trained, follow these steps: You can also use the ﬂoor pins that are used to ®...
Page 162: Compact Overhead Console
Compact Overhead Console Overhead Console The front overhead console includes two reading lamps, a storage compartment and a switchbank. Your vehicle may have this feature. The front overhead console has reading lamps, a switchbank, storage compartments, a garage door opener compartment, ®...
Page 163: Garage Door Opener Compartment
® If your vehicle has the HomeLink transmitter buttons, they will take the place of the garage door opener compartment. The garage door opener compartment is explained next. For information on the other features listed, see each of them in the Index. Garage Door Opener Compartment You can store your garage door opener in the rear compartment of your overhead console, and operate it...
Page 164: Front Seat Storage Net
Front Seat Storage Net 5. Add one peg at a time until your garage door opener operates with the compartment door closed when you press on it. There may be a storage net that stretches between the front seats. Pull the hooks towards the passenger’s seat and insert them into the holes.
Page 165: Luggage Carrier
Luggage Carrier CAUTION: If you try to carry something on top of your vehicle that is longer or wider than the luggage carrier — like paneling, plywood, a mattress and so forth — the wind can catch it as you drive along.
Page 166 Don’t exceed the maximum vehicle capacity when loading your vehicle. For more information on vehicle capacity and loading, see Loading Your Vehicle on page 4-34 . To prevent damage or loss of cargo as you’re driving, check now and then to make sure the luggage carrier and cargo are still securely fastened.
Page 167: Rear Storage Area
Convenience Net Use the tie-down loops on the slider to help secure large loads. Your vehicle may have a convenience net. The convenience net is designed to help keep small loads, like grocery bags, from falling over. Install the convenience net at the rear of your vehicle, inside the liftgate.
Page 168: Convenience Center
Convenience Center CAUTION: If any removable convenience item is not secured properly, it can move around in a collision or sudden stop. People in the vehicle could be injured. Be sure to secure any such item properly. Your vehicle may have a convenience center. It comes with the stowable seat.
Page 169: Removing The Convenience Center
Removing the Convenience Center 1. Make sure that all items are off of the convenience center and that it is empty. 2. Turn the hand knob counterclockwise until the knob is loose. 3. Lift up on the hand knob, then grip the convenience center to lift it up.
Page 170 The tray sill can be folded down onto the stowable seat The convenience center and the stowable seat both to close the space between the two while the stowable have a maximum weight capacity of 400 lbs. (181.6 kg). seat is folded down. To do this, ﬂip the sill plate up and Notice: Loading objects that weigh over 400 lbs over toward the stowable seat.
Page 171: Vehicle Personalization
Vehicle Personalization Your vehicle’s locks and lighting systems can be programmed with several different features. The features you can program depend on the options that came with your vehicle. The following chart shows the features that can be programmed. To determine which features your vehicle is equipped with, follow the steps listed for entering the programming mode.
Page 172: Entering Programming Mode
Entering Programming Mode Delayed Illumination and Exit Lighting To program features, your vehicle must be in the programming mode. Follow these steps: This feature allows you to customize the interior lamps 1. The content theft-deterrent system must be when entering and exiting the vehicle. disarmed.
Page 173: Automatic Door Locks
Automatic Door Locks Your vehicle was originally programmed to Mode 4. The mode may have been changed since then. To This feature allows you to customize the automatic determine the current mode, or to change the mode, do locking and unlocking of the doors when using the the following: shift lever.
Page 174: Last Door Locking And Lockout Deterrent
Last Door Locking and Lockout Your vehicle was originally programmed to Mode 3. The mode may have been changed since then. To Deterrent determine the current mode, or to change the mode, do the following: This feature allows you to customize the automatic 1.
Page 175: Remote Driver Unlock Control
Remote Driver Unlock Control Your vehicle was originally programmed to Mode 4. The mode may have been changed since then. To determine the current mode, or to change the mode, do This feature allows you to customize the UNLOCK the following: button on the remote keyless entry transmitter.
Page 176: Remote Lock And Unlock Conﬁrmation
Programmable Modes 3. Count the number of chimes you hear. The number of chimes indicates the vehicle’s current programmed mode. (If you do not wish to change Mode 1: Both Features Off (Remote lock and unlock the current mode, you can either exit the conﬁrmation are disabled.) programming mode by following the instructions Mode 2: Exterior Lamps Flash Only...
Page 177: Content Theft-Deterrent System
Mode 4: Exterior Lamps Flash and Horn Sounds (on 4. Press LOCK to change the current mode. second LOCK press) 5. Press LOCK until you hear the number of chimes corresponding to the mode selection you want. • When you use the remote keyless entry transmitter The mode you selected is now set.
Page 178: Arming And Disarming The Content
Arming and Disarming the Content 3. Count the number of chimes you hear. The number of chimes indicates the vehicle’s current Theft-Deterrent System programmed mode. (If you do not wish to change the current mode, you can either exit the To arm or disarm the content theft-deterrent system, the programming mode by following the instructions system must be turned on by using Modes 1, 2 or 4...
Page 179 • Mode 2: Remote Keyless Entry Transmitter The system will arm when you lock the doors with Arm/Disarm Only your key or remote keyless entry transmitter and the key is removed from the ignition. • The system will arm when you lock the doors with your remote keyless entry transmitter.
Page 180: Exiting Programming Mode
Exiting Programming Mode 4. Count the number of chimes you hear. The number of chimes indicates the vehicle’s current programmed mode. (If you do not wish to change To exit programming mode, turn the key from the current mode, you can either exit the ACCESSORY to OFF and put the BCM PRGRM fuse programming mode by following the instructions back into the instrument panel fuse block.
Page 181 Section 3 Instrument Panel Instrument Panel Overview .......3-4 Tachometer ..........3-39 Hazard Warning Flashers ........3-6 Safety Belt Reminder Light ......3-40 Other Warning Devices ........3-6 Air Bag Readiness Light ........3-40 Horn .............3-7 Brake System Warning Light ......3-41 Tilt Wheel .............3-7 Anti-Lock Brake System Warning Light .....3-42 Turn Signal/Multifunction Lever ......3-7 Traction Control System (TCS) Exterior Lamps ..........3-15...
Page 182 Section 3 Instrument Panel Driver Information Center (DIC) .......3-58 Rear Seat Audio (RSA) (With Entertainment System) ......3-101 Audio System(s) ..........3-61 Theft-Deterrent Feature (Non-RDS Radios) ..3-103 Setting the Time for Radios without Radio Theft-Deterrent Feature (RDS Radios) ....3-103 Data Systems (RDS) ........3-61 DVD Distortion ..........3-103 Setting the Time for Radios with Radio Understanding Radio Reception ....3-104...
Page 183 NOTES...
Page 184: Instrument Panel Overview
Instrument Panel Overview...
Page 185 The main components of the instrument panel are the following: A. Side Outlets. See Outlet Adjustment on page 3-28 . L. Ignition Switch. See Ignition Positions on page 2-31 . B. Front Outlets. See Outlet Adjustment on page 3-28 . M.
Page 186: Hazard Warning Flashers
Hazard Warning Flashers Your hazard warning ﬂashers button is located on top of the steering column. Your hazard warning ﬂashers work no matter what position your key is in, and even if the key isn’t in. Press the button to make the front and rear turn signal lamps ﬂash on and off.
Page 187: Horn
Horn Turn Signal/Multifunction Lever You can sound the horn by pressing the horn symbols on your steering wheel. Tilt Wheel A tilt wheel allows you to adjust the steering wheel before you drive. You can raise it to the highest level to give your legs more room when you exit and enter the vehicle.
Page 188: Turn And Lane-Change Signals
Turn and Lane-Change Signals If you have a trailer towing option with added wiring for the trailer lamps, the signal indicator will ﬂash at a The turn signal has two upward (for right) and two normal rate even if a turn signal bulb is burned downward (for left) positions.
Page 189: Windshield Wipers
Flash-to-Pass HIGH: Turn the band to HIGH, for steady wiping at high speed. When the headlamps are off, pull the lever toward you DELAY: Turn the band away from you to one of the to momentarily switch on the high beams (to signal ﬁve sensitivity settings between OFF and LOW, to that you are going to pass).
Page 190: Windshield Washer
Windshield Washer Rear Window Washer/Wiper Your vehicle may have a (Windshield Washer): Press and hold the rear window wiper. If it windshield washer paddle with this symbol on it to wash does, the rear window your windshield. The washers and wipers will operate. wiper switch is located in the instrument panel When you release the paddle, the washers will stop, and...
Page 191: Cruise Control
To wash the rear window when the rear wiper is already on, press the top of the switch with the wash symbol CAUTION: on it. Press in the bottom of the switch to continue the intermittent wiper cycle after the washing cycle is completed.
Page 192 Setting Cruise Control CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.
Page 193 Resuming a Set Speed Increasing Speed While Using Cruise Control Suppose you set your cruise control at a desired speed and then you apply the brake. This, of course, shuts There are two ways to go to a higher speed: off the cruise control.
Page 194 Reducing Speed While Using Cruise Using Cruise Control on Hills Control How well your cruise control will work on hills depends upon your speed, load and the steepness of the There are two ways to reduce speed while using cruise hills.
Page 195: Exterior Lamps
Exterior Lamps (Off/Auto): Turning the control to this setting will activate the automatic headlamps when it is dark enough outside and turn off all the lamps and lights during the day except the Daytime Running Lamps (DRL). (Parking Lamps): Turning the control to this setting turns on the parking lamps together with the following: •...
Page 196 Daytime Running Lamps/Automatic When it’s dark enough outside, the exterior lamps will come on automatically. When it’s bright enough outside, Headlamp System the exterior lamps will turn off and the DRL will turn on. Of course, you may still turn on the headlamps any Daytime Running Lamps (DRL) can make it easier for time you need to.
Page 197: Interior Lamps
Interior Lamps Interior Lamps Override Instrument Panel Brightness This switch is located in the overhead console The thumbwheel for this feature is located below the switchbank. exterior lamps control. Turn the thumbwheel to the right to brighten the lights or to the left to dim them. Interior Lamps Control Turn the thumbwheel all the way to the right to turn on the interior lamps, if the interior lamps override...
Page 198: Dome Lamp
Dome Lamp The interior lamps may stay on for up to 25 seconds after all doors have been closed if they have not been The dome lamp is located in the headliner and has two locked. See “Delayed Lighting” following. buttons to manually turn on and off the lamp.
Page 199: Exit Lighting
Exit Lighting Front Reading Lamps With exit lighting, the interior lamps will come on for about 25 seconds whenever you remove the key from the ignition. If you turn the ignition key to RUN or ACCESSORY, the lamps will fade out. The lamps will also fade out if you lock the doors with the power door lock switch or the remote keyless entry transmitter.
Page 200: Switchbanks
Rear Reading Lamps Battery Run-Down Protection There may be two reading lamps in the third row Your vehicle has a feature to help prevent you from headliner. draining the battery, in case you accidentally leave the interior lamps on. If you leave any interior lamps on To turn on or off either reading lamp, press the lens of while the ignition is in LOCK or OFF, they will the lamp.
Page 201: Instrument Panel Switchbank
Instrument Panel Switchbank Overhead Console Switchbank This switchbank is located in the instrument panel below This switchbank is located in the overhead console. The the comfort controls. The switchbank may include the switchbank may include the interior lamps override, rear fan knob, the rear window wiper/washer and the power sliding door(s)/override, the power rear the traction control switches.
Page 202: Ultrasonic Rear Parking Assist (Urpa)
Ultrasonic Rear Parking CAUTION: Assist (URPA) The Ultrasonic Rear Parking Assist (URPA) system is Even with the Ultrasonic Rear Park Assist designed to help you park, while the vehicle is in system, the driver must check carefully before REVERSE (R). It operates only at very low speeds, less backing up.
Page 203: How The System Works
URPA can be turned off by If an object is detected at a REVERSE (R) speed of pressing the rear park aid less than 3 mph (5 km/h), one of the following will occur: disable switch located in the instrument panel Description English Metric...
Page 204: Accessory Power Outlets
When the System Does Not Seem to Work Accessory Power Outlets Properly With accessory power outlets you can plug in electrical The light may ﬂash red when the vehicle is in equipment such as a cellular telephone or CB radio. REVERSE (R) if the ultrasonic sensors are not kept The front accessory power outlet is located below clean.
Page 205: Climate Controls
Climate Controls Certain electrical accessories may not be compatible with the accessory power outlet and could result in blown vehicle or adapter fuses. If you experience a Climate Control System problem see your dealer for additional information on accessory power outlets. With this system you can control the heating, cooling Notice: Adding any electrical equipment to your and ventilation for your vehicle.
Page 206 (Bi-Level): This mode directs half of the air to the (Recirculation): This mode keeps outside air instrument panel outlets, then directs the remaining from coming in the vehicle. It can be used to prevent air to the ﬂoor outlets. Cooler air is directed to the upper outside air and odors from entering your vehicle or help outlets and warmer air to the ﬂoor outlets.
Page 207: Defogging And Defrosting
For quick cool down on hot days, do the following: from your windshield. Use the defog mode to clear the windows of fog or moisture and warm the passengers. 1. Select the vent mode. Use the defrost mode to remove fog or frost from 2.
Page 208: Rear Window Defogger
Rear Window Defogger Outlet Adjustment The rear window defogger uses a warming grid to remove fog from the rear window. < REAR: Press this button to turn the rear window defogger on or off. An indicator light in the button will come on to let you know that the rear window defogger is activated.
Page 209: Rear Climate Control System (Without Entertainment System)
Rear Climate Control System (Without Entertainment System) Your vehicle may have a rear climate-control system that allows the driver to adjust the fan speed or a rear-seat passenger to set a separate temperature and adjust the fan speed, for the rear-seating area. This system works with the main climate-control system in your vehicle.
Page 210: Rear Air Outlets
Directing the Airﬂow If using the main climate-control panel, then the air-conditioning system must be on to direct cooled air To direct the airﬂow to the rear-seating area, use the to the rear of the vehicle. If it is not on, then the right knob located on the main climate-control panel.
Page 211: (With Entertainment System)
Rear Climate Control System (With Entertainment System) Your vehicle may have a rear climate-control system that allows the driver to adjust the fan speed or a rear-seat passenger to set a separate temperature and adjust the fan speed, for the rear-seating area. This system works with the main climate-control system in These controls are overhead, on the control your vehicle.
Page 212 Directing the Airﬂow If a rear-seat passenger is adjusting the fan speed, use the following control: To direct the airﬂow to the rear-seating area, use the FAN: Press the FAN button on the rear control panel. right knob located on the main climate-control panel. The display will show the current setting.
Page 213: Passenger Compartment Air Filter
Rear Air Outlets The access panel for the passenger compartment air ﬁlter is located in the back of the glove box. To replace To increase airﬂow through the rear ﬂoor outlets, place the ﬁlter, do the following: the left bucket seat in the second row in the forward position.
Page 214 2. Then push the tab, located on the left of the inner access panel, to the right. 3. The ﬁrst air ﬁlter will pull straight out. To remove the second, reach in and slide it toward the opening. Pull the second ﬁlter out. 4.
Page 215: Warning Lights, Gages And Indicators
Warning Lights, Gages and Gages can indicate when there may be or is a problem with one of your vehicle’s functions. Often gages Indicators and warning lights work together to let you know when there’s a problem with your vehicle. This part describes the warning lights and gages that When one of the warning lights comes on and stays on may be on your vehicle.
Page 216: Instrument Panel Cluster
Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’re going, how much fuel you’re using, and many other things you’ll need to drive safely and economically. The indicator warning lights and gages are explained on the following pages.
Page 217 Cluster with Tachometer (United States version shown, Canada similar) 3-37...
Page 218: Speedometer And Odometer
Speedometer and Odometer In addition to the standard odometer, the cluster can also display two separate trip odometers (designated by the letter A or B in the display window) as well as Your speedometer lets you see your speed in both your vehicle’s Engine Oil Life (designated by the word miles per hour (mph) and kilometers per hour (km/h).
Page 219: Tachometer
Retro-Active Reset Tachometer Each of the two trip odometers has a feature called retro-active reset. This feature can be used to set either (or both) trip odometer(s) to the number of miles (kilometers) driven since the ignition was last turned on. This can be used if you forget to reset your trip odometer at the beginning of a trip.
Page 220: Safety Belt Reminder Light
Safety Belt Reminder Light Air Bag Readiness Light When the key is turned to RUN or START, a chime will There is an air bag readiness light on the instrument come on for several seconds to remind people to panel, which shows the air bag symbol. The system fasten their safety belts.
Page 221: Brake System Warning Light
Brake System Warning Light If the air bag readiness light stays on after you start the vehicle or comes on when you are driving, your air bag system may not work properly. Have your vehicle When the ignition is on, the brake system warning light serviced right away.
Page 222: Anti-Lock Brake System Warning Light
Anti-Lock Brake System If the light comes on while you are driving, pull off the road and stop carefully. You may notice that the pedal is Warning Light harder to push. Or, the pedal may go closer to the ﬂoor. It may take longer to stop. If the light is still on, have the vehicle towed for service.
Page 223: Traction Control System (Tcs) Warning Light
Traction Control System (TCS) • If there’s a brake system problem that is speciﬁcally related to traction control, the traction control Warning Light system will turn off and the warning light will come on. If your brakes begin to overheat, the traction control system will turn off and the warning light will come on until your brakes cool down.
Page 224: Engine Coolant Temperature Gage
Engine Coolant Temperature Gage Cluster with Tachometer version (Canada) Cluster with Tachometer United States Canada version (United States) This gage shows the engine coolant temperature. If the gage pointer moves into the red area, your engine is too hot! It means that your engine coolant has overheated. If you have been operating your vehicle under normal driving conditions, you should pull off the road, stop your vehicle and turn off the engine as soon as possible.
Page 225: Malfunction Indicator Lamp
Malfunction Indicator Lamp problem and service is required. Malfunctions often will be indicated by the system before any problem is apparent. This may prevent more serious damage to Service Engine Soon Light in the your vehicle. This system is also designed to assist your United States or Check Engine Light in service technician in correctly diagnosing any Canada...
Page 226: If The Light Is Flashing
If the Light Is Flashing This light should come on, as a check to show you it is working, when the ignition is on and the engine is The following may prevent more serious damage to not running. If the light does not come on, have it your vehicle: repaired.
Page 227: If The Light Is On Steady
If the Light Is On Steady Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel. See You may be able to correct the emission system Gasoline Octane on page 5-4 . Poor fuel quality will malfunction by considering the following: cause your engine not to run as efficiently as designed.
Page 228 Emissions Inspection and Maintenance Fuel Gage Programs Some state/provincial and local governments have or may begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. Here are some things you need to know in order to help your vehicle pass an inspection: Your vehicle will not pass this inspection if the SERVICE ENGINE SOON or CHECK ENGINE light is on or not...
Page 229 Your fuel gage tells you about how much fuel you have left when the ignition is on. Here are four things that some owners ask about. All these things are normal and do not indicate that anything is wrong with the fuel gage. •...
Page 230: Message Center
Message Center When this message is displayed, the traction control system will not limit wheel spin. Adjust your driving accordingly. The message center is located in the instrument panel cluster. It gives you important safety and maintenance The message may appear for the following reasons: facts.
Page 231: Traction Active Message
Traction Active Message Engine Coolant Temperature Warning Message United States Canada United States Canada If your vehicle has the traction control system, the TRACTION ACTIVE message will appear when the This message will come on when your engine gets traction control system is limiting wheel spin. You may too hot.
Page 232: Charging System Indicator Message
Charging System Indicator Message Low Oil Pressure Message The charging system battery symbol will come on in the message center when you turn on the ignition as a check to show you it is working. United States Canada It will remain on as long as the engine is not running. It Your vehicle is equipped with a low oil pressure warning should go out once the engine is running.
Page 233: Low Engine Oil Level Message
Low Engine Oil Level Message When the engine is running and this message appears, the engine oil level may be too low. There may also be another problem causing low oil pressure. CAUTION: Do not keep driving if the oil pressure is low. If you do, your engine can become so hot that it United States Canada...
Page 234: Change Engine Oil Message
Change Engine Oil Message Power Sliding Door Warning Message United States Canada United States Canada If this message comes on and stays on after you started the engine, have the oil changed. This message will come on if the power sliding door is For additional information on when to change the oil not completely closed and the ignition is turned to and resetting the system, see Engine Oil on page 5-13 .
Page 235: Door Ajar Warning Message
Door Ajar Warning Message CAUTION: If you shift the transaxle out of PARK (P) and accelerate before the power sliding door latches closed, the door may reverse to the open position. A child or others could fall out of the vehicle and be injured. Always make United States Canada sure the power sliding door is closed and...
Page 236: Rear Hatch Ajar Warning Message
® Rear Hatch Ajar Warning Message PASS-Key III Security Message United States Canada United States Canada This message will come on when the ignition is turned If you are ever driving and this message comes on and to RUN or START and the rear hatch is open. stays on, you will be able to restart your engine if you turn it off.
Page 237: All-Wheel Drive Disable Warning Message
All-Wheel Drive Disable Warning Low Fuel Warning Message Message United States Canada United States Canada If your fuel is low, the warning message will come on and stay on until you add fuel. Your vehicle may have this message. If it does, it will If the warning message is still on after adding fuel, you come on when there is a spare tire on the vehicle, need to reset the warning message.
Page 238: Driver Information Center (Dic)
Driver Information Center (DIC) E/M (English/Metric Button): You can change the display to a metric or English reading at any time by pressing E/M. MODE: Press this button to cycle through three modes of operation – off, compass/temperature and trip computer mode.
Page 239: Compass Variance
Compass Variance Turn the ignition on and cycle the DIC to the compass/temperature mode. Press both the E/M and Compass variance is the difference between magnetic MODE buttons simultaneously for about ﬁve seconds. north and geographic north. In some areas of the The last entered variance zone number will be country, the difference is great enough to cause the displayed.
Page 240: Trip Computer
Manual Compass Calibration Trip Computer If the compass appears erratic and the calibration There are ﬁve trip computer displays available by symbol does not appear, you must manually put the pushing the MODE button. The information will appear compass into the calibration mode. in the following order: Turn the ignition on and cycle the DIC to the AVG ECON (Average Fuel Economy): This shows the...
Page 241: Audio System(S)
Audio System(s) Setting the Time for Radios without Radio Data Systems (RDS) Notice: Before you add any sound equipment to your vehicle – like a tape player, CB radio, mobile Press and hold the HR or MIN arrow for two seconds. telephone or two-way radio –...
Page 242: Am-Fm Radio
AM-FM Radio Finding a Station AM FM: Press this button to switch between FM1, FM2, or AM. The display will show your selection. TUNE: Turn this knob to select radio stations. SEEK : Press the right or the left arrow to go to the next or to the previous station and stay there.
Page 243: Setting Preset Stations
Setting Preset Stations Setting the Tone (Bass/Treble) The six numbered pushbuttons let you return to your AUDIO: To adjust the bass and the treble, press and favorite stations. You can set up to 18 stations (six FM1, release the AUDIO button until BAS or TRE appears on six FM2, and six AM) by performing the following the display.
Page 244: Adjusting Speakers
Adjusting the Speakers (Balance/Fade) To adjust both tone controls and both speaker controls to the middle position, ﬁrst end out of audio mode by pressing another button, causing the radio to perform AUDIO: To adjust the balance between the right that function, or by waiting ﬁve seconds for the display and the left speakers, press and release the AUDIO to return to time of day.
Page 245: Radio With Cd
Radio with CD volume compensation at faster vehicle speeds. Then as you drive, automatic volume increases the volume as necessary to overcome noise at any speed. The volume level should always sound the same to you as you drive. NONE will appear on the display if the radio cannot determine the vehicle speed.
Page 246 Whenever you press that numbered pushbutton, PSCAN (Preset Scan) : Press and hold one of the station you set will return and the bass the arrows for more than two seconds and the radio and treble equalization that you selected will also will produce one beep.
Page 247: Using Rds
Adjusting the Speakers (Balance/Fade) Using RDS Radio Data System (RDS): Your audio system is AUDIO: To adjust the balance between the right equipped with a Radio Data System (RDS). RDS and the left speakers, push and release the AUDIO features are available for use only on FM stations that knob until BAL appears on the display.
Page 248: Finding A Pty Station
DISPL (Display): For RDS, press this knob to change BAND (Alternate Frequency): Alternate frequency what appears on the display while using RDS. The allows the radio to switch to a stronger station with the display options are station name, RDS station frequency, same program type.
Page 249 INFO (Information): If the current station has a station that broadcasts traﬁic announcements, it will message, the information symbol will appear on the stop and TRAF will be displayed. When a traffic display. Press this button to see the message. The announcement comes on the tuned radio station you message may display the artist and song title, call in will hear it.
Page 250: Playing A Compact Disc
Playing a Compact Disc 1 PREV (Previous): Press this pushbutton to go to the previous track if the current track has been playing Insert a disc partway into the slot, label side up. The for less than eight seconds. If pressed when the current player will pull it in and the disc should begin playing.
Page 251: Compact Disc Messages
Compact Disc Messages 6 RDM (Random): Press this pushbutton to hear the tracks in random, rather than sequential, order. RDM ON If the disc comes out or CHECK CD appears on the will appear on the display. RDM T and the track display, it could be for one of the following reasons: number will appear on the display when each track starts to play.
Page 252: Radio With Cassette And Cd
Radio with Cassette and CD AUTO VOL (Automatic Volume): With automatic volume, your audio system adjusts automatically to make up for road and wind noise as you drive. Set the volume at the desired level. Press this button to select LOW, MEDIUM or HIGH. AVOL will appear on the display.
Page 253: Finding A Station
Finding a Station Setting Preset Stations The six numbered pushbuttons let you return to BAND: Press this button to switch between AM, FM, or your favorite stations. You can set up to 18 stations FM2. The display will show your selection. (six AM, six FM1 and six FM2) by performing the TUNE: Turn this knob to choose radio stations.
Page 254 Setting the Tone (Bass/Treble) Adjusting the Speakers (Balance/Fade) AUDIO: Push and release the AUDIO knob until BASS AUDIO: To adjust the balance between the right or TREB appears on the display. Turn the knob to and the left speakers, push and release the AUDIO increase or to decrease.
Page 255 Using RDS DISPL (Display): For RDS, press this knob to change what appears on the display while using RDS. The Radio Data System (RDS): Your audio system is display options are station name, RDS station frequency, equipped with a Radio Data System (RDS). RDS PTY and the name of the program (if available).
Page 256 BAND (Alternate Frequency): Alternate frequency If the whole message is not displayed, parts of it will allows the radio to switch to a stronger station with the appear every three seconds. To scroll through the same program type. Press and hold BAND for two message at your own speed, press the INFO button seconds to turn alternate frequency on.
Page 257: Playing A Cassette Tape
Traffic Interrupt Feature: Your radio can interrupt the inserted. If you hear nothing but a garbled sound, the play of a cassette, or CD. Press the TRAF button. tape may not be in squarely. Press EJT to remove The radio will seek to a station that broadcasts traffic the tape and start over.
Page 258 2 NEXT: Your tape must have at least three seconds of SIDE: Press this pushbutton to play the other side silence between each selection for next to work. of the tape. Press this pushbutton to go to the next selection on the tape.
Page 259: Cassette Tape Messages
Cassette Tape Messages CD Adapter Kits It is possible to use a portable CD player adapter kit CHK TAPE (Check Tape): If this message appears on with your cassette tape player after disabling the the radio display, the tape won’t play because of one tight/loose tape sensing feature on your tape player.
Page 260 1 PREV (Previous): Press this pushbutton to go to the 6 RDM (Random): Press this pushbutton to hear the previous track if the current track has been playing tracks in random, rather than sequential, order. RDM ON for less than eight seconds. If pressed when the current will appear on the display.
Page 261: Radio With Six-Disc Cd
Radio with Six-Disc CD TAPE CD: Press this button to play a CD when listening to the radio. Press TAPE CD to switch between the tape and compact disc if both are loaded. The inactive tape or CD will remain safely inside the radio for future listening.
Page 262 Set the volume at the desired level. Press this button to SEEK : Press the right or the left arrow to go to select MIN, MED or MAX. Each higher setting will the next or to the previous station and stay there. allow for more volume compensation at faster vehicle The radio will seek only to stations that are in the speeds.
Page 263 Setting Preset Stations Setting the Tone (Bass/Treble) The six numbered pushbuttons let you return to AUDIO: Push the AUDIO knob until BASS, MID or your favorite stations. You can set up to 18 stations TREB appears on the display. Turn the knob to increase (six AM, six FM1 and six FM2) by performing the or to decrease.
Page 264 Adjusting the Speakers (Balance/Fade) Using RDS Your audio system is equipped with a Radio Data AUDIO: To adjust the balance between the right System (RDS). RDS features are available for use only and the left speakers, push the AUDIO knob until BAL on FM stations that broadcast RDS information.
Page 265 Finding a PTY Station SCAN: You can also scan through the channels within a category by performing the following: To select and ﬁnd a desired PTY perform the following: 1. Press the P-TYPE button. P-TYPE and the last 1. Press the P-TYPE button. P-TYPE and the last selected PTY will be displayed on the screen.
Page 266: Setting Preset Ptys
Setting Preset PTYs INFO (Information): If the current station has a message, INFO will appear on the display. Press this The six numbered pushbuttons let you return to your button to see the message. The message may display favorite PTYs. These buttons have factory PTY presets. the artist and song title, call in phone numbers, etc.
Page 267 If the brackets are on the display and TRAF is not, you If an error appears on the display, see “Compact Disc can then press the TRAF button to remove the Messages” later in this section. brackets or use the TUNE knob or the SEEK arrows to LOAD CD : Press the LOAD side of this button to go to a station that supports traffic announcements.
Page 268 Playing a Speciﬁc Loaded 3. Once the light stops ﬂashing and turns green, load a disc. Insert the disc partway into the slot, label Compact Disc side up. The player will pull the disc in. For every CD loaded, a number will appear on the radio Once the disc is loaded, the light will begin ﬂashing display.
Page 269 Do not repeatedly press the CD eject side of the RDM (Random): With random, you can listen to the LOAD CD eject button to eject a disc after you have tracks in random, rather than sequential, order, on one tried to push it in manually. The receivers 25-second disc or on all of the discs.
Page 270: Using Song List Mode
Using Song List Mode SCAN : To scan one disc, press and hold either SCAN arrow for more than two seconds until SCAN The integrated six-disc CD changer has a feature called appears on the display and you hear a beep. Use this song list.
Page 271 If you attempt to save more than 20 selections, S-LIST After a track has been deleted, the remaining tracks are FULL will appear on the display. moved up the list. When another track is added to the song list, the track will be added to the end of To play the song list, press the SONG LIST button.
Page 272: Entertainment System
Compact Disc Messages Entertainment System Your vehicle may have an optional Digital Video CHECK CD: If this message appears on the radio display, it could be due to one of the following reasons: Disc (DVD) entertainment system. The entertainment system works with the vehicle’s audio system and •...
Page 273 Headphones If the channel switch located on the right side is on A, the headphones will play the DVD or auxiliary device. The entertainment system See “Stereo RCA Jacks” later in this section for includes dual channel, more information. If the channel switch is on B, the wireless headphones.
Page 274: Stereo Rca Jacks
Stereo RCA Jacks Audio Speakers The RCA jacks are located on the faceplate of the DVD Only one audio source can be heard through the player. They allow you to hook up an auxiliary device speakers at one time. such as a camcorder or a video game unit. You Audio from the radio, cassette or CD player will be may require adapter connectors or cables to connect heard through all speakers when the front audio system...
Page 275: Video Screen
Video Screen To use the video screen, do the following: 1. Push forward on the release button and the screen will fold down. 2. Pull the screen toward you and adjust its position as desired. When the video screen is not in use, push it up into its locked position.
Page 276: Dvd Player
DVD Player DVD Player Buttons SOURCE: Press this button to switch the source for the entertainment system between the auxiliary device (connected to the RCA jacks) and the DVD player. Pressing this button has no effect when there is no auxiliary device connected. (Play/Pause): Press this button to start play.
Page 277: Ejecting Disc
Remote Control Some DVDs will not allow you to fast forward or skip the copyright or previews. Some DVDs will begin playing To use the remote control, aim it at the display above the movie automatically after the previews have the video screen and press the desired button.
Page 278: Remote Control Buttons
Remote Control Buttons Fwd/ Rev (Fast Forward/Reverse): Press the right or left arrow once to fast forward or reverse the DVD. To resume play, press the button again or press the Play/Pause button. Pressing and holding an arrow will fast forward or fast reverse the DVD and play will resume when the arrow is released.
Page 279: Rear Seat Audio (Rsa) (Without
Battery Replacement passengers are not listening to. For example, rear seat passengers may listen to a cassette tape or CD To change the batteries, do the following: through headphones, while the driver listens to the radio through the front speakers. The rear seat passengers 1.
Page 280: Rear Seat Radio Controls
Rear Seat Radio Controls AM FM: Press this button to switch between AM, FM1 and FM2. If the front passengers are already listening to the radio, the RSA controller will not switch between the bands and cannot change the frequency. Press this button to play a cassette tape or a compact disc when listening to the radio.
Page 281: Rear Seat Audio (Rsa) (With
Rear Seat Audio (RSA) (With P.SET PROG (Preset Program): The front passengers must be listening to something different for each of Entertainment System) these functions to work: • Press this button to scan through the preset radio This feature allows rear seat passengers to listen to and stations set on the pushbuttons on the main radio.
Page 282: Rear Seat Radio Controls
Rear Seat Radio Controls While listening to a cassette tape, press the right arrow to hear the next selection on the tape. Press the left arrow to go back to the previous selection. These arrows are inactive if the tape mode on the front radio is in use.
Page 283: Theft-Deterrent Feature (Non-Rds Radios)
• Theft-Deterrent Feature If your vehicle has the AM-FM Radio with Six-Disc Compact Disc Player with Equalization and Radio (RDS Radios) Data System (RDS), press this button to switch to playing a different CD when multiple CDs ® THEFTLOCK is designed to discourage theft of your are loaded into the CD player.
Page 284: Understanding Radio Reception
Understanding Radio Reception tape player needs to be cleaned. It will still play tapes, but you should clean it as soon as possible to prevent damage to your tapes and player. If you notice a reduction in sound quality, try a known good cassette to see if the tape or the tape player is at fault.
Page 285: Care Of Your Cds And Dvds
Care of Your CD and DVD Player You may also choose a non-scrubbing action, wet-type cleaner which uses a cassette with a fabric belt to clean the tape head. This type of cleaning cassette will The use of CD lens cleaner discs is not advised, due to not eject on its own.
Page 286 NOTES 3-106...
Page 287: Driving Your Vehicle
Section 4 Driving Your Vehicle Your Driving, the Road, and Your Vehicle ..4-2 City Driving ..........4-20 Defensive Driving ...........4-2 Freeway Driving ...........4-21 Drunken Driving ..........4-2 Before Leaving on a Long Trip .......4-22 Control of a Vehicle ........4-5 Highway Hypnosis ........4-23 Braking ............4-6 Hill and Mountain Roads ........4-24 Traction Control System (TCS) ......4-8...
Page 288: Your Driving, The Road, And Your Vehicle
Your Driving, the Road, and the ﬂoor — makes proper defensive driving more difficult and can even cause a collision, with resulting Your Vehicle injury. Ask a passenger to help do things like this, or pull off the road in a safe place to do them yourself. These simple defensive driving techniques could save Defensive Driving your life.
Page 289 Many adults — by some estimates, nearly half the adult same BAC by drinking three 4 ounce (120 ml) glasses population — choose never to drink alcohol, so they of wine or three mixed drinks if each had 1-1/2 ounces never drive after drinking.
Page 290 There is a gender difference, too. Women generally But the ability to drive is affected well below a BAC of have a lower relative percentage of body water 0.10 percent. Research shows that the driving skills than men. Since alcohol is carried in body water, this of many people are impaired at a BAC approaching means that a woman generally will reach a higher BAC 0.05 percent, and that the effects are worse at night.
Page 291: Control Of A Vehicle
Control of a Vehicle There is something else about drinking and driving that many people do not know. Medical research shows that alcohol in a person’s system can make crash You have three systems that make your vehicle go injuries worse, especially injuries to the brain, spinal where you want it to go.
Page 292: Braking
Braking with the traffic and allow realistic following distances, you will eliminate a lot of unnecessary braking. That means better braking and longer brake life. Braking action involves perception time and reaction time. If your engine ever stops while you are driving, brake normally but do not pump your brakes.
Page 293 The anti-lock system can change the brake pressure faster than any driver could. The computer is programmed to make the most of available tire and road conditions. This can help you steer around the obstacle while braking hard. Let us say the road is wet and you are driving safely. Suddenly, an animal jumps out in front of you.
Page 294: Traction Control System (Tcs)
Remember: Anti-lock does not change the time you If you do not have anti-lock, use a “squeeze” braking need to get your foot up to the brake pedal or always technique. This will give you maximum braking decrease stopping distance. If you get too close to while maintaining steering control.
Page 295 If your vehicle is in cruise control when the traction You should turn the system off if your vehicle ever gets control system begins to limit wheel spin, the cruise stuck in sand, mud or snow and rocking the vehicle control will automatically disengage.
Page 296: Power Steering
All-Wheel Drive (AWD) System Steering If your vehicle has all-wheel drive (AWD), the AWD Power Steering system operates automatically without any action required by the driver. If the front drive wheels begin to If you lose power steering assist because the engine slip, the rear wheels will automatically begin to drive stops or the system is not functioning, you can steer but the vehicle as required.
Page 297: Steering In Emergencies
Steering in Emergencies Suppose you are steering through a sharp curve. Then you suddenly apply the brakes. Both control systems There are times when steering can be more effective — steering and braking — have to do their work where than braking.
Page 298: Off-Road Recovery
Off-Road Recovery You may ﬁnd that your right wheels have dropped off the edge of a road onto the shoulder while you’re driving. An emergency like this requires close attention and a quick decision. If you are holding the steering wheel at the recommended 9 and 3 o’clock positions, you can turn it a full 180 degrees very quickly without removing either hand.
Page 299: Passing
Passing • Do not get too close to the vehicle you want to pass while you are awaiting an opportunity. For one The driver of a vehicle about to pass another on a thing, following too closely reduces your area of two-lane highway waits for just the right moment, vision, especially if you are following a larger accelerates, moves around the vehicle ahead, then...
Page 300: Loss Of Control
• Skidding Check your mirrors, glance over your shoulder, and start your left lane change signal before moving out In a skid, a driver can lose control of the vehicle. of the right lane to pass. When you are far Defensive drivers avoid most skids by taking reasonable enough ahead of the passed vehicle to see its front care suited to existing conditions, and by not...
Page 301: Driving At Night
Driving at Night Of course, traction is reduced when water, snow, ice, gravel or other material is on the road. For safety, you will want to slow down and adjust your driving to these conditions. It is important to slow down on slippery surfaces because stopping distance will be longer and vehicle control more limited.
Page 302 Here are some tips on night driving. But if you’re driving, don’t wear sunglasses at night. They may cut down on glare from headlamps, but they • Drive defensively. also make a lot of things invisible. • Don’t drink and drive. You can be temporarily blinded by approaching •...
Page 303: Driving In Rain And On Wet Roads
Driving in Rain and on Wet Roads Rain and wet roads can mean driving trouble. On a wet road, you can’t stop, accelerate or turn as well because your tire-to-road traction isn’t as good as on dry roads. And, if your tires don’t have much tread left, you’ll get even less traction.
Page 304 CAUTION: Wet brakes can cause accidents. They will not work as well in a quick stop and may cause pulling to one side. You could lose control of the vehicle. After driving through a large puddle of water or a car wash, apply your brake pedal lightly until your brakes work normally.
Page 305: Driving Through Deep Standing Water
Hydroplaning usually happens at higher speeds. There just isn’t a hard and fast rule about hydroplaning. CAUTION: (Continued) The best advice is to slow down when it is raining. six inches of ﬂowing water can carry away a Driving Through Deep Standing Water smaller vehicle.
Page 306: City Driving
City Driving Here are ways to increase your safety in city driving: • Know the best way to get to where you are going. Get a city map and plan your trip into an unknown part of the city just as you would for a cross-country trip.
Page 307: Freeway Driving
Freeway Driving At the entrance, there is usually a ramp that leads to the freeway. If you have a clear view of the freeway as you drive along the entrance ramp, you should begin to check traffic. Try to determine where you expect to blend with the ﬂow.
Page 308: Before Leaving On A Long Trip
The exit ramp can be curved, sometimes quite sharply. Here are some things you can check before a trip: The exit speed is usually posted. • Windshield Washer Fluid: Is the reservoir full? Are Reduce your speed according to your speedometer, not all windows clean inside and outside? to your sense of motion.
Page 309: Highway Hypnosis
Highway Hypnosis What can you do about highway hypnosis? First, be aware that it can happen. Is there actually such a condition as “highway Then here are some tips: hypnosis”? Or is it just plain falling asleep at the wheel? •...
Page 310: Hill And Mountain Roads
Hill and Mountain Roads If you drive regularly in steep country, or if you’re planning to visit there, here are some tips that can make your trips safer and more enjoyable. • Keep your vehicle in good shape. Check all ﬂuid levels and also the brakes, tires, cooling system and transaxle.
Page 311 • Know how to go uphill. You may want to shift down to a lower gear. The lower gears help cool your CAUTION: engine and transaxle, and you can climb the hill better. Coasting downhill in NEUTRAL (N) or with the •...
Page 312: Winter Driving
Winter Driving Here are some tips for winter driving: • Have your vehicle in good shape for winter. • You may want to put winter emergency supplies in your vehicle. Include an ice scraper, a small brush or broom, a supply of windshield washer ﬂuid, a rag, some winter outer clothing, a small shovel, a ﬂashlight, a red cloth and a couple of reﬂective warning triangles.
Page 313: Driving On Snow Or Ice
Driving on Snow or Ice What’s the worst time for this? “Wet ice.” Very cold snow or ice can be slick and hard to drive on. But wet Most of the time, those places where your tires meet ice can be even more trouble because it may offer the road probably have good traction.
Page 314: If You're Caught In A Blizzard
If You’re Caught in a Blizzard Unless you have the anti-lock braking system, you’ll want to brake very gently, too. (If you do have anti-lock, see Braking on page 4-6 . This system improves your vehicle’s stability when you make a hard stop on a slippery road.) Whether you have the anti-lock braking system or not, you’ll want to begin stopping sooner than you would on dry pavement.
Page 315 • Tie a red cloth to your vehicle to alert police that you’ve been stopped by the snow. CAUTION: • Put on extra clothing or wrap a blanket around you. If you have no blankets or extra clothing, make Snow can trap exhaust gases under your body insulators from newspapers, burlap bags, rags, vehicle.
Page 316: If You Are Stuck: In Sand, Mud
Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine CAUTION: again and repeat this only when you feel really uncomfortable from the cold. But do it as little as possible.
Page 317: Rocking Your Vehicle To Get It Out
Notice: Spinning your wheels can destroy parts of Rocking Your Vehicle To Get It Out your vehicle as well as the tires. If you spin the First, turn your steering wheel left and right. That will wheels too fast while shifting your transaxle back clear the area around your front wheels.
Page 318: Towing
Towing With the proper preparation and equipment, many vehicles can be towed in these ways. See “Dinghy Towing” and “Dolly Towing,” following. Towing Your Vehicle Here are some important things to consider before you do recreational vehicle towing: Consult your dealer or a professional towing service if •...
Page 319: Dinghy Towing
Dinghy Towing Dolly Towing Your vehicle was not designed to be towed with all of its If you have a two-wheel-drive vehicle, it can be towed wheels on the ground. If you have a two-wheel-drive with two of its wheels on the ground. To dolly tow vehicle, it can be towed with two of its wheels on your vehicle, do the following: the ground.
Page 320: Loading Your Vehicle
Loading Your Vehicle The Certiﬁcation/Tire label also tells you the maximum weights for the front and rear axles, called the Gross Axle Weight Rating (GAWR). To ﬁnd out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle.
Page 321: Automatic Level Control
Automatic Level Control If you put things inside your vehicle – like suitcases, tools, packages, or anything else – they will go as fast On vehicles equipped with the automatic level control, as the vehicle goes. If you have to stop or turn the rear of the vehicle is automatically kept level as you quickly, or if there is a crash, they’ll keep going.
Page 322: Towing A Trailer
Towing a Trailer Your vehicle can tow a trailer. To identify what the vehicle trailering capacity is for your vehicle, you should read the information in “Weight of the Trailer” that appears later in this section. But trailering is different CAUTION: than just driving your vehicle by itself.
Page 323: P.o. Box
You can ask your dealer for our trailering information and don’t make starts at full throttle. This helps your or advice, or you can write us at: engine and other parts of your vehicle wear in at Chevrolet Customer Assistance Center the heavier loads. P.O. Box 33170 •...
Page 324: Weight Of The Trailer Tongue
Weight of the Trailer Tongue If you’re using a weight-carrying or a weight-distributing hitch, the trailer tongue weight (A) should be 10 percent The tongue load (A) of any trailer is an important weight to 15 percent of the total loaded trailer weight (B). to measure because it affects the total or gross weight Do not exceed the maximum allowable tongue weight of your vehicle.
Page 325: Safety Chains
Hitches Safety Chains It’s important to have the correct hitch equipment. You should always attach chains between your vehicle Crosswinds, large trucks going by and rough roads are and your trailer. Cross the safety chains under the a few reasons why you’ll need the right hitch. Here tongue of the trailer to help prevent the tongue from are some rules to follow: contacting the road if it becomes separated from...
Page 326: Driving With A Trailer
Driving with a Trailer Towing a trailer requires a certain amount of experience. Before setting out for the open road, you’ll want to get to know your rig. Acquaint yourself with the feel of handling and braking with the added weight of the trailer. CAUTION: And always keep in mind that the vehicle you are driving is now a good deal longer and not nearly as...
Page 327: Following Distance
Following Distance Making Turns Stay at least twice as far behind the vehicle ahead as Notice: Making very sharp turns while trailering you would when driving your vehicle without a trailer. could cause the trailer to come in contact with the This can help you avoid situations that require vehicle.
Page 328: Driving On Grades
Driving on Grades Parking on Hills Reduce speed and shift to a lower gear before you start down a long or steep downgrade. If you don’t shift CAUTION: down, you might have to use your brakes so much that they would get hot and no longer work well. You really should not park your vehicle, with a If you are towing a trailer that weighs more than 1,000 lbs.
Page 329: Maintenance Schedule
When You Are Ready to Leave After Maintenance When Trailer Towing Parking on a Hill Your vehicle will need service more often when you’re pulling a trailer. See the Maintenance Schedule for more 1. Apply your regular brakes and hold the pedal down on this.
Page 330 NOTES 4-44...
Page 331: Service And Appearance Care
Section 5 Service and Appearance Care Service ............5-3 Battery ............5-43 Doing Your Own Service Work ......5-3 Jump Starting ..........5-44 Adding Equipment to the Outside of All-Wheel Drive ..........5-50 Your Vehicle ..........5-4 Bulb Replacement ..........5-52 Fuel ..............5-4 Halogen Bulbs ..........5-52 Gasoline Octane ..........5-4 Headlamps ..........5-52 Gasoline Speciﬁcations ........5-5 Front Turn Signal, Sidemarker and...
Page 332 Section 5 Service and Appearance Care Appearance Care ..........5-87 Vehicle Identiﬁcation ........5-95 Cleaning the Inside of Your Vehicle ....5-87 Vehicle Identiﬁcation Number (VIN) ....5-95 Care of Safety Belts and Built-in Child Service Parts Identiﬁcation Label .....5-95 Restraint Harness ........5-90 Electrical System ..........5-96 Weatherstrips ..........5-90 Add-On Electrical Equipment ......5-96 Cleaning the Outside of Your Vehicle ....5-90...
Page 333: Service
Service Doing Your Own Service Work If you want to do some of your own service work, you Your dealer knows your vehicle best and wants you to will want to use the proper service manual. It tells be happy with it. We hope you will go to your dealer you much more about how to service your vehicle than for all your service needs.
Page 334: Adding Equipment To The Outside Of
Fuel CAUTION: (Continued) Use of the recommended fuel is an important part of the proper maintenance of your vehicle. • Be sure to use the proper nuts, bolts and other fasteners. “English” and “metric” Gasoline Octane fasteners can be easily confused. If you use the wrong fasteners, parts can later Use regular unleaded gasoline with a posted octane break or fall off.
Page 335: Gasoline Speciﬁcations
Gasoline Speciﬁcations California Fuel It is recommended that gasoline meet speciﬁcations If your vehicle is certiﬁed to meet California Emission which were developed by the American Automobile Standards (see the underhood emission control label), it Manufacturers Association and endorsed by the is designed to operate on fuels that meet California Canadian Vehicle Manufacturers Association for better speciﬁcations.
Page 336: Additives
Additives tricarbonyl (MMT); ask the attendant where you buy gasoline whether the fuel contains MMT. General Motors does not recommend the use of such gasolines. To provide cleaner air, all gasolines in the United States Fuels containing MMT can reduce the life of spark plugs are now required to contain additives that will help and the performance of the emission control system prevent engine and fuel system deposits from forming,...
Page 337: Filling Your Tank
Filling Your Tank CAUTION: Fuel vapor is highly ﬂammable. It burns violently, and that can cause very bad injuries. Do not smoke if you are near fuel or refueling your vehicle. Keep sparks, ﬂames and smoking materials away from fuel. The fuel door is located on the driver’s side of the vehicle.
Page 338 CAUTION: If you get fuel on yourself and then something ignites it, you could be badly burned. Fuel can spray out on you if you open the fuel cap too quickly. This spray can happen if your tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any “hiss”...
Page 339: Filling A Portable Fuel Container
Filling a Portable Fuel Container When you put the fuel cap back on, turn it to the right (clockwise) until you hear a clicking sound. Make sure you fully install the cap. The diagnostic system can determine if the fuel cap has been left off or improperly CAUTION: installed.
Page 340: Checking Things Under The Hood
Checking Things Under Hood Release the Hood To open the hood, do the following: CAUTION: An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing and tools away from any underhood electric fan.
Page 341 4. Pull forward on the hood prop to release it from its Before closing the hood, be sure all the ﬁller caps are storage clip. on properly. Then follow these steps: The hood prop may be hot due to increased engine 6.
Page 342: Engine Compartment Overview
Engine Compartment Overview When you lift the hood, you’ll see these items: 5-12...
Page 343: Engine Oil
A. Underhood Fuse Block. See Fuses and Circuit Engine Oil Breakers on page 5-96 . B. Remote Positive (+) Terminal. See Jump Starting on page 5-44 . C. Windshield Washer Fluid Reservoir. See Windshield Washer Fluid on page 5-38 . D.
Page 344: Checking Engine Oil
Checking Engine Oil Turn off the engine and give the oil several minutes to drain back into the oil pan. If you don’t, the oil It’s a good idea to check your engine oil every time you dipstick might not show the actual level. get fuel.
Page 345: When To Add Engine Oil
When to Add Engine Oil The engine oil ﬁll cap is located behind the engine If the oil is at or below the cross-hatched area at the tip oil dipstick. See Engine of the dipstick, then you’ll need to add at least one Compartment Overview on quart of oil.
Page 346: What Kind Of Engine Oil To Use
What Kind of Engine Oil to Use Oils recommended for your vehicle can be identiﬁed by looking for the starburst symbol. This symbol indicates that the oil has been certiﬁed by the American Petroleum Institute (API). Do not use any oil which does not carry this starburst symbol. If you choose to perform the engine oil change service yourself, be sure...
Page 347: Engine Oil Additives
When to Change Engine Oil As in the chart shown previously, SAE 5W-30 is the only viscosity grade recommended for your vehicle. You (GM Oil Life System) should look for and use only oils which have the API Starburst symbol and which are also identiﬁed as Your vehicle has a computer system that lets you know SAE 5W-30.
Page 348: What To Do With Used Oil
How to Reset the Change Engine Oil What to Do with Used Oil Message Used engine oil contains certain elements that may be unhealthy for your skin and could even cause cancer. The GM Oil Life System calculates when to change Don’t let used oil stay on your skin for very long.
Page 349: How To Inspect The Engine Air Cleaner/Filter
How to Inspect the Engine Air 4. Remove and replace the engine air cleaner/ﬁlter. Cleaner/Filter 5. Align the tabs located on the bottom of the panel with the slots at the bottom of the housing. To inspect the air cleaner/ﬁlter, remove the ﬁlter from 6.
Page 350: Automatic Transaxle Fluid
Automatic Transaxle Fluid How to Check Automatic Transaxle Fluid When to Check and Change Automatic Because this operation can be a little difficult, you may Transaxle Fluid choose to have this done at the dealership service department. A good time to check your automatic transaxle ﬂuid If you do it yourself, be sure to follow all the instructions level is when the engine oil is changed.
Page 351: Checking The Fluid Level
Checking the Fluid Level Then, without shutting off the engine, follow these steps: Prepare your vehicle as follows: • Park your vehicle on a level place. Keep the engine running. • With the parking brake applied, place the shift lever in PARK (P).
Page 352: Maintenance Schedule
How to Add Fluid Automatic Transaxle The dipstick has a bright, red loop design for easy identiﬁcation. See Engine Compartment Overview on Fluid page 5-12 for more information on location. Refer to the Maintenance Schedule to determine what 1. Pull out the dipstick and wipe it with a clean rag or kind of transaxle ﬂuid to use.
Page 353: Engine Coolant
Engine Coolant • Protect against rust and corrosion. • Help keep the proper engine temperature. The cooling system in your vehicle is ﬁlled with ® • DEX-COOL engine coolant. This coolant is designed Let the warning messages and gages work as they to remain in your vehicle for 5 years or 150,000 miles should.
Page 354: What Engine Coolant To Use
What Engine Coolant to Use If you have to add coolant more than four times a year, have your dealer check your cooling system. Use a mixture of one-half clean, drinkable water and ® one-half DEX-COOL coolant which won’t damage Notice: If you use the proper coolant, you don’t aluminum parts.
Page 355: Adding Coolant
Adding Coolant Add coolant mixture at the coolant recovery tank, but be careful not to spill it. ® If you need more coolant, add the proper DEX-COOL coolant mixture at the coolant recovery tank. CAUTION: CAUTION: You can be burned if you spill coolant on hot engine parts.
Page 356: Radiator Pressure Cap
Radiator Pressure Cap Overheated Engine Protection Operating Mode Notice: The radiator cap on your vehicle is a pressure-type cap and must be tightly installed to This emergency operating mode allows your vehicle to prevent coolant loss and possible engine damage be driven to a safe place in an emergency situation.
Page 357: If Steam Is Coming From Your Engine
If Steam Is Coming From Your Engine CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down.
Page 358: If No Steam Is Coming From Your Engine
If No Steam Is Coming From Your If you no longer have the overheat warning, you can drive. Just to be safe, drive slower for about 10 minutes. Engine If the warning doesn’t come back on, you can drive normally. If you get an engine overheat warning but see or hear no steam, the problem may not be too serious.
Page 359: Cooling System
Cooling System CAUTION: When you decide it’s safe to lift the hood, here’s what you’ll see: An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan.
Page 360 CAUTION: Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine ﬁre, and you could be burned.
Page 361 Notice: Engine damage from running your engine without coolant isn’t covered by your warranty. CAUTION: See “Overheated Engine Protection Operating Mode” in the Index for information on driving to a safe place in an emergency. Adding only plain water to your cooling system can be dangerous.
Page 362 CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. When the coolant in the coolant recovery tank is at or above the FULL COLD mark, start your vehicle.
Page 363 CAUTION: Steam and scalding liquids from a hot cooling system can blow out and burn you badly. They are under pressure, and if you turn the radiator pressure cap — even a little — they can come out at high speed. Never turn the cap when the cooling system, including the radiator pressure cap, is hot.
Page 364: How To Add Coolant To The Radiator
How to Add Coolant to the Radiator If you hear a hiss, wait for that to stop. A hiss means there is still some pressure left. Notice: Your engine has a speciﬁc radiator ﬁll procedure. Failure to follow this procedure could cause your engine to overheat and be severely damaged.
Page 365 CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. ® 4. Fill the radiator with the proper DEX-COOL coolant mixture, up to the base of the ﬁller neck.
Page 366 6. Start the engine and let it run until you can feel the 8. Then replace the pressure cap. At any time during upper radiator hose getting hot. Watch out for the this procedure if coolant begins to ﬂow out of the engine cooling fans.
Page 367: Power Steering Fluid
Power Steering Fluid 9. Then ﬁll the coolant recovery tank to the FULL COLD mark. When to Check Power Steering Fluid 10. Put the cap back on the coolant recovery tank. It is not necessary to regularly check power steering ﬂuid unless you suspect there is a leak in the system or you hear an unusual noise.
Page 368: Windshield Washer Fluid
How to Check Power Steering Fluid Windshield Washer Fluid Turn the key off, let the engine compartment cool down, What Washer Fluid to Use wipe the cap and the top of the reservoir clean, then unscrew the cap and wipe the dipstick with a clean rag. When you need windshield washer ﬂuid, be sure to read Replace the cap and completely tighten it.
Page 369: Adding Washer Fluid
Adding Washer Fluid Notice: • When using concentrated washer ﬂuid, follow Open the cap with the the manufacturer’s instructions for adding washer symbol on it. Add water. washer ﬂuid until the • Don’t mix water with ready-to-use washer ﬂuid. tank is full. Water can cause the solution to freeze and damage your washer ﬂuid tank and other parts of the washer system.
Page 370: Brakes
Brakes normal brake lining wear. When new linings are put in, the ﬂuid level goes back up. The other reason is that ﬂuid is leaking out of the brake system. If it is, you Brake Fluid should have your brake system ﬁxed, since a leak means that sooner or later your brakes will not work well, or will not work at all.
Page 371 CAUTION: With the wrong kind of ﬂuid in your brake system, your brakes may not work well, or they may not even work at all. This could cause a crash. Always use the proper When your brake ﬂuid falls to a low level, your brake brake ﬂuid.
Page 372: Brake Wear
Brake Wear Notice: Continuing to drive with worn-out brake pads could result in costly brake repair. Your vehicle has front disc brakes and may have rear Some driving conditions or climates may cause a brake drum brakes or rear disc brakes. squeal when the brakes are ﬁrst applied or lightly Disc brake pads have built-in wear indicators that make applied.
Page 373: Battery
Brake Pedal Travel Battery See your dealer if the brake pedal does not return to Your new vehicle comes with a maintenance free normal height, or if there is a rapid increase in ® ACDelco battery. When it is time for a new battery, get pedal travel.
Page 374: Vehicle Storage
Vehicle Storage Jump Starting If you are not going to drive your vehicle for 25 days If your battery has run down, you may want to use or more, remove the black, negative (−) cable from another vehicle and some jumper cables to start your the battery.
Page 375 Notice: Ignoring these steps could result in costly Notice: If you leave your radio or other accessories damage to your vehicle that wouldn’t be covered on during the jump starting procedure, they could by your warranty. be damaged. The repairs would not be covered by your warranty.
Page 376 The terminal is located under a tethered cap at CAUTION: the front of the underhood fuse block. See Engine Compartment Overview on Using a match near a battery can cause battery page 5-12 for more gas to explode. People have been hurt doing information on location.
Page 377 7. Don’t let the other end touch metal. Connect it CAUTION: to the positive (+) terminal of the good battery. Use a remote Fans or other moving engine parts can injure positive (+) terminal you badly. Keep your hands away from moving if the vehicle has one.
Page 378 Don’t let the other end touch anything until the next 10. Now start the vehicle with the good battery and run step. The other end of the negative (−) cable the engine for a while. doesn’t go to the dead battery. It goes to a heavy, 11.
Page 379 To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative (−) cable from the vehicle that had the dead battery. 2. Disconnect the black negative (−) cable from the vehicle with the good battery. 3.
Page 380: All-Wheel Drive
All-Wheel Drive How to Check Lubricant If you have an all-wheel-drive vehicle, be sure to perform the lubricant checks described in this section. However, they have two additional systems that need lubrication. Transfer Case (Power Transfer Unit) When to Check Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant.
Page 381: Carrier Assembly-Differential
Carrier Assembly-Differential To get an accurate reading, the vehicle should be on a level surface. (Rear Drive Module) If the level is below the bottom of the ﬁller plug hole, When to Check and Change Lubricant you’ll need to add some lubricant. Add enough lubricant Refer to the Maintenance Schedule to determine how to raise the level to the bottom of the ﬁller plug hole.
Page 382: Bulb Replacement
Bulb Replacement Headlamps 1. Open the hood. For the type of bulbs, see Replacement Bulbs on page 5-57 . 2. Remove the front turn signal/parking lamp assembly. See Front Turn Signal, Sidemarker and For any bulb changing procedure not listed in this Parking Lamps on page 5-54 .
Page 383 6. Unhook the electrical connector by lifting up the blue tabs and pulling the bulb out. 8. Carefully put the bulb assembly back into the lamp housing. Be careful not to damage the bulb on the headlamp aiming bar. 7. Install the new bulb through the black retainer ring and into the electrical connector.
Page 384: Front Turn Signal, Sidemarker And Parking Lamps
Front Turn Signal, Sidemarker and Parking Lamps 1. Open the hood. 9. Align the pins on the bottom of the headlamp assembly with the holes in the lamp support bracket. 10. To reinstall the front turn signal/parking lamp assembly. See Front Turn Signal, Sidemarker 2.
Page 385 Front Turn Signal/Parking Lamp Front Sidemarker Lamp 4. Unscrew the bulb socket from the lamp assembly by pressing the tab while turning it counterclockwise. 5. Replace the bulb by pulling the old one out and gently pushing the new one into the lamp socket. 6.
Page 386: Taillamps, Turn Signal, Stoplamps And Back-Up Lamps
Taillamps, Turn Signal, Stoplamps and Back-up Lamps 1. Open the liftgate. 2. Remove the two screws from the taillamp housing on the inboard side. 3. Pull off the entire taillamp housing. The locator/retaining pins on the outboard side are part of the lamp assembly and will remain intact during removal.
Page 387: Replacement Bulbs
5. Replace the bulb by pulling the old bulb out and gently pushing the new bulb into the bulb holder socket. 6. Snap the bulb holder back into place, making sure all retaining tabs are properly over the bulb holder tabs. 7.
Page 388: Windshield Wiper Blade Replacement
Windshield Wiper Blade To remove the windshield wiper blade(s): 1. Turn the wipers on to the lowest intermittent setting. Replacement 2. Turn the ignition to OFF while the wipers are at Windshield wiper blades should be inspected at least the outer position of the wipe pattern. twice a year for wear or cracking.
Page 389 5. Push the release clip at the connecting point of the blade and the arm up. Then pull the blade assembly down toward the glass to remove it from the wiper arm. 6. Push the new wiper blade securely on the wiper arm until you hear the release clip “click”...
Page 390: Tires
Underinﬂated tires pose the same danger about your tire warranty and where to obtain service, as overloaded tires. The resulting accident see your Chevrolet Warranty booklet for details. could cause serious injury. Check all tires frequently to maintain the recommended pressure.
Page 391: How To Check
Inﬂation - Tire Pressure If your tires have too much air (overinﬂation), you can get the following: The Certiﬁcation/Tire label, which is on the rear edge of • Unusual wear the driver’s door, shows the correct inﬂation pressures • Bad handling for your tires when they’re cold.
Page 392: Tire Inspection And Rotation
Tire Inspection and Rotation When rotating your tires, always use the correct rotation pattern shown here. Tires should be rotated every 7,500 miles (12 500 km). Don’t include the compact spare tire in your tire rotation. Any time you notice unusual wear, rotate your tires as soon as possible and check wheel alignment.
Page 393: When It Is Time For New Tires
When It Is Time for New Tires You need a new tire if any of the following statements are true: • You can see the indicators at three or more places One way to tell when it’s time for new tires is to around the tire.
Page 394: Buying New Tires
Buying New Tires CAUTION: To ﬁnd out what kind and size of tires you need, look at the Certiﬁcation/Tire label. Mixing tires could cause you to lose control The tires installed on your vehicle when it was new had while driving. If you mix tires of different sizes a Tire Performance Criteria Speciﬁcation (TPC Spec) number on each tire’s sidewall.
Page 395: Uniform Tire Quality Grading
Uniform Tire Quality Grading Treadwear The treadwear grade is a comparative rating based on Quality grades can be found where applicable on the the wear rate of the tire when tested under controlled tire sidewall between tread shoulder and maximum conditions on a speciﬁed government test course.
Page 396: Wheel Alignment And Tire Balance
Temperature – A, B, C Scheduled wheel alignment and wheel balancing are not needed. However, if you notice unusual tire wear or The temperature grades are A (the highest), B, and C, your vehicle pulling one way or the other, the alignment representing the tire’s resistance to the generation may need to be reset.
Page 397: Tire Chains
Used Replacement Wheels CAUTION: CAUTION: Using the wrong replacement wheels, wheel bolts or wheel nuts on your vehicle can be Putting a used wheel on your vehicle is dangerous. It could affect the braking and dangerous. You can’t know how it’s been used handling of your vehicle, make your tires lose or how far it’s been driven.
Page 398: Accessory Inﬂator
Accessory Inﬂator CAUTION: Your vehicle may have an accessory inﬂator. With it, you can inﬂate things like air mattresses and basketballs, and you can also use it to bring your tires Inﬂating something too much can make it up to the proper pressure. explode, and you or others could be injured.
Page 399 If the accessory inﬂator system does not turn on or the After running the accessory inﬂator for 30 minutes, wait light does not come on, the fuse may be blown or at least 10 minutes before restarting the accessory installed incorrectly. See Fuses and Circuit Breakers on inﬂator.
Page 400: If A Tire Goes Flat
If a Tire Goes Flat CAUTION: It’s unusual for a tire to “blowout” while you’re driving, especially if you maintain your tires properly. If air goes out of a tire, it’s much more likely to leak out slowly. Lifting a vehicle and getting under it to do But if you should ever have a “blowout,”...
Page 401: Changing A Flat Tire
Changing a Flat Tire If a tire goes ﬂat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your hazard warning ﬂashers. CAUTION: Changing a tire can cause an injury. The vehicle can slip off the jack and roll over you or other people.
Page 402: Removing The Spare Tire And Tools
Removing the Spare Tire and Tools The tools you’ll need are located in the storage compartment at the rear of the vehicle, on the passenger’s side. A. Jack E. Jacking B. Strap Instructions To remove the tools, do the following: C.
Page 403 A. Hoist Shaft E. Extension The tools you’ll be using include the jack (A), B. Hoist Assembly (Chisel End) extension (B) and folding wrench (C). C. Retainer F. Folding Wrench The compact spare tire is located under the rear of the D.
Page 404 4. If your vehicle is an all-wheel-drive vehicle, after removing the compact spare tire turn the wrench clockwise to raise the cable back up. On an AWD vehicle, you can not store a full-size tire under the vehicle. It should be stowed inside the vehicle by the cable provided.
Page 405: Secondary Latch System
Secondary Latch System CAUTION: Your vehicle may have an underbody mounted tire hoist assembly equipped with a secondary latch system. It’s designed to stop a tire from suddenly falling off your Before beginning this procedure read all the vehicle if the cable holding the spare tire is damaged. instructions.
Page 406 1. Place the jack under the vehicle, ahead of the rear 5. Grasp the compact spare tire with both hands and bumper. Position the center lift point of the jack pull it out from under the vehicle. under the center of the compact spare tire. 6.
Page 407: Removing The Wheel Covers
Removing the Wheel Covers Removing the Flat Tire and Installing the Spare Tire If the wheel has a center cap, use the handle of the folding wrench to pry it off. Then, with the other end of 1. Loosen the wheel nuts the folding wrench, loosen the nuts.
Page 408 2. Near each wheel, there Do not raise the vehicle yet. Put the compact spare is a notch in the tire near you. vehicle’s body. Position the jack and raise CAUTION: the jack head until it ﬁts ﬁrmly into the notch in the vehicle’s frame Getting under a vehicle when it is jacked up is nearest the ﬂat tire.
Page 409 3. Attach the folding wrench to the jack, and CAUTION: turn the wrench clockwise to raise the jack head a few Raising your vehicle with the jack improperly inches. positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to ﬁt the jack lift head into the proper location before raising the vehicle.
Page 410 6. Remove any rust or dirt from the wheel bolts, CAUTION: mounting surfaces and spare wheel. Never use oil or grease on studs or nuts. If you do, the nuts might come loose. Your wheel could fall off, causing a serious accident. 7.
Page 411 9. Tighten the wheel nuts ﬁrmly in a crisscross sequence, as shown. CAUTION: 8. Lower the vehicle by attaching the folding wheel wrench to the jack and turning the wrench Incorrect wheel nuts or improperly tightened counterclockwise. Lower the jack completely. wheel nuts can cause the wheel to come loose and even come off.
Page 412: Storing A Flat Or Spare Tire And Tools
Notice: Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid CAUTION: expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque speciﬁcation. See “Capacities and The underbody-mounted spare tire needs to be Speciﬁcations”...
Page 413: Storing The Spare Tire And Tools
Storing the Spare Tire and Tools 1. Lay the tire near the rear of the vehicle with the valve stem down. 2. If the vehicle has aluminum wheels, remove the small center cap by tapping the back of the cap with the extension of the shaft.
Page 414 Put back all tools as they were stored in the jack Store the center cap or the plastic “bolt-on” wheel storage compartment and put the compartment cover covers until a full size tire is put back on the vehicle. back on. When you replace the compact spare with a full-size tire, reinstall the bolt-on wheel covers or the center cap.
Page 415 5. Hook the cable onto the outside portion of the liftgate hinges. 6. Pull on the cable to make sure it is secure. 7. Make sure the metal tube is centered at the A. Cable striker. Push the B. Liftgate Hinges tube towards the front C.
Page 416: Compact Spare Tire
Compact Spare Tire Notice: Tire chains won’t ﬁt your compact spare. Using them can damage your vehicle and can damage the chains too. Don’t use tire chains on Although the compact spare tire was fully inﬂated when your compact spare. your vehicle was new, it can lose air after a time.
Page 417: Appearance Care
Appearance Care • Lacquer Thinner • Nail Polish Remover Remember, cleaning products can be hazardous. Some are toxic. Others can burst into ﬂames if you strike a They can all be hazardous — some more than match or get them on a hot part of the vehicle. Some are others —...
Page 418: Cleaning Fabric/Carpet
Cleaning Fabric/Carpet 3. Follow the directions on the container label. 4. Apply cleaner with a clean sponge. Don’t saturate Your dealer has cleaners for the cleaning of fabric and the material and don’t rub it roughly. carpet. They will clean normal spots and stains very well.
Page 419: Cleaning The Top Of The Instrument Panel
Cleaning the Top of the Instrument Stains caused by candy, ice cream, mayonnaise, chili sauce and unknown stains can be removed as follows: Panel 1. Carefully scrape off excess stain. Use only mild soap and water to clean the top surfaces 2.
Page 420: Care Of Safety Belts And Built-In Child Restraint Harness
Cleaning Built-In Child Restraint Pad Weatherstrips The built-in child restraint pad is attatched to the Silicone grease on weatherstrips will make them last seat frame with fastener strips. You can remove the pad longer, seal better, and not stick or squeak. Apply and hand wash it with mild soap and water.
Page 421: Finish Care
Finish Care Don’t wash your vehicle in the direct rays of the sun. Use a car washing soap. Don’t use strong soaps Occasional waxing or mild polishing of your vehicle by or chemical detergents. Be sure to rinse the vehicle hand may be necessary to remove residue from the well, removing all soap residue completely.
Page 422: Cleaning Aluminum Wheels
Cleaning Aluminum Wheels Exterior painted surfaces are subject to aging, weather and chemical fallout that can take their toll over a Keep your wheels clean using a soft clean cloth with period of years. You can help to keep the paint ﬁnish mild soap and water.
Page 423: Sheet Metal Damage
Sheet Metal Damage At least every spring, ﬂush these materials from the underbody with plain water. Clean any areas where mud and debris can collect. Dirt packed in close areas of If your vehicle is damaged and requires sheet metal the frame should be loosened before being ﬂushed.
Page 424: Vehicle Care/Appearance Materials
Vehicle Care/Appearance Materials Vehicle Care/Appearance Materials (cont’d) See your GM dealer for more information on purchasing Description Usage the following products. Removes swirl marks, ﬁne Swirl Remover Polish scratches and other light Vehicle Care/Appearance Materials surface contamination. Description Usage Removes light scratches Cleaner Wax Polishing Cloth Interior and exterior...
Page 425: Vehicle Identiﬁcation
Vehicle Identiﬁcation Engine Identiﬁcation The 8th character in your VIN is the engine code. This code will help you identify your engine, speciﬁcations Vehicle Identiﬁcation Number (VIN) and replacement parts. Service Parts Identiﬁcation Label You’ll ﬁnd this label on the inside of the glove box door. It’s very helpful if you ever need to order parts.
Page 426: Electrical System
Electrical System Power Windows and Other Power Options Add-On Electrical Equipment Circuit breakers in the instrument panel fuse panel protect the power windows and other power accessories. Notice: Don’t add anything electrical to your vehicle When the current load is too heavy, the circuit breaker unless you check with your dealer ﬁrst.
Page 427: Instrument Panel Fuse Block
Instrument Panel Fuse Block The instrument panel fuse block is located to the right of the glove box on the end of the instrument panel. Fuse Usage Pull the door open to access the instrument panel Steering Wheel Radio Control fuse block.
Page 428 Fuse Usage Fuse Usage HTD MIRROR Heated Mirrors Inﬂatable Restraint Control Module RH T/LP Driver’s Side Taillamp (Export Only) HVAC Heater-A/C Control BLOWER RR FOG LP Fog Lamps (Export Only) Instrument Cluster, Body Control CIGAR/DIC/ Cigarette Lighter, DIC, Front MALL Module, Electronic Level Control APO FRT Auxiliary Power Outlets, Data Link...
Page 429 Fuse Usage Fuse Usage Rear Window Wiper Motor, Rear BCM PRGRAM BCM Programming Window Wiper/Washer and RH HEAD LP Driver’s Side Low Beam Headlamp WPR/WSHR Multifunction Switch (Rear Window (Export Only) Wiper/Washer Switch) RH HEAD LP Driver’s Side High Beam Headlamp LH HEADLP Passenger’s Side Low Beam HIGH...
Page 430: Underhood Fuse Block
Underhood Fuse Block This fuse block is located in the engine compartment, in front of the windshield washer ﬂuid reservoir. See Engine Compartment Overview on page 5-12 for more information on location. Fuse Usage Coolant Fans Not Used The fuses marked spare are available if a replacement Circuit Breakers: Front Comfort fuse is needed.
Page 431 Fuse Usage Fuse Usage Ignition Switch to Fuses (Instrument Fuel Injectors 1–6 Panel): ABS/TCS Ignition, Cruise, Not Used DRL, Electronic PRNDL, Ignition 1, Not Used AWD, PSD, Air Bag, Turn Signal Evaporative Emissions (EVAP) and Powertrain Control Module [IGN MAIN Relay (Underhood Fuse Canister Purge Valve, Heated Block: A/C Clutch, Electronic Oxygen Sensors 1 and 2, Mass Air...
Page 432 Fuse Usage Fuse Usage Generator Automatic Transaxle (Torque Mini Fuse Puller Converter Clutch Solenoids) § Air Conditioning Clutch Diode Stoplamp Switch to Powertrain Control Module Fuel Pump Relay Relay Usage Powertrain Control Module Right Fan 1, Left Fan 2 Not Used Left Fan 2 Fog Lamp Relay Fuses: A/C Clutch, Ignition 1-U/H,...
Page 433: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric measurements. Please refer to Part D: Recommended Fluids and Lubricants on page 6-17 for more information. Capacities Application English Metric Air Conditioning Refrigerant Systems Front A/C 1.7 lbs. 0.8 kg Front and Rear A/C 2.2 lbs.
Page 434: Normal Maintenance Replacement Parts
Engine Speciﬁcations Engine VIN Code Transaxle Spark Plug Gap Firing Order 0.060 inches Automatic 1–2–3–4–5–6 (1.52 mm) Normal Maintenance Replacement Parts Part Number Engine Air Cleaner/Filter A-1208C* Engine Oil Filter PF47 Passenger Compartment Air Filter Kit GM Part No. 52482929 Spark Plugs 41-101* Windshield Wiper Blades...
Page 435 Section 6 Maintenance Schedule Maintenance Schedule ........6-2 At Least Once a Year ........6-12 Introduction ...........6-2 Part C: Periodic Maintenance Inspections ..6-15 Your Vehicle and the Environment ....6-2 Steering, Suspension and Front Drive Axle Maintenance Requirements ......6-2 Boot and Seal Inspection ......6-15 How This Section is Organized ......6-3 Exhaust System Inspection ......6-15 Part A: Scheduled Maintenance Services ...6-4...
Page 436: Maintenance Schedule
Maintenance Schedule Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your Introduction vehicle in good working condition, but also helps the environment. Improper vehicle maintenance can Important: Keep engine oil at the proper level and even affect the quality of the air we breathe.
Page 437: How This Section Is Organized
How This Section is Organized “Part B: Owner Checks and Services” tells you what should be checked and when. It also explains what you can easily do to help keep your vehicle in good This maintenance schedule is divided into ﬁve parts: condition.
Page 438: Part A: Scheduled Maintenance Services
Part A: Scheduled Maintenance This part tells you the maintenance services you should have done and when to schedule them. Services When you go to your dealer for your service needs, you’ll know that GM-trained and supported service This part contains engine oil and chassis lubrication people will perform the work using GM parts.
Page 439: Scheduled Maintenance
Scheduled Maintenance Footnotes † The U.S. Environmental Protection Agency or the The services shown in this schedule up to 100,000 miles California Air Resources Board has determined that the (166 000 km) should be repeated after 100,000 miles failure to perform this maintenance item will not nullify (166 000 km) at the same intervals for the life of the emission warranty or limit recall liability prior to this vehicle.
Page 440 Engine Oil and Chassis Lubrication It is also important to check your oil regularly and keep it at the proper level. Scheduled Maintenance If the system is ever reset accidentally, you must Change engine oil and ﬁlter as indicated by the GM change your oil at 3,000 miles (5 000 km) since your Oil Life System (or every 12 months, whichever last oil change.
Page 441 7,500 Miles (12 500 km) Rotate tires. See Tire Inspection and Rotation on page 5-62 for proper rotation pattern and additional Rotate tires. See Tire Inspection and Rotation on information. (See footnote +.) page 5-62 for proper rotation pattern and additional Replace engine air cleaner ﬁlter.
Page 442 50,000 Miles (83 000 km) Rotate tires. See Tire Inspection and Rotation on page 5-62 for proper rotation pattern and additional Change automatic transaxle ﬂuid and ﬁlter if the information. (See footnote +.) vehicle is mainly driven under one or more of Replace engine air cleaner ﬁlter.
Page 443 82,500 Miles (137 500 km) Change automatic transaxle ﬂuid and ﬁlter if the vehicle is mainly driven under one or more of Rotate tires. See Tire Inspection and Rotation on these conditions: page 5-62 for proper rotation pattern and additional −...
Page 444: Engine Oil Level Check
Part B: Owner Checks and Services Engine Coolant Level Check ® Check the engine coolant level and add DEX-COOL Listed in this part are owner checks and services coolant mixture if necessary. See Engine Coolant which should be performed at the intervals speciﬁed to on page 5-23 for further details.
Page 445: At Least Twice A Year
At Least Twice a Year Spare Tire Check At least twice a year, after the monthly inﬂation check of Restraint System Check the spare tire determines that the spare is inﬂated to the correct tire inﬂation pressure, make sure that Make sure the safety belt reminder light and all your the spare tire is stored securely.
Page 446: At Least Once A Year
At Least Once a Year Starter Switch Check Key Lock Cylinders Service CAUTION: Lubricate the key lock cylinders with the lubricant speciﬁed in Part D. When you are doing this inspection, the Body Lubrication Service vehicle could move suddenly. If the vehicle moves, you or others could be injured.
Page 447: Ignition Transaxle Lock Check
Automatic Transaxle Shift Lock Control 2. Firmly apply the parking brake. See Parking Brake on page 2-38 if necessary. System Check Be ready to apply the regular brake immediately if the vehicle begins to move. 3. With the engine off, turn the key to the RUN CAUTION: position, but don’t start the engine.
Page 448: Underbody Flushing Service
Parking Brake and Automatic Transaxle Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the Park (P) Mechanism Check parking brake. • To check the parking brake’s holding ability: With the engine running and transaxle in NEUTRAL (N), CAUTION: slowly remove foot pressure from the regular...
Page 449: Part C: Periodic Maintenance Inspections
Part C: Periodic Steering, Suspension and Front Maintenance Inspections Drive Axle Boot and Seal Inspection Listed in this part are inspections and services which Inspect the front and rear suspension and steering should be performed at least twice a year (for instance, system for damaged, loose or missing parts, signs of each spring and fall).
Page 450: Fuel System Inspection
Fuel System Inspection All-Wheel Drive Inspection Inspect the complete fuel system for damage or leaks. Inspect the transfer case (power transfer unit) and carrier assembly-differential (rear drive module) every 12 months or at engine oil change intervals, check rear Engine Cooling System Inspection differential and transfer case and add lubricant when necessary.
Page 451: Part D: Recommended Fluids And Lubricants
Part D: Recommended Fluids and Usage Fluid/Lubricant Lubricants GM Power Steering Fluid (GM Part Power Steering No. U.S. 1052884, in Canada System 993294, or equivalent). Fluids and lubricants identiﬁed below by name, part ® Automatic DEXRON -III Automatic number or speciﬁcation may be obtained from your Transaxle Transmission Fluid.
Page 452 Usage Fluid/Lubricant Usage Fluid/Lubricant Hood Latch Lubriplate Lubricant Aerosol (GM Assembly, Lubriplate Lubricant Aerosol (GM Part No. U.S. 12346293, in Canada Sliding Door Secondary Part No. U.S. 12346293, in Canada 992723, or equivalent) or lubricant Track Latch, Pivots, 992723, or equivalent) or lubricant meeting requirements of NLGI #2, Spring Anchor meeting requirements of NLGI #2,...
Page 453: Part E: Maintenance Record
Part E: Maintenance Record After the scheduled services are performed, record the date, odometer reading and who performed the service and any additional information from “Owner Checks and Services” or “Periodic Maintenance” on the following record pages. Also, you should retain all maintenance receipts. Maintenance Record Odometer Date...
Page 454 Maintenance Record (cont’d) Odometer Date Serviced By Maintenance Record Reading 6-20...
Page 455 Maintenance Record (cont’d) Odometer Date Serviced By Maintenance Record Reading 6-21...
Page 456 Maintenance Record (cont’d) Odometer Date Serviced By Maintenance Record Reading 6-22...
Page 457: Customer Assistance Information
Section 7 Customer Assistance Information Customer Assistance Information ......7-2 Reporting Safety Defects ........7-9 Customer Satisfaction Procedure ......7-2 Reporting Safety Defects to the United States Online Owner Center ........7-3 Government ..........7-9 Customer Assistance for Text Telephone Reporting Safety Defects to the Canadian (TTY) Users ..........7-4 Government ..........7-10 Customer Assistance Offices ......7-4...
Page 458: Customer Assistance Information
Your satisfaction and goodwill are important to the windshield.) your dealer and to Chevrolet. Normally, any concerns with the sales transaction or the operation of your • Dealership name and location vehicle will be resolved by your dealer’s sales or service...
Page 459: Online Owner Center
Online Owner Center The BBB Auto Line Program is an out of court program administered by the Council of Better Business Bureaus to settle automotive disputes regarding vehicle The Owner Center is a resource for your GM ownership repairs or the interpretation of the New Vehicle needs.
Page 460: Customer Assistance For Text Telephone (Tty) Users
Chevrolet encourages customers to call the toll-free 1-800-263-3777 (English) number for assistance. If a U.S. customer wishes 1-800-263-7854 (French) to write to Chevrolet, the letter should be addressed to 1-800-263-3830 (For Text Telephone devices (TTYs)) Chevrolet’s Customer Assistance Center. Roadside Assistance: 1-800-268-6800 United States –...
Page 461: Gm Mobility Program For Persons With Disabilities
Overseas – Customer Assistance GM Mobility Program for Persons with Disabilities Please contact the local General Motors Business Unit. Mexico, Central America and This program, available to Caribbean Islands/Countries (Except qualiﬁed applicants, can reimburse you up to Puerto Rico and U.S. Virgin Islands) – $1,000 toward eligible Customer Assistance aftermarket driver or...
Page 462: Roadside Assistance Program
Chevrolet is excited to announce the Plus: establishment of the Chevrolet Roadside Assistance Center. As the owner of a 2003 Chevrolet, membership • FREE Non-Warranty Towing (to the closest dealer in Roadside Assistance is free. from a legal roadway) Roadside Assistance is available 24 hours a day, •...
Page 463: Canadian Roadside Assistance
Courtesy Transportation When roadside services are required, our advisors will explain any payment obligations that may be incurred Chevrolet has always exempliﬁed quality and value in for utilizing outside services. its offering of motor vehicles. To enhance your For prompt assistance when calling, please have the ownership experience, we and our participating dealers following available to give to the advisor;...
Page 464: Plan Ahead When Possible
Warranty service can generally be completed while you maximum of $30.00 per day supported by receipts. This wait. However, if you are unable to wait Chevrolet requires that you sign and complete a rental agreement helps minimize your inconvenience by providing several and meet state, local and rental vehicle provider transportation options.
Page 465: Reporting Safety Defects
Additional Program Information Reporting Safety Defects Courtesy Transportation is available during the Bumper-to-Bumper warranty coverage period, but it is Reporting Safety Defects to the not part of the New Vehicle Limited Warranty. A United States Government separate booklet entitled “Warranty and Owner Assistance Information”...
Page 466: Reporting Safety Defects To The Canadian Government
RETAIL SELL PRICE: $50.00 Please call us at 1-800-222-1020, or write: Service Bulletins Chevrolet Motor Division Chevrolet Customer Assistance Center Service Bulletins give technical service information P.O. Box 33170 needed to knowledgeably service General Motors cars Detroit, MI 48232-5170 and trucks.
Page 467: Current And Past Model Order Forms
Owner’s Information ORDER TOLL FREE: 1-800-551-4123 Monday-Friday 8:00 AM - 6:00 PM Owner publications are written speciﬁcally for owners Eastern Time and intended to provide basic operational information about the vehicle. The owner’s manual will include For Credit Card Orders Only the Maintenance Schedule for all models.
Page 468 NOTES 7-12...
Page 469 AM-FM Radio ..........3-62 AM ............. 3-104 Accessory Inﬂator ........... 5-68 Antenna, Fixed Mast ........3-105 Accessory Power Outlets ......... 3-24 Anti-lock Brake System (ABS) ......4-6 Adding Washer Fluid ........5-39 Anti-Lock Brake, System Warning Light ....3-42 Additional Program Information ......7-9 Appearance Care ..........
Page 470 Audio System(s) (cont.) Battery ............5-43 Fixed Mast Antenna ........3-105 Before Leaving on a Long Trip ......4-22 Radio with Cassette and CD ......3-72 Before You Drive ..........3-92 Radio with CD ..........3-65 Bench Seat, Split ..........1-8 Radio with Six-Disc CD ........
Page 471 Checking Engine Oil ........5-14 Checking Things Under the Hood ...... 5-10 California Fuel ..........5-5 Checking Your Restraint Systems ....1-103 Canada – Customer Assistance ......7-4 Check ............3-45 Canadian Owners ..........ii Engine Light ..........3-45 Canadian Roadside Assistance ......7-7 Chemical Paint Spotting ........
Page 472 Cleaning Glass Surfaces ........5-89 Control of a Vehicle .......... 4-5 Cleaning Interior Plastic Components ....5-89 Convenience Center ........2-58 Cleaning Leather ..........5-89 Convenience Net ..........2-57 Cleaning the Top of the Instrument Panel ... 5-89 Coolant ............3-44 Cleaning Tires ..........
Page 473 Driving on Grades ........... 4-42 Driving on Snow or Ice ........4-27 Daytime Running Lamps/Automatic Headlamp Driving Through Deep Standing Water ....4-19 System ............3-16 Driving Through Flowing Water ......4-19 Defensive Driving ..........4-2 Driving with a Trailer ........4-40 Defogging and Defrosting .........
Page 474 Electrical System (cont.) Entertainment System (cont.) Power Windows and Other Power Options ..5-96 Cleaning Your DVD Player ......3-105 Windshield Wiper Fuses ....... 5-96 DVD Distortion .......... 3-103 Emissions Inspection and Maintenance Entry Lighting ..........3-18 ® Programs ........... 3-48 Erasing HomeLink Buttons ......
Page 475 Folding or Reclining the Seatbacks ... 1-10, 1-17, 1-22 Garage Door Opener Compartment ....2-53 Folding the Seatback ........1-26 Garage Door Opener ........2-47 Following Distance .......... 4-41 Gasoline ............5-4 Footnotes ............6-5 Octane ............5-4 Front Reading Lamps ........3-19 Speciﬁcations ..........
Page 476 Hood ............5-10 If You’re Caught in a Blizzard ......4-28 Checking Things Under ........ 5-10 Ignition Positions ..........2-31 Release ............. 5-10 Ignition Transaxle Lock Check ......6-13 Horn ............... 3-7 Infants and Young Children, Restraints ....1-58 How the System Works ........3-23 Inﬂation -- Tire Pressure ........
Page 477 Leaving Your Vehicle ........2-13 Liftgate ............2-22 Jump Starting ..........5-44 Lighted Vanity Mirror ........2-26 Light ............. 3-40 Air Bag Readiness ........3-40 Anti-Lock Brake System Warning ....3-42 Brake System Warning ......... 3-41 Key Lock Cylinders Service ......6-12 Malfunction Indicator ........
Page 478 Maintenance Schedule (cont.) Using Your ........... 6-4 Maintenance, Normal Replacement Parts ..5-104 Your Vehicle and the Environment ....6-2 Maintenance Schedule ........6-10 Maintenance When Trailer Towing ..... 4-43 At Each Fuel Fill ......... 6-10 Making Turns ..........4-41 At Least Once a Month ........
Page 479 Mirrors ............2-44 Outside ............2-45 Manual Rearview Mirror ........ 2-44 Convex Mirror ..........2-45 Outside Convex Mirror ......... 2-45 Heated Mirrors ..........2-45 Outside Heated Mirrors ........ 2-45 Power Mirrors ..........2-44 Outside Power Mirrors ........2-44 Overhead Console Switchbank ......3-21 MyGMLink.com ..........
Page 480 Passenger Compartment Air Filter ..... 3-33 Programming Mode ......... 2-62 Passing ..........4-13, 4-41 Entering ............. 2-62 ® PASS-Key III Operation ........2-29 Exiting ............2-70 ® PASS-Key III Security Message ....... 3-56 Programming the HomeLink Transmitter ..... 2-48 ® PASS-Key III ..........
Page 481 Radios (cont.) Removing the Flat Tire and Installing the Theft-Deterrent .......... 3-103 Spare Tire ..........5-77 Understanding Reception ......3-104 Removing the Spare Tire and Tools ....5-72 RDS Messages ......3-68, 3-76, 3-86 Removing the Split Bench Seat ......1-11 Rear Climate Control System ....
Page 482 Retro-Active Reset .......... 3-39 Scheduled Maintenance ........6-5 Right Front Passenger Position, Safety Belts ..1-45 Seat ............... 1-6 Roadside ............7-6 Head Restraints ..........1-6 Assistance Program ........7-6 Seats ............1-15 Rocking Your Vehicle To Get It Out ....4-31 Bucket Seats, Rear ........
Page 483 Service (cont.) Split Bench Seats ..........1-8 Doing Your Own Work ........5-3 Starter Switch Check ........6-12 Engine Soon Light ........3-45 Starting Your Engine ........2-32 Publications Ordering Information ....7-10 Steering in Emergencies ........4-11 Traction System Warning Message ....3-50 Steering, Suspension and Front Drive Axle Setting Preset PTYs ........
Page 484 Total Weight on Your Vehicle’s Tires ....4-38 Towing ............4-32 Tachometer ............ 3-39 Recreational Vehicle ........4-32 Taillamps ............5-56 Towing a Trailer .......... 4-36 Turn Signal, Stoplamps and Back-up Lamps ..5-56 Your Vehicle ..........4-32 TCS Warning Light .......... 3-43 Traction ............
Page 485 Understanding Radio Reception ....... 3-104 Vehicle (cont.) Uniform Tire Quality Grading ......5-65 Loading ............4-34 United States – Customer Assistance ....7-4 Symbols ............iv Used Replacement Wheels ......5-67 Ventilation Adjustment ........3-28 Using Cleaner on Fabric ........5-88 Video Screen ..........
Page 486 Wheels (cont.) Windows (cont.) When to Add Engine Oil ........5-15 Power ............2-25 When to Change Engine Oil Side Window Latches ........2-25 (GM Oil Life System) ........5-17 Windshield Washer Fluid Level Check ....6-10 When to Check and Change Automatic Windshield Washer .........

Chevrolet Venture 2003 Owner's Manual

Section 1 Seats and Restraint Systems

Seats and Restraint Systems

Air Bag Systems

Restraint System Check

Section 2 Features and Controls

Features and Controls

Keys

Doors and Locks

Windows

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

Onstar System

Homelink Transmitter

Storage Areas

Section 3 Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages and Indicators

Message Center

Driver Information Center (DIC)

Audio System(S)

Section 4 Driving Your Vehicle

Driving Your Vehicle

Your Driving, the Road, and Your Vehicle

Towing

Quick Links

Chapters

Related Manuals for Chevrolet Venture 2003

Summary of Contents for Chevrolet Venture 2003