Sony CDX-GT620U Operating Instructions Manual page 23

SONY;
3-275-495-71 (1)
6
A
FM/AM
Compact Disc Player
Installation/Connections
Instalaci6n/Conexiones
-
B
SUB OUT (MONO)
CDX-GT620U
© 2008 Sony Corporation Printed in Thailand
I I I
Connectioll example
I])
Connection diagram []]
Notes (fJ-8)
• Be sure to connecf the ground (earth) lead before connecting
the amplifier
• The alarm will only sound if the built-m amplifier is used.
o
To a metal surface of the car
First connect the black ground (earth) lead. then connect the
yellow and red power supply leads
e
To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
Notes
• It is nol necessary to connect this lead if there is no power
antenna (aeriat) or antenna (aerial) booster. or with a
manually-operated telescopic antenna (aerial).
• When your car has a built-in FM/AM antenna (aeriat)
In
the rear/side glass. see '"Notes on the control and power
supply leads"
e
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecling any other
system may damage the uni/.
o
To the interface cable of a car telephone
(3 To a car's illumination signal
Be sure to connect Ihe black ground (earth) lead to a metal
surface of the car firs/.
o
To the +12 V power terminal which is
energized in the accessory position of the
ignition switch
Notes
• If Ihere is no accessory position. connect to the ~ 12 V
power (battery) terminal which
IS
energized at all times
Be sure to connect the black ground (earth) lead to a
metal surface of the car first.
• When your car has
a
built-in FM/AM anlenna (aerial) in
the rear/side glass. see "Notes on the control and power
supply leads."
8
To the +12V power terminal which is
energized at all times
Be sure to connect the black ground (earth) lead to a metal
surface of the car first
Catch
Parts list
rn // ,
• The numbers in the list arc keyed to those in the
instructions
• The bracket
CD
and the protection collar
0
arc
attached to the unit hcfore shipping. Before mounting
the unit. usc the release keys
@
to remove the bracket
CD
from the unit. ror details. sec "Removing the
protection collar and the bracket (Elf' on the reverse
sidl": of the sheet.
• Keep the release keys
@
for future use as they
are also necessary if you remove the unit from
your car.
Caution
Handle the bracket
G)
carefully to avoid injuring your
fingers
lC8l1tions -
• This unit is designed for negative ground (earth) 12 V
DC
operation
only
• Do not gCllhc leads under ,\ screw. or caught in moving
paris (c.g. scal r<lilingl.
• Before making connct",iolls. [urn the car ignition off to
avoid short circuits.
• Connect the yellow and red power supply leads only
:!fter all other le'lds have been connected
• Run all ground (earth) leads to a common
ground (earth) point.
• Be sure to insulate any loose um.:onnectcd leads witn
electrical tape for safety.
• The usc of opti('al instrumcnts wilh this product will
increa.-;eeye hazard.
Notes on the power supply lead (yellow)
• When connccting this unit in combination with other
~tereo components, the connected car circuit's rating
must he nigher than the sum of ca("h component"s fuse.
• When no car circuits arc rated high enough. conneCl
Ihe unit directly to the ballery
x 2
Power amplifier
Amplificador de palencia
Rotary commander RM-X4S
Manda rotatorio RM·X4S
x4
®
Front speaker
Altavoz frontal
Rear speaker
Altavoz posterior
Equipment used in illustrations (not supplied)
Equipo utilizado en las ilustraciones (no suministrado)
D
Active subwoofer
AltavQz potenciador de
graves activo
Note
Before installing. make sure that the catches on both sides of
the bracketeD are bent inwards 2 mm
('/32
in), If the catches are
straight or bent outwards. the unit will not be installed securely
and may spring out