Turning Power On And Off; Raising The Monitor; Lowering The Monitor; Selecting The Monitor's Opening Position - Alpine CVA-1014 Owner's Manual

Turning Power On and Off

Some of this unit's functions, cannot be performed
while the vehicle is in motion. Be sure to stop your
vehicle in a safe location and apply the parking
brake, before attempting these operations.
1
Press SOURCE/POWER to turn on the unit.
The opening screen appears automatically on
the monitor.
NOTE
The unit can be turned on by pressing any other button
except the OPEN/CLOSE, TITLE
The volume level gradually increases to the
previous level you were listening to before the
unit was turned off. Press and hold SOURCE/
POWER for at least 2 seconds to turn off the
unit.
NOTES
• After turning the system off, a slight ghost of the image
will remain temporarily. This is an effect peculiar to
LCD technology and is normal.
• Under cold temperature conditions, the screen may
lose contrast temporarily. After a short warm-up
period, it will return to normal.
• The CVA-1014 draws minimal current even when its
power switch is turned off. If the switched power
(ignition) lead of the CVA-1014 is connected directly
to the positive (+) post of the vehicle's battery, the
battery may be discharged. If this lead is unswitched,
it must be disconnected from the battery post should
the vehicle be left unused for an extended period of
time.
An SPST (Single-Pole, Single-Throw) switch (sold
separately) can be added to simplify this procedure.
Then, you can simply place it in the OFF position
when you leave the vehicle. Turn the SPST switch back
ON before using the CVA-1014. For connecting the
SPST switch, refer to "Connection Diagram of SPST
Switch" on page 51.
• Some operation of the unit cannot be performed while
the vehicle is in motion. In this case, be sure to first
stop your vehicle and apply the parking brake, then
perform the operation.

Raising the Monitor

1
Press OPEN/CLOSE, or press and hold MUTE
on the optional Remote Control.
The unit beeps 3 times and raises the monitor
automatically.
NOTES
• The CVA-1014 is a precision device. With gentle
• If the monitor touches an obstacle while it is being
• When the movable monitor is opened, do not place any
and TILT 7 8 .
• Under low ambient temperature conditions, the
• For your safety, some operation of the unit cannot be
• If you select AUX or NAVI as the current source

Lowering the Monitor

1
Press OPEN/CLOSE, or press and hold MUTE
on the optional Remote Control.
The unit will beep 3 times and lower the monitor
automatically.
NOTES
• The CVA-1014 is a precision device. With gentle
• If the monitor touches an obstacle while it is being
• If you select AUX or NAVI as the current source
Selecting the Monitor's Opening
Position
The monitor's opening position has 2 settings.
1
Press and hold OPEN/CLOSE for at least 2
seconds while the monitor is being raised. Each
press changes the monitor position back or forth.
Basic Operation
handling, its unique capabilities can be enjoyed for a
long time.
raised, the unit will stop raising the monitor
immediately. Should this occur, remove the obstacle
and press OPEN/CLOSE again to raise the monitor.
object on the monitor and be careful not to bump or
apply any pressure to the monitor while it is open. This
can cause damage to the mechanism.
display may be dark for a short period of time
immediately after the power is turned on. Once the
LCD has warmed up, the display will return to
normal.
performed while the vehicle is in motion. In this case,
first stop the vehicle and engage the parking brake,
then perform the operation.
without connecting to the CVA-1014, a noise may
occur when you open the monitor. This is not a
malfunction.
handling, its unique capabilities can be enjoyed for a
long time.
lowered, the unit will stop lowering the monitor
immediately.
Should this occur, remove the obstacle and press
OPEN/CLOSE again to lower the monitor.
without connecting to the CVA-1014, a noise may
occur when you close the monitor. This is not a
malfunction.
7
-EN