Programmed Cooking; The Programmer - Indesit FM 70 P.1 MR Instructions For Installation And Use Manual

Programmer knob
to display a symbol,
turn the knob
to select a symbol,
press the knob
to set the various display,
setting the clock and timer,
total cooking time and
end time
Turn the knob
The "24 hour" electronic programmer enables the user to
set the duration and end time of a cooking operation for
any time within the upcoming 24 hours.
You can check the end time
and the timer simply by turning the programmer knob
to select the corresponding symbol.
• Setting the clock:
When the appliance is turned on for the first time or after
a power cutoff, the clock display and the
light are flashing. Turn the programmer knob until the
desired time is shown. After 3 seconds, the time is vali-
dated.
To modify the time, the oven must be in manual mode
(no indicator lights on). Press and hold the programmer
knob until the indicator light starts flashing. Then
turn the knob to display the desired time.
1 - Immediate start
The oven starts heating immediately and stops automati-
cally at the end of the programmed time.
- Display the cooking time:
Turn the programmer knob to select the
Press the knob. flashes. Turn the knob to display the
desired cooking time. After 3 seconds, your choice is vali-
dated. remains on at half power.
(Ignore the flashing of the
- Set the Function Selector to the desired position
- If desired, change the temperature using the Temperature
Selector.
• To cancel the cooking time, select the
and turn the programmer knob to display 0.00.
• When the time is up, an audio signal sounds. To turn off the
signal, press the knob and set the Function Selector back to
"0".

The programmer

Clock :
The time of day is always shown
also used to temporarily show the
end of time of an operation
for increasing
numbers
for decreasing
numbers
, the cooking time
indicator

Programmed cooking

indicator light.
light.)
function. Press
Symbol
is used to set the
end time for a cooking
or pyrolysis operation
Symbol
is used to set the total
cooking or pyrolysis
time (duration)
Symbol
Symbol
is used for operating is used to set the clock
the audio timer
• Audio timer:
To use the audio signal timer built into your oven, display
the (hourglass) symbol by turning and pressing the
programmer knob. Then turn until the desired time is dis-
played. As soon as you release the knob, the timer will
start to count down. When the time is up, an audio signal
sounds. Press the knob to turn off the signal. The timer
operates independently from the oven.
Cooking without the Programmer (manual mode)
When no symbol is lit, the oven is in manual mode.
- Use the Function Selector to choose the desired cook-
ing method. A preselected temperature appears. You
can change it using the Temperature Selector.
The indicator light flashes slowly while the
temperature in the oven is rising. It stays on when the
temperature reaches the specified level.
When the cooking is done, remember to turn off the oven
by setting the Function Selector back to "0".
2 - Delayed start
The programmer automatically starts the oven at the
programmed time.
- Make sure that the clock is set to the right time
- To display the cooking time:
Select the indicator light, then press the knob.
Turn the knob to select the desired cooking time, such as 1:30
for example.
The indicator light flashes. Turn the knob to select the end
time for the cooking operation (12:30, for example). Your choice
is validated after 3 seconds.
The two indicator lights
- Set the Function Selector to the desired position.
- If desired, change the temperature using the Temperature
Selector.
At 11:00, the cooking starts.
- To change the end time, proceed as follows:
Select the indicator light. Press the knob.
Select the desired end time (for example, 12:30). After 3 sec-
onds, the time of day reappears.
• When the time is up, an audio signal sounds. To turn off the
signal, press the knob and set the Function Selector back to "0".
7
flashes.
and remain on at half power.
flashes.
GB