Table of Contents
Advertisement
VIII.
PROGRAMMING WORKSHEETS
LOC
PG
0
7
SCAN FUNCTIONS
Seg 1
Seg 2
Seg 3
8
RESERVED
1-240
241
8
X-10 ADDRESS
Seg 1
Seg 2
Seg 3
8
Seg 4
Seg 5
8
OPTIONS AND READER PARTITION
242
Seg 1
Seg 2
12
DESCRIPTION
SINGLE SCAN FUNCTION (1 Beep)
1 = "On" to send Code Entry function to the control panel.
2 = "On" to activate the Armed Away mode.
3 = "On" to activate the Armed Stay mode.
4 = "On" to send the Disarm function to the control panel.
5 = "On" to send Auxiliary Function #1 to the control panel.
6 = "On" to send Auxiliary Function #2 to the control panel.
7 = "On" to broadcast an X-10 function (Loc 241 for programming).
8 = "On" to send an RTE; and activate the onboard open collector output.
DOUBLE SCAN FUNCTION (2 Beep)
1 = "On" to send Code Entry function to the control panel.
2 = "On" to activate the Armed Away mode.
3 = "On" to activate the Armed Stay mode.
4 = "On" to send the Disarm function to the control panel.
5 = "On" to send Auxiliary Function #1 to the control panel.
6 = "On" to send Auxiliary Function #2 to the control panel.
7 = "On" to broadcast an X-10 function (Loc 241 for programming).
8 = "On" to send an RTE; and activate the onboard open collector output.
SINGLE SCAN HOLD FUNCTION (3 Beep)
1 = "On" to send Code Entry function to the control panel.
2 = "On" to activate the Armed Away mode.
3 = "On" to activate the Armed Stay mode.
4 = "On" to send the Disarm function to the control panel.
5 = "On" to send Auxiliary Function #1 to the control panel.
6 = "On" to send Auxiliary Function #2 to the control panel.
7 = "On" to broadcast an X-10 function (Loc 241 for programming).
8 = "On" to send an RTE; and activate the onboard open collector output.
MODULE NUMBER
HOUSE CODE
X-10 ADDRESS CODES
(see chart)
0=A
4=E
1=B
5=F
2=C
6=G
3=D
7=H
SINGLE SCAN FUNCTION (1Beep)
0 = All units off
1 = All lights on
2 = On
3 = Off
DOUBLE SCAN FUNCTION (2 Beep)
0 = All units off
1 = All lights on
2 = On
3 = Off
SINGLE SCAN HOLD FUNCTION (3 Beep)
0 = All units off
1 = All lights on
2 = On
3 = Off
SYSTEM OPTIONS
1 = "On" if enabled for User Card Programming
2 = "On" if optical tamper enabled
3 = "On" if buzzer follows keypad buzzing
4 = "On" if ding-dong chime enabled (Opt 3 & chime must be enabled)
5 = "On" if an RTE from a scanned card is to be logged as Code Entry
6 = "On" if reader is in NX-1700E Legacy Mode
7 = "On" if an RTE from a zone or the Egress input is to be logged as Code Entry.
8 = "On" if LED extinguish after 2 minutes without a scan.
LED1 (GREEN) OPTIONS
1 = "On" follows system Ready status
2 = "On" to toggle with the Open Collector output
3 = "On" if inverted
4 = 4-8= Reserved.
8=I
12=M
9=J
13=N
10=K
14=O
11=L
15=P
4 = Dim
5 = Bright
6 = All lights off
4 = Dim
5 = Bright
6 = All lights off
4 = Dim
5 = Bright
6 = All lights off
IMPORTANT TIP:
Defaults are shown in bold italics.
DEFAULT
YOUR DATA
8
1
1
0
0
2
3
2
3, 5, 6
1,2
NX-1700E Card Reader
Advertisement
Table of Contents
