Table of Contents
Advertisement
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
TR-2
Retain This
Manual for
Reference
09-14-04
V4
OWNER'S
MANUAL
TECH ROD GYM
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
TR-2
IMPEX INC.
Advertisement
Table of Contents
Related Manuals for Impex TR-2
Summary of Contents for Impex TR-2
- Page 1 Table of Contents Safety Notice Hardware Identifier Assembly Instruction Parts List Warranty Ordering Parts Model TR-2 Retain This Manual for Reference 09-14-04 OWNER'S MANUAL TECH ROD GYM IMPEX INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com...
- Page 2 WARNING LABELS PLACEMENT The Warning Labels shown here have been placed on Lower Pulley Support Base. If this Labels are missing or illegible, please call Customer Service at 1-800-999- 8899 for free replacement. Apply the Label in the location shown.
-
Page 3: Table Of Contents
WARRANTY...… 20 ORDERING PARTS... 20 BEFORE YOU BEGIN Thank you for selecting the TECH ROD GYM TR-2 by IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction. -
Page 4: Important Safety Notices
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. -
Page 5: Hardware Pack
HARDWARE PACK... -
Page 6: Assembly Instructions
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Place the Base Platform (#8) on flat surface. Attach the Vertical Frame (#1) to the open bracket on the Base Platform. - Page 7 STEP 2 (See Diagram 2) A.) Attach the lower Rear Support Frame (#2) to the Base Platform (#8). Secure it with one M10 x 4 7/8” Hex Bolt (#13), Ø ¾” Washer (#10), and M10 Aircraft Nut (#16). DO NOT tighten the Nut and Bolt yet.
- Page 8 STEP 3 (See Diagram 3) A.) Attach the High Pulley Support Bar (#18) to the Upper Frame (#17). Securely tighten with one Bracket (#19), two M10 x 2 3/8” Hex Bolts (#20) and two ؾ” Washers (#10). Cover the two Hex Bolts with two M10 Nut Caps (#21). B.) Attach the Upper Frame (#17) to the Vertical Frame (#1).
- Page 9 STEP 4 (See Diagram 4) A.) Attach the Tech Rod Set (#24) to the Rear Support Frame (#2). Secure it with four Ø 1/4” x ¾” Philips Screws (#25). B.) Slide the Tech Rod Organizer (#23) onto the top of the Rods to hold each Rod in position.
- Page 10 STEP 5 (See Diagram 5) A.) Place the Seat Pad (#27) onto the Seat Support (#26). Secure it with four M6 x ¾” Hex Bolts (#6) and ؽ” Washers (#7). B.) Attach the Seat Support (#26) to the open bracket on the Vertical Frame (#1). Use a Lock Knob (#28) to securely lock the Seat Support in position.
- Page 11 STEP 6 (See Diagram 6) A.) Attach the Leg Developer (#30) to the front of Seat Support (#26). Secure it with one M10 x 3” Hex Bolt (#12), two ؾ” Washers (#10), and one M10 Aircraft Nut (#16). B.) Cover the Nut and Bolt with two M10 Nut Caps (#21). Cover the Nuts on the Cable Roller (#44) with two M8 Nut Caps (#29).
- Page 12 STEP 7 (See Diagram 7) A.) Insert a Foam Tube (#32) halfway through the hole on the Seat Support (#26). Insert a Foam Tube halfway through the hole on the Leg Developer (#30). B.) Push four Foam Rolls (#33) onto the Foam Tubes from both ends. Plug four Foam Roll End Caps (#34) into the ends of the Tubes.
- Page 13 STEP 8 (See Diagram 8 & Lat Bar Cable Loop Diagram) A.) Follow the below instructions to use the Lat Bar. B.) Attach a Tech Rod Cable (#11) to the Right Pulley on the Extension Tube (#43). Attach the other end, L Shaped Connector (#41) to one of the Tech Rod. C.) Attach one 57”...
- Page 14 LAT BAR CABLE LOOP DIAGRAM...
- Page 15 STEP 9 (See Diagram 9 & Leg Developer Cable Loop Diagram) A.) Follow the below instructions to use the Leg Developer. B.) Detach the end of the Lat Bar Cables from the End Hooks on Tech Rod Cables and hook the Cable ends onto the Cable Hangers on the side of the Vertical Frame. C.) Store the Lat Bar onto the Lat Bar Holders (#39) on the side of the Vertical Frame.
- Page 16 LEG DEVELOPER CABLE LOOP DIAGRAM...
- Page 17 STEP 10 (See Diagram10 & Cable Loop Diagram) A.) Follow the below instructions when doing bench press or butterfly exercises. B.) Attach the ends of Lat Bar Cables (#35) and Leg Developer Cables (#36) onto the Cable Hangers (#42) on the side of the Vertical Frame. C.) Connect the two Hand Straps (#38) to the Tech Rod Cables (#11) for various exercises.
- Page 18 TECH ROD CABLE LOOP DIAGRAM...
-
Page 19: Exploded Diagram
EXPLODED DIAGRAM... -
Page 20: Resistance Chart
TECH ROD RESISTANCE CHART TECH ROD (each side) 10LB 10LB 25LB 50LB TOTAL *Numbers are approximate. Actual resistance may vary. *Value is for each cable. Bench Press/ Butterfly 5 LB 10 LB 10 LB 25 LB 50 LB 100LB LEG DEVELOPER CABLE CABLE 5 LB... -
Page 21: Parts List
PARTS LIST KEY NO. DESCRIPTION Vertical Frame Rear Support Frame M8 x 5/8” Allen Bolt Ø 5/8” Washer Back Pad M6 x ¾” Hex Bolt Ø ½” Washer Base Platform M10 x 5/8” Allen Bolt Ø ¾” Washer Tech Rod Cable M10 x 3”... -
Page 22: Warranty
IMPEX. IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential damages or whatsoever natures.