APR/15/2002 OPERATION: A. REGULAR TRANSMITTER OPERATION: Transmitter System Function Remark Button Lock Doors & Arm System Arm and Noiseless mode Press within 3 seconds. Arm and Delete The Zone 1 / Shock Sensor Press twice within 3 seconds. Arm and Delete The Zone 4 / Optional Sensor Press third time within 6 seconds.
Page 3
APR/15/2002 Second Vehicle Transmitter Programming: (Random code transmitter does not have this feature) Your 8-button remote transmitter can be utilized to control a second vehicle security system, To program the remote control transmitter to a second vehicle, follow the instructions for Transmitter programming. All programming parameters be the same except for the following: 1.
APR/15/2002 Activate Remote Start Press and Hold for 1 seconds (1 second) Channel 2 (trunk) Timer control Press and Hold for 2 seconds (2-second) Passive Arming By-pass While the System Disarmed. Turn Off The Remote Start C. LED display: Function Function Disarmed 1 flashes...
APR/15/2002 Press the button within 3 seconds: The siren chirps once again, the system is now in Noiseless mode, On this mode trigger the zone 1 shock sensor or zone 4 optional sensor the trigger timer will reduced from 60 seconds to 15 seconds. . The noiseless feature is programmed to activate for one arming cycle only.
APR/15/2002 2. The siren will chirp twice and parking light will flash twice to indicating that the security system is now disarmed. The vehicle doors will unlock and dome light wills turns on for 30 seconds upon disarming when interfaced with the security system. System Disarm Doors Trigger Trunk/Hood Trigger...
APR/15/2002 3. Within 15 seconds of the last entered 10ths digit, turn the Ignition Switch “Off” then “ON”. 4. Within 15 seconds, Press and Release the Valet Switch 3 times 5. Turn the Ignition Switch to “Off” position. [4] Chirps form siren/horn, [3] flash from parking light to indicate the system was disarmed. K.
APR/15/2002 Ignition Trigger Activate PIR Sensor NOISE ABATEMENT CIRCUIT: You system has “Noise Abatement Circuit”. It prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental condition such as thunder, jackhammers airport noise, etc. Here’s how “Noise Abatement Circuit” works: The alarm triggers five times. Each time, the same sensor or switch is triggering the alarm.
APR/15/2002 Q. IGNITION CONTROL DOOR LOCKS. II – 2 (See Alarm Feature Programming). If the vehicles door locks have been interfaced to the security system, the system will automatically lock the vehicle's doors when the ignition is turned “ON” and /or unlock the vehicle’s doors when the ignition is turned “OFF”.
APR/15/2002 REMOTE START OPERATION: WARNINGS: As with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of. 1. Keep the transmitter out of children’s reach. 2. Do not leave anyone in the vehicle while running on remote control. 3.
APR/15/2002 3.The engine will run until the pre-programmed time elapsed or shutdown input is received. E. TIMER / TEMPERATURE START: This unit can be programmed to start and run the engine every 3 or 24 hours. The engine will run for the programmed run time and then shut down.
APR/15/2002 7. The vehicle refused to start running after {3} unsuccessful attempts. H. DISABLING THE REMOTE START SYSTEM: (If installed) This feature allows your system’s remote start unit to be temporarily disabled to prevent the vehicle from being remote started accidentally. This feature is useful if the vehicle is being serviced or stored in an enclosed area.
APR/15/2002 Temperature Sensor (Optional) The temperature sensor which takes the temperature of the passenger compartment to display on the LCD screen of the Remote Control. Battery replacement A 1.5V type AAA Alkaline battery powers the Remote Transmitter. When the power of the battery weakens icon shall be displayed on the LCD screen.
APR/15/2002 Time Monitor Alert Alarm Time indicator of your vehicle You have set morning call alarm Temperature Monitor Count Down Timer Indoor temperature of your vehicle Reminder when time is up for parking Vibration Mode Mute Chirp Sound Remote Control vibrates when the Operating silent when the icon is system is triggered emitted...
APR/15/2002 3. Press for real time indication when the timer is counting down. 4. ALERT ALARM SETTING (ON/OFF) Press button simultaneously , the LCD screen will show icon and alarm time (ie 12:00) to turn on the alert alarm. Press button simultaneously again, the icon will disappear to turn off the alert alarm.
Page 16
APR/15/2002 7. Press for Off and for On the alert alarm at PM6:30. 3. COUNT DOWN TIMER SETTING: Example set count down timer at 2:30 1.Press once for 4 seconds. 2.Press 5 times then the hour digit flashes. 3.Press to decrease or increase the hours digit until 2:xx 4.Press once again then the minutes digit flashes.