JAN/07/2003 TABLE OF CONTENTS: A. REMOTE TRANSMITTER OPERATION ………………………………………….…………………….………. B. BUTTON LOCK …………………………………………………..……………………………………….……..…. C. LED DISPLAY .……………..………………………………………………………………………….……………. D. CHIRP INDICATOR ..………..…………………………………………………………………………………..…. E. PARKING LIGHT …….……..………………………………………………………………………………..….…. F. ALARM OPERATION CONDITION .…………………………………………………………………………...…. G. ACTIVE ARMING – ARM & LOCK .………………………………………………………………...……………. Defective Sensor Reminder Silent Arming / Disarming Shock Sensor By-Pass H.
Page 3
JAN/07/2003 T. IGNITION CONTROL THE DOOR LOCK/UNLOCK. ………..………………….…………………………..…..9 TRUNK RELEASE (CHANNEL OUTPUT ………..………………………………………………………..…10 CHANNEL TIMER CONTROL OUTPUT ………..………………………………………………..…..……….10 W. CHANNEL 5 TIMER CONTROL OUTPUT ………..…………………………………………….….….……... 10 X. CHANNEL 6 TIMER CONTROL OUTPUT ………..…………………………………………….…….…….…. Y. POWER ON MEMONRY: ………..………………………………………………………………….…….…..…. REMOTE START OPERATION: A.
JAN/07/2003 7. Should the unit malfunction, disconnect the fuse until the problem is corrected. 8. The use and operations of this system is the sole responsibility of the operator. 9. Some areas may have local ordinances that prohibit leaving a vehicle running on public streets. 10.
JAN/07/2003 LCD DISPLAY TRANSMITTER OPERATION ONLY: Transmitter Button System Function Remark System’s Trigger Record Check Press within 3 seconds System’s Status Check Press within 3 seconds Button Lock Press within 3 seconds and Hold button for 2 seconds Optional Driving Pager Press within 3 seconds Monitor Indoor Temperature Press within 3 seconds...
JAN/07/2003 Shock Sensor Trigger Ignition Trigger Clear The Flash Icon: Press the button 3 times within 3 seconds will clear the flash icon on the LCD screen transmitter. TAMPER DISARMING: If alarm triggered, upon disarm the system, siren chirp 4 times, parking light flash 3 times.
JAN/07/2003 function and remote start function are bypassed, however the remote panic feature and remote door locks will remain operational. To use the valet mode, the system must first be disarmed either by using you remote transmitter, or by operating the Manual override sequence. Enter Valet Mode: Remote Door Lock Remote Door Unlock...
JAN/07/2003 NOISE ABATEMENT CIRCUIT: You system has “Noise Abatement Circuit”. It prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental condition such as thunder, jackhammers airport noise, etc. Here’s how “Noise Abatement Circuit” works: The alarm triggers five times. Each time, the same sensor or switch is triggering the alarm.
JAN/07/2003 Indoor Driving Paging Under the ignition switch “off” condition, press and hold the valet switch for 2 seconds to page the driver, one chirp sound shall be emitted from the vehicle and the paging melody sound continues sounding from you Remote LCD Transmitter and “...
JAN/07/2003 REMOTE START OPERATION: A. TO REMOTE START THE VEHICLE: When you want to start your vehicle, Activate Remote Start 1. Press button twice on the transmitter. 2. The parking light will activate to indicate the remote start received the signal. 3.
JAN/07/2003 2. Immediately depress the button once, within 2 seconds 3-a. 3 Hours Timer Start: Rapidly depresses the button. (or depresses buttons, if you program buttons = Start / Stop button.) The parking light will flash (3) times. The siren or horn chirps (3) times.
JAN/07/2003 H. DISABLING THE REMOTE START SYSTEM: (If installed) This feature allows your system’s remote start unit to be temporarily disabled to prevent the vehicle from being remote started accidentally. This feature is useful if the vehicle is being serviced or stored in an enclosed area.
JAN/07/2003 A. BATTERY REPLACEMENT: A 1.5V type AAA Alkaline battery powers the Remote Transmitter. When the power of the battery weakens a icon shall be displayed on the LCD screen. When the old battery is replaced to new one, there will be beep sounds indicate the power is up and the clock on the LCD screen returns to AM12:00 after displaying all the icons.
JAN/07/2003 (Bi) Enable / Disable Bi Sound While (2-second) Pressing Button 1. Screen Lamp ON: Press and hold the button one second, with one melody sound and the LCD screen lamp will turns on for 5 seconds 2. Power Save Mode: While the power save mode, the LCD remote transmitter uses “0” current to save the battery power.
JAN/07/2003 Transmitter Button Description Press Transmitter Button – Timer Setting (Hour) Press & Hold the *Flash digit for adjusting button for 3 seconds – Time setting (Minute) Press the button once *Flash digit for adjusting Alert Alarm Time Setting (Hour) –...
JAN/07/2003 7. Press the button to start the count down timer, and the “ON” icon will show on the LCD screen. Press the button to stop the count down timer, and the “OFF” icon will show on the LCD screen. 8.