Hanging The Fan; Installing The Blade Irons; Wiring The Fan - Hunter Ceiling fans Installation And Operation Manual

6 6 6 6 6
2. Remove the hook from the assembly.
3. Completely remove the set screw (identified in Figure 12) from
the fan adapter.
4. Put the set screw, previously removed, through the two black
neoprene washers and the hook as shown in Figure 14. Hook
must be installed in same orientation as shown in Figure 14.
Black Neoprene
Washer
F F F F F i i i i i g g g g g ur ur ur ur ure 14 - A e 14 - A e 14 - A e 14 - A e 14 - As s s s s s s s s s e e e e e mb mblin mb mb mb lin ling t lin lin
a a a a a s s s s s s s s s s e e e e e mb
5. Reassemble the set screw to the adapter as shown in Figure 14.
NOTE: The rubber washers should be tight enough to keep
the hook standing straight up, but the set screw should not be
completely tighten as to keep the hook from being able to
swing.
6. Place the canopy trim ring then the canopy over the adapter
as shown in Figure 15.
7. Place the low profile washer (lip up) into the canopy as shown
in Figure 15 fitting the notch in the low profile washer over the
adapter set screw and hook.
Tab Hole
F F F F F i i i i i g g g g g ur ur ur ur ure 15 - A e 15 - A e 15 - As s s s s s s s s s e e e e e mb e 15 - A mb mblin mb lin ling c lin lin g c g ca a a a a n n n n n o o o o o p p p p p y f y f y f y f y fo o o o o r l r l r l r l r lo o o o o w p g c
e 15 - A mb g c
8. Rotate the canopy until the arrow on the low profile washer
aligns with the tab hole on the canopy as shown in Figure 15.
9. Align the holes in the low profile washer with the holes in the
adapter and assemble securely with the three #8-32 x 1" screws.

installing the blade irons

1. Turn the fan upside down. Use the ceiling fan package to sup-
port the fan while assembling the blade irons.
2. Loosen all of the blade iron assembly screws. Do not com-
pletely remove the screws.
3. Remove and discard all of the shipping blocks.
4. Slide the blade iron under the switch housing plate aligning
the two notches with the two blade iron assembly screws as
shown in Figure 16.
5. Pull the blade iron forward under the loosened blade iron as-
sembly screws to fully engage the blade iron.
41822-01 10/22/2003
Hook
Set Screw
g t g th h h h h e s g t g t e s e s e s e se e e e e t s t s t s t s t sc c c c c r r r r r e e e e e w f w fo o o o o r l r l r l r l r lo o o o o w p w f w f w f w p w p w pr r r r r o o o o o f f f f f il il il il ile e e e e w p
mb mb mbl l l l l y y y y y
mb
Low Profile Washer
Canopy
Canopy Trim Ring
Arrow on the
Low Profile
Washer
w p w p w pr r r r r o o o o o f f f f f il il il il ile m e mo o o o o un e m e m unt t t t t in in in in ing g g g g un un
w p e m un
6. Securely tighten the blade iron assembly screws.
7. Repeat steps 4 through 6 until all blade irons are assembled.
Two Notches
and Blade Iron
Assembly
Screws
Shipping
Blocks
F F F F F i i i i i g g g g g ur ur ur ur ure 16 - A e 16 - A e 16 - A e 16 - As s s s s s s s s s e e e e e mb e 16 - A

hanging the fan

1. Raise the fan and place the hook through the loop on the ceil-
ing plate as shown in Figure 17. Use the note and arrow en-
graved in the ceiling plate to assist in determining the direc-
tion to assemble.
W W W W W A A A A A R R R R R N N N N N I I I I I N N N N N G: F G: F G: F G: Fa a a a a n m n ma a a a a y f y f y f y f y fa a a a a ll i ll i ll i ll i ll if n n m n m
G: F n m
t t t t t h h h h h e e e e e s s s s s e in e in e in e ins s s s s t t t t t a a a a a ll ll ll ll lla a a a a t t t t t i i i i i o o o o o n in e in n in n ins s s s s t t t t t r r r r r u u u u u c c c c c t t t t t i i i i i o o o o o n n n n n s s s s s . . . . . n in n in
Hook
F F F F F i i i i i g g g g g ur ur ur ur ure 17 - Ha e 17 - Ha e 17 - Han n n n n g g g g g in in in in ing t e 17 - Ha
e 17 - Ha

wiring the fan

1. Disconnect the power by turning off the circuit breakers to
the outlet box and associated wall switch location.
2. You can use either one or two wall switches to control the fan
and/or lights separately. Use connection 1, as described in Fig-
ure 18, to
• control the light with a wall switch and the fan with a pull
chain (one wall switch required),
• control the light with a pull chain and the fan with a wall
switch (one wall switch required), or
• control the light with one wall switch and the fan with
another (two wall switches required).
Blade Iron
mblin mb mb mb lin ling t lin lin g t g t g t g th h h h h e b e b e b e bl l l l l a a a a a d d d d d e ir e b e ir e ir e ir e iro o o o o n n n n n
f n f n f n f no o o o o t a t a t as s s s s s s s s s e e e e e mb t a t a mb mb mbl l l l l e e e e e d a d a d a s dire e e e e c c c c c t t t t t e e e e e d in s dir s dir
mb d as dir d a s dir
Loop
g t g th h h h h e f e f e f e f e fa a a a a n n n n n g t g t
© 2003 Hunter Fan Company
d in d in
d in d in