Page 1
Mini CirCular Saw Model 97200 Set up and Operating inStruCtiOnS Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. ® distributed exclusively by Harbor Freight tools 3491 Mission Oaks Blvd., Camarillo, CA 93011...
Notice Notice related to personal injury. CautiOn, without the safety alert symbol, CautiOn CautiOn is used to address practices not related to personal injury. SKU 97200 For technical questions, please call 1-800-444-3353. Page 2...
Blade. Safety equipment such as dust mask, non-skid safety shoes, work gloves, or hearing protection used for appropriate conditions will reduce personal injuries. SKU 97200 For technical questions, please call 1-800-444-3353. Page 3...
Page 4
Use of the power tool for operations different from those intended could result in a hazardous situation. SKU 97200 For technical questions, please call 1-800-444-3353. Page 4...
Avoid unintentional starting. Prepare to begin work before turning on the tool. Do not lay the tool down until it has come to a complete stop. Moving parts can grab the surface and pull the tool out of your control. SKU 97200 For technical questions, please call 1-800-444-3353. Page ...
Page 6
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities, contains chemicals known [to the State of California] to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: SKU 97200 For technical questions, please call 1-800-444-3353. Page ...
“live” terminal. (See 3-prong plug and Outlet.) The tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet SKU 97200 For technical questions, please call 1-800-444-3353. Page 7...
(See table a.) If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use. SKU 97200 For technical questions, please call 1-800-444-3353. Page ...
Page 9
* Based on limiting the line voltage drop to five volts at 150% of the rated amperes. Symbology Double Insulated Volts Alternating Current Canadian Standards Association Amperes No Load Revolutions per Minute n 0 xxxx/min. Underwriters Laboratories, Inc. (RPM) SKU 97200 For technical questions, please call 1-800-444-3353. Page 9...
Remove the Hole Cover (39) and use the mm Hex Wrench to remove the Nut (3). Slide the Bolt (42) out and remove the Blade Guard (37) from the unit. SKU 97200 For technical questions, please call 1-800-444-3353. Page 10...
• this Saw is not recommended for cutting plasterboard because the dust may cause the Blade Guard to stick. SKU 97200 For technical questions, please call 1-800-444-3353. Page 11...
Turn the dust collector on. Hold the Saw with both hands and push the power switch forward. Do not cover the vents. Allow SKU 97200 For technical questions, please call 1-800-444-3353. Page 12...
Page 13
Once the cut is finished lift the Saw away from the workpiece before turning it off. To prevent accidents, turn off the tool and disconnect its power supply after use. Clean, then store the tool indoors out of children’s reach. SKU 97200 For technical questions, please call 1-800-444-3353. Page 13...
A buildup of dust will cause the Blade Guard to stick and may cause the unit to malfunction. warning! if the supply cord of this power tool is damaged, it must be replaced only by a qualified service technician. SKU 97200 For technical questions, please call 1-800-444-3353. Page 14...
If product has no serial number, record month and year of purchase instead. note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 97200 For technical questions, please call 1-800-444-3353. Page 17...