Page 1
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein.
In the event of a malfunction or breakdown, performance. Follow instructions for grounding provides a path of least lubricating and changing accessories. resistance for electric current to reduce the risk of electric shock. This tool is SKU 97360 For technical questions, please call 1-800-444-3353. Page 3...
Page 4
125 V~ 3-Prong Plug and Outlet. Make sure the workpiece is supported The outlet must be properly installed at all times while sawing. and grounded in accordance with all codes and ordinances. SKU 97360 For technical questions, please call 1-800-444-3353. Page 4...
Page 5
If the plug or receptacle does get wet, DON’T unplug the cord. Disconnect the SKU 97360 For technical questions, please call 1-800-444-3353. Page 5...
NIOSH-approved for the which cannot be built into this product, specific hazards in the work area. but must be supplied by the operator. SKU 97360 For technical questions, please call 1-800-444-3353. Page 6...
(while still keeping safe control of it). Let the tool do the work. To reduce vibration, maintain the tool as explained in this manual. If any abnormal vibration occurs, stop use immediately. SAVE THESE INSTRUCTIONS. SKU 97360 For technical questions, please call 1-800-444-3353. Page 7...
UNPACKING When unpacking, make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at 1-800-444-3353 as soon as possible. INSTRUCTIONS FOR PUTTING INTO USE...
Page 9
Figure 6, above. to keep the Tile Saw stand balanced evenly on the floor. (See Figure 4.) Remove the shipping screw and attach the Knob (22) through the slot SKU 97360 For technical questions, please call 1-800-444-3353. Page 9...
Stand II (64) using Bolts (120), Hex Nuts (123) and Washers (121). (See Figures 7A-7E) Lift the saw stand with the front handle to move it, as shown in figure 7E. SKU 97360 For technical questions, please call 1-800-444-3353. Page 10...
Wear ANSI approved safety glasses under an ANSI approved full face safety shield and non-skid safety shoes. Hearing and breathing protection must be used for appropriate conditions. SKU 97360 For technical questions, please call 1-800-444-3353. Page 11...
Page 12
NOTE: If the Motor of the Tile Saw stops suddenly while cutting, turn the Power Switch (37) to its “OFF” position. Wait approximately 5 minutes. While making sure your hands are dry, reset the Circuit SKU 97360 For technical questions, please call 1-800-444-3353. Page 12...
Page 13
To cut the tile, follow the same procedure as outlined in the section To cut the tile, follow the same “To Make A Straight Cut”. procedure as outlined in the section “To Make A Straight Cut”. SKU 97360 For technical questions, please call 1-800-444-3353. Page 13...
Page 14
(See Figure 16.) CAUTION! Never FLANGE ROTATION flip over a used Saw Blade. ARROW NUT (6) BLADE FIGURE 16 With one Wrench (71), hold the end of the Motor Spindle firmly and with SKU 97360 For technical questions, please call 1-800-444-3353. Page 14...
Page 15
Once the Saw Blade (4) is installed, reattach the Outside Flange (5) and Nut (6). Fasten the Nut by turning it counterclockwise until snug. Do not overtighten. (See Figure 16.) SKU 97360 For technical questions, please call 1-800-444-3353. Page 15...
Pump if the unit contains water in any debris on the Filter and Impeller. If freezing temperatures. Store the Tile necessary, replace the old Filter. When Saw indoors in a dry, frost-free room. SKU 97360 For technical questions, please call 1-800-444-3353. Page 16...
ER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 97360 For technical questions, please call 1-800-444-3353. Page 17...
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and dura- bility standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance.