Timer Alarm; Using The Alarms And Hourly Time Signal; Configuring Home Time Settings - Casio 3014 Operation Manual

Operation Guide 3014
Timer Mode Screens
Countdown Screen
Number of repeats
Remaining time
• The number of repeats flashes while Timer 2 is counting down.

Timer Alarm

The alarm sounds for five seconds when the end of each countdown is
reached. The alarm sounds for 10 seconds when the end of the final
countdown is reached.
To stop the alarm beeper
Press any button. Pressing a button will stop the alarm only, without
performing the normal function assigned to that button.

Using the Alarms and Hourly Time Signal

Your watch comes with three alarms and an hourly time signal.
Daily Alarms (ALM 1, ALM 2, ALM 3)
The watch beeps for about 10 seconds when an alarm time is reached.
Hourly Time Signal
The hourly time signal causes the watch to beep every hour on the hour.
Alarm and hourly time signal settings are
configured in the Alarm Mode, which you enter by
pressing the D button four times while in the
Timekeeping Mode.
To display an alarm screen
In the Alarm Mode, use the B button to scroll through the alarm
screens.
• Holding down the B button scrolls at high speed.
Alarm 1
Alarm time
Current time
Alarm number
Hourly Time Signal
To set an alarm time
1. In the Alarm Mode, display the screen of
(2 seconds)
the alarm whose setting you want to
change.
2. Hold down the A button for about two
seconds until the hour digits of the
current alarm time start to flash. This is
the setting screen.
• Displaying the setting screen also
turns on the alarm automatically and
causes the alarm on indicator to
appear on the screen.
3. Use the E (+) and B (–) buttons to change the hour setting.
• Holding down either button changes the setting at high speed.
• When setting the hour, make sure you specify AM or PM (P)
correctly when using 12-hour timekeeping, or that you specify the
correct 24-hour time. The same 12-hour/24-hour format you select
for the Timekeeping Mode time is also applied in the Alarm Mode.
Countdown Screen with
Heart Rate Monitor
Time remaining until auto start
Heart rate
Alarm 2
Alarm 3
4. Press the D button to move the flashing to the minutes.
5. Use the E (+) and B (–) buttons to change the minute setting within
the range of 0 to 59.
• Holding down either button changes the setting at high speed.
6. After all the settings are the way you want, press the A button to exit
the setting screen.
• The watch also will exit the setting screen automatically if you do not
perform any operation for about two or three minutes.
To turn an alarm or the hourly time signal on or off
While the screen for an alarm or the hourly time signal is on the display,
press the E button to toggle it on (alarm/Hourly time signal on indicator
displayed) and off (indicator not displayed).
• When any alarm is turned on, the alarm on indicator is displayed in all
other modes.
Alarm
Alarm on indicator
To stop the alarm beeper
Press any button.
To test the alarm
In the Alarm Mode, hold down the E button to sound the alarm.

Configuring Home Time Settings

(2 seconds) 1. In the Timekeeping Mode, hold down the
A button for about two seconds until
the seconds digits of the current time
start to flash. This is the setting screen.
2. Configure the Home Time settings as
shown below.
• Use the D button to move to the next
setting. Use the E (+) and B (–)
buttons to change the currently
selected setting.
• Holding down the E or B button
changes the current setting at high
speed.
3. After all the settings are the way you
want, press the A button to exit the
setting screen.
• The watch also will exit the setting screen
automatically if you do not perform any
operation for about two or three minutes.
I Seconds Reset to 00
Press the E button.
• 00 to 29, no change in minutes.
• 30 to 59, increases minutes by 1.
D
Hourly Time Signal
Hourly time signal on indicator
9