Casio 2615 Operation Manual

MO0601-EA
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to carefully read this manual.
Keep the watch exposed to bright light
Bright Light
Solar cell
• The watch continues to operate, even when it is not exposed to light. Leaving the
watch in the dark can cause the battery to run down, which will cause some watch
functions to be disabled. If the battery goes dead, you will have to re-configure watch
settings after recharging. To ensure normal watch operation, be sure to keep it
exposed to light as much as possible.
Battery charges in the light.
Bright Light
Solar cell
(Converts light to
electrical power.)
LEVEL 1
LEVEL 2
Charge
LEVEL 3
Rechargeable battery
General Guide
• Press C to change from mode to mode.
• In any mode, press L to illuminate the display.
Timekeeping Mode
Timekeeping
Month – Day
Hour : Minutes
Seconds
Day of week
PM indicator
3. When the setting you want to change is flashing, use D and B to change it as
described below.
Setting Screen
Seconds
Hour, Minutes
DST
12/24-Hour
Format
Year, Month, Day
Power Saving
4. Press A to exit the setting screen.
• See "Power Saving Function" for details about configuring Power Saving settings.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
• The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
Operation Guide 2615 3015
The electricity generated by the solar cell of the watch is
stored by a built-in battery. Leaving or using the watch
where it is not exposed to light causes the battery to run
down. Make sure the watch is exposed to light as much as
possible.
• When you are not wearing the watch on your wrist,
position the face so it is pointed at a source of bright
light.
• You should try to keep the watch outside of your sleeve
as much as possible. Even if the face of the watch is
only partially blocked from light, charging will be reduced
significantly.
Battery discharges in the dark.
Electrical
energy
All
LEVEL 1
functions
Dis- LEVEL 2
enabled
charge
LEVEL 3
Press C.
Stopwatch Mode
Use the Timekeeping Mode to set and view the current
time and date.
To set the time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Seconds DST Hour Minutes
Power Saving Day Month
Button Operation
Press D to reset to
.
00
Use D (+) and B (–) to change the setting.
Press D to toggle between Daylight Saving
Time ( ) and Standard Time (
ON OF
Press D to toggle between 12-hour (
24-hour ( 24H ) timekeeping.
Use D (+) and B (–) to change the setting.
Press D to toggle Power Saving on (
off ( OF ).
• The actual level at which some functions are disabled depends on the watch model.
• Frequent display illumination can run down the battery quickly and require charging.
The following guidelines give an idea of the charging time required to recover from a
single illumination operation.
Approximately 5 minutes exposure to bright sunlight coming in through a window
Approximately 50 minutes exposure to indoor fluorescent lighting
• Be sure to read "Power Supply" for important information you need to know
when exposing the watch to bright light.
If the display of the watch is blank...
If the display of the watch is blank, it means that the watch's Power Saving function
has turned off the display to conserve power.
• See "Power Saving Function" for more information.
About This Manual
(Light)
Module 2615
Some
(Light)
functions
Module 3015
disabled
Telememo Mode
Alarm Mode
Telememo
The Telememo Mode lets you store up to 30 records, each containing name and
telephone number data. Records are automatically sorted based on the characters of
the name. You can recall records by scrolling through them on the display.
Remaining memory
12/24-Hour
Format
• See "Sort Table" for details on how the watch sorts records.
• All of the operations in this section are performed in the Telememo Mode, which you
enter by pressing C.
Year
To create a new Telememo record
Number area
).
Name area
) and
12H
New Data Screen
ON ) and
(space)
4. When the character you want is at the cursor position, press C to move the cursor
to the right.
5. Repeat steps 3 and 4 until the name is complete.
• You can input up to eight characters for the name.
6. After you input the name, press C as many times as necessary to move the cursor
to the number area.
• When the cursor is located at the eighth space of the name area, moving the
cursor to the right causes it to jump to the first digit of the number. When the
cursor is at the 12th digit of the number, moving it to the right (by pressing C)
causes it to jump to the first character in the name.
• The operational procedures for Modules 2615 and 3015
are identical. All of the illustrations in this manual show
Module 2615.
• Button operations are indicated using the letters shown
in the illustration.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the "Reference" section.
World Time Mode
Countdown Timer Mode
Telephone number
Alternate at
two-second
interval
Name
1. In the Telememo Mode, use B and D to cycle through
the record screens until the new data screen appears.
• The new data screen is the one that is blank (contains
no name and telephone number).
• If the message FULL appears on the display, it
means that memory is full. To store another record,
you will first have to delete some of the records stored
in memory.
2. Hold down A until the flashing cursor (_) appears in
the name area of the display.
3. In the name area, use D and B to cycle through
characters at the cursor position. The characters cycle
in the sequence shown below.
Press D.
0 - .
A Z 9
to to
Press B.
: /
1