Advertisement
OPERATING yOUR BREvILLE CHILL CONTROL™
2.
Immerse the filter cartridge in cold
water and agitate gently to remove
any air bubbles.
3.
Insert the cartridge into the cartridge
housing of the pre-filter tank and push
firmly into place until it clicks into
position.
4.
Take the pre-filter tank out of the water
tank, fill it under the tap with cold tap
water and allow it to filter through.
Discard the first two fillings. They are
used to flush the filter cartridge.
5.
Place the pre-filter tank back into the
unit and refill with water. Ensure the
water is always above the minimum
level for optimum flow rate.
6.
The Breville Chill Control™ is now
ready for use.
NOTE
Repeat the above process every time
you insert a new cartridge.
7.
Once the water has been filtered, the
pre-filter tank can be refilled. Water will
filter through as it dispensed into the
filter tank water.
It will take 6 minutes on average to
filter 1 litre of water through the
BRITA
‰
MAXTRA cartridge.
10
LEd INdICATOR
The WHITE light will turn On first to
indicate the appliance is in cooling mode.
When the water inside the cooling reservoir
has chilled (approximately 75 minutes )
the LED indicator will change to BLUE.
In warmer climates the time to chill will
take longer.
AdjUSTING THE WATER
TEMPERATURE
The variable temperature slider allows you
to adjust the temperature of filtered water
to suit your taste.
The temperature of the water will vary
depending on the selection made.
Slide the lever to the far left for the coldest
setting or to the right for room temperature
filtered water.
A selection in the middle will give you
filtered water somewhere between chilled
and room temperature.
NOTE
The LED indicator does not change
colour when adjusting the variable
temperature control slider.
NOTE
If dispensing more than 1 litre of
chilled water at one time, it will
take approximately 75 minutes for
another litre of water to be chilled to
minimum temp.
OPERATING yOUR BREvILLE CHILL CONTROL™
NOTE
We recommend you change the
‰
BRITA
MAXTRA filter every 8 weeks.
Replacement filters can be purchased
through major retail outlets or via
store.brita.com.au.
For additional questions on the
BRITA replacement filters, please
contact BRITA Consumer Service on
1300 557 762.
AUTO PROTECTION MOdE
If there is an error with internal electronics
or the fan is externally obstructed, the LED
will start to flash, alternating between BLUE
and WHITE and the appliance will enter
into auto protection mode.
To reset the appliance, unplug the unit from
the power outlet, wait for a few minutes until
the LED stops flashing, and plug back into
power outlet.
If the LED continues to flash once reset,
contact Breville Customer Service
1300 139 798 for further assistance.
USING THE BRITA
MEMO
®
It is important to change your filter
cartridge regularly to enjoy the benefits
of filtered water.
The BRITA
‰
Memo (electronic exchange
indicator) reminds you when your filter
cartridge needs to be changed. It is
automatically calibrated according to
average use of 1 litre of water per day
and will remind you to change your filter
every 8 weeks.
SETTING THE BRITA
MEMO
®
Once you have fitted and prepared your
filter cartridge, start the BRITA
‰
Memo
as follows:
1.
Press and hold the START button until
4 bars appear on the display and flash
twice. The filter replacement reminder
is now set.
2.
The flashing dot in the corner of the
display indicates the filter replacement
reminder is working.
3.
At the end of every 2 weeks, 1 bar will
disappear indicating the remaining
cartridge life. Ensure you have a new
‰
replacement BRITA
MAXTRA water
filter cartridge available when only
1 bar is showing.
11
Advertisement
