Husqvarna 137, 142 Instruction Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Chainsaw
  5. 137
  6. Instruction manual

Husqvarna 137, 142 Instruction Manual

Husqvarna chain saw instruction manual
Hide thumbs Also See for 137, 142:
Table of Contents

Advertisement

Quick Links

See also: Instruction Manual

Instruction Manual

Manuel d'instructions
Betriebsanweisung
Manual de instrucciones
English
Please read these instructions carefully make sure you understand them
before using this unit.
Français
Avant d'utiliser cet appareil, veuillez lire attentivement les instructions et
assurez- -vous de les avoir comprises.
Deutsch
Lesen Sie diese Hinweise zur Handhabung des Geräts aufmerksam durch.
Verwenden Sie es erst, wenn Sie sicher sind, daß Sie alle Anweisungen
verstanden haben.
Español
Lea atentamente las instrucciones y asegúrese de entenderlas antes de
utilizar esta unidad.
R
137/142
530166132
12/28/04

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 137, 142

Summary of Contents for Husqvarna 137, 142

  • Page 1: Instruction Manual

    Instruction Manual Manuel d’instructions Betriebsanweisung Manual de instrucciones English Please read these instructions carefully make sure you understand them before using this unit. Français Avant d’utiliser cet appareil, veuillez lire attentivement les instructions et assurez- -vous de les avoir comprises. Deutsch Lesen Sie diese Hinweise zur Handhabung des Geräts aufmerksam durch.

  • Page 2: Identification Of Symbols

    IDENTIFICATION (WHAT IS WHAT?) 1. Cylinder Cover 2. Front Handle 3. Front Handguard 4. Starter Cover 5. Chain Oil Tank 6. Starter Handle 7. Carburator Adjusting Screw 8. Choke Control 9. Rear Handle 10. ON/OFF Switch 11. Fuel Tank 12. Muffler IDENTIFICATION OF SYMBOLS WARNING! This chain...

  • Page 3: Safety Rules

    SAFETY RULES WARNING: Always disconnect spark plug wire and place wire where it can- not contact spark plug to prevent accidental starting when setting up, transporting, ad- justing or making repairs except carburetor adjustments. Because a chain saw is a high-speed wood- cutting tool, special safety precautions must be observed to reduce the risk of accidents.

  • Page 4: Kickback Warning

    S Mix and pour fuel in an outdoor area on bare ground; store fuel in a cool, dry, well ventilated place; and use an approved, marked container for all fuel purposes. Wipe up all fuel spills before starting saw. S Move at least 10 feet (3 meters) from fuel- ing site before starting engine.
  • Page 5 Elbow locked Thumb on underside of handlebar S Keep a good, firm grip on the saw with both hands when the engine is running and don’t let go. A firm grip will help you reduce kickback and maintain control of the saw. Keep the fingers of your left hand encir- cling and your left thumb under the front handlebar.

  • Page 6: Assembly

    through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnormal swellings. Prolonged use in cold weather has been linked to blood vessel damage in otherwise healthy people.

  • Page 7: Fueling & Lubrication

    Place chain onto the sprocket 8. Fit bottom of drive links between the teeth in the sprocket in the nose of the guide bar. 9. Fit chain drive links in bar groove. 10. Pull the bar forward until the chain is snug in the guide bar groove.

  • Page 8: Starting A Cold Engine

    cleaner products in the fuel tank or permanent damage may occur. BAR AND CHAIN LUBRICATION The bar and chain require continuous lubri- cation. Lubrication is provided by the auto- matic oiler system when the oil tank is kept filled. Lack of oil will quickly ruin the bar and chain.

  • Page 9: Cutting Methods

    WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an autho- rized service dealer if any part is worn to less than 0,5 mm thick.

  • Page 10: Felling Large Trees

    fall in a particular direction include: S The wind direction and speed. S The lean of the tree. The lean of a tree might not be apparent due to uneven or sloping terrain. Use a plumb or level to de- termine the direction of tree lean.

  • Page 11: Limbing And Pruning

    BUCKING WARNING: If saw becomes pinched or hung in a log, don’t try to force it out. You can lose control of the saw resulting in injury and/or damage to the saw. Stop the saw, drive a wedge of plastic or wood into the cut until the saw can be removed easily.

  • Page 12: Carburetor Adjustment

    caution when cutting small size limbs. Slender material may catch the saw chain and be whipped toward you or pull you off balance. S Be alert for springback. Watch out for branches that are bent or under pressure. Avoid being struck by the branch or the saw when the tension in the wood fibers is released.

  • Page 13: Bar Maintenance

    adjusting procedure. S Saw will not idle. See IDLE SPEED- -T ad- justing procedure. Idle Speed- -T Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Adjust speed until engine runs without chain movement (idle too fast) or stalling (idle too slow).

  • Page 14: Troubleshooting Table

    WARNING: Always stop unit and disconnect spark plug before performing all of the recommended remedies below except remedies that require operation of the unit. TROUBLE CAUSE Engine will not 1. Ignition switch off. start or will run 2. Engine flooded. only a few seconds after 3.

  • Page 15: Declaration Of Conformity

    We, Electrolux Home Products, Inc., Texarkana, TX, 75501, USA, Tél. : +1 903 223 4100, declare under sole responsibility that the Husqvarna models 137/142 chain saws were assessed in accordance with Annex V of the DIRECTIVE and from serial numbers 2004- -233(N or D)00001 and onwards, conforms to the provisions of the DIRECTIVE.

  • Page 16: Technical Data Sheet

    Type of oil pump Automatic Weight Without bar and chain, kg 4,6 CHAIN Length Pitch Inches Inches Tip Radius 0,325 10T Husqvarna H30 0,325 10T Husqvarna H30 0,050/ 3/16 0,325 YEAR OF CONSTRUCTION: 2005 MANUFACTURER’S ADDRESS: Husqvarna SE- -561 82 Huskvarna...

This manual is also suitable for:

142

Table of Contents