Advertisement
Advertisement
Table of Contents
Related Manuals for Plantronics Voyager Legend CS
Summary of Contents for Plantronics Voyager Legend CS
- Page 1 Voyager Legend ® Bluetooth Headset System User Guide...
- Page 2 Welcome Congratulations on purchasing your new Plantronics product. This guide contains instructions for setting up and using your Voyager Legend CS Wireless Headset System. Please refer to the separate safety instructions for important product safety information prior to installation or use of the product.
-
Page 3: What's In The Box
What's in the Box Base Headset Telephone interface cable Power supply Eartips Some models may also include: HL10 Lifter USB Charge cable... -
Page 4: Base And Headset Basics
Base and Headset Basics Base Call/mute LED Handset lifter/EHS cable jack Power on/pairing LED Telephone interface cable Charging LED Listening volume dial* Pairing button Speaking volume dial* Power jack Configuration switch* *For installation set up Headset Volume +/- button Call button Power button Mute microphone/voice command button Snap fit magnetic charge connection... - Page 5 Accessories Sold separately. Portable charge case Desktop charge stand AC charger USB charge cable* Car charge adapter Micro USB charge adapter Eartip kit (available in S, M, L) HL10 lifter* Automatically lifts handset and returns it to the cradle. Enables remote call control with your headset.
- Page 6 Change the eartip Change the eartip for a better fit. Push in eartip and rotate to the left to unlock it. Align new eartip into slot. Rotate it to the right to lock it into place. Wear on the left or right To wear the headset on your other ear, rotate the boom upwards then twist it around so the eartip is on the other side before lowering the boom.
-
Page 7: Connect Your Desk Phone
Charge for at least 20 minutes prior to the first use. A full charge takes 90 minutes. Connect and configure There are three setup options for connecting the Voyager Legend CS to your desk phone. your desk phone Select one of the following and continue. - Page 8 If you will be using the desk phone with an EHS cable, refer to Desk phone plus EHS cable section in this guide. For further installation information refer to the EHS Getting Started guide that came with your EHS cable or at plantronics.com/accessories. Desk phone (standard) Connect one end of the telephone interface cable to the back of the base.
- Page 9 Remove the handset from the desk phone cradle. While wearing your headset, press the call button on the headset. If you do not hear a dial tone, adjust the configuration switch (A-G) until you do. NOTE For most phones, these factory settings will sound best. Dial a test call from the desk phone.
- Page 10 Connect the end of the EHs cable to the base and the other end of the desk phone as described cable in the EHS Quick Start Guide. NOTE For further installation information refer to the EHS Quick Start Guide that came with your EHS cable or at www.plantronics.com/accessories...
- Page 11 Position your base The minimum recommended separation between your desk phone and the base is 6 inches. The minimum recommended separation between the base and computer is 12 inches. Incorrect position can cause noise and interference problems.
-
Page 12: Headset Overview
Play/Pause button (mobile phone use only) Talk time With a single full charge, the Voyager Legend CS will provide up to 7 hours of talk time and up to 11 days of standby time. Adjust the volume Toggle the Volume button (show icon) up (+) or down (-) during a call to adjust the volume. - Page 13 When you return to the operating range of the base or mobile phone, a voice prompt will announce: • "Phone 1 Connected"; audio restored if active NOTE Note: If both desk phone and mobile phone are connected to the headset it will be announce "Phone 1 Connected"...
- Page 14 Base LEDs 1 Call Status LED Idle = Unlit Incoming call = fast blue flash On call = solid blue Call (headset mic) muted = slow blue flash 2 Power On/Pairing LED Power off = unlit Powered = solid blue (headset paired/connected) Powered = solid red (headset not paired or disconnected) In pairing mode = red/blue flashing...
- Page 15 Your Base : Pairing Pairing your base to your headset Bluetooth pairing button The headset and base that came in the box are already paired to each other. However, if you wish to use a new headset or need to restore subscription to your current headset, the units can be paired to each other by doing the following.
- Page 16 Once successfully paired, LEDs stop flashing red and blue. The LED remains solid blue and you hear “pairing successful.” NOTE To enable caller name announcement, allow access to your contacts if your phone prompts you.
- Page 17 Remove the handset from the cradle, you will hear dial tone. This step will be automatic if you install a handset lifer or EHS cable accessory. For a complete list of accessories, visit www.plantronics.com/accessories Dial the number using your desk phone. To end the call, press the headset Call button and hang up the handset.
- Page 18 Call Controls - Mobile Phone Place a call Wearing the headset, press the Call button Dial the number using mobile phone. To end the call, press the Call Button on the headset or end via your mobile phone. Answer a call If wearing your headset press Call Button , or If wearing the headset and prompted, "Incoming call, answer or Ignore", say "Answer", or...
-
Page 19: Customize Your Headset
Customize Your Headset Your headset understands and speaks in English. You can change the language and other settings online. ™ MyHeadset Updater tool enables you to: • Receive firmware updates • Change language for voice alerts and commands (English U.K., French, German, and Spanish. Voice alerts are also available in Cantonese and Mandarin.) •... - Page 20 Features Listen to audio via A2DP Your Voyager Legend headset can play media files (music, podcasts, navigation, etc.) from any A2DP (Advanced Audio Distribution Profile for Bluetooth)-enabled mobile device. Transmission range Your Voyager Legend Bluetooth headset has a 10 meter effective range. Voice prompts from your headset will alert you if you lose connection with your base or mobile phone.
- Page 21 • "Cancel" • "Check battery" • "Ignore" • "Pair mode" • "Redial" • "What can I say" NOTE The voice-dial feature on your phone is initiated by pressing the Call button for 2 seconds. The voice-dial feature is not a headset voice command and only works with supporting phones. Disable the answer/ignore To disable the “answer/ignore”...
-
Page 22: Troubleshooting
Troubleshooting Headset Talk time performance is Battery is wearing out. Contact us at www.plantronics.com/ significantly degraded even after a support full recharge. Desk phone I can’t hear a dial tone in the Make sure your headset is charged. headset. Make sure your headset is subscribed to base. See Subscription button. -
Page 23: Need More Help
® Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Plantronics, Inc. is under license. All other trademarks are the property of their respective owners. Patents: US 8,208,673; D617,316; D681,003; 681,014; D681,002; D662,089; BR 3020120011493; CN ZL201230489876.9; ZL201230059196.3; EM 002109637-0001;...