Table of Contents
Advertisement
A A A A A n n n n n g g g g g l l l l l e M
e M
e Mo o o o o un
e M
e M
unt t t t t in in in in ing g g g g (Figure 3) hangs from a vaulted or angled ceiling.
un
un
un
F F F F F i i i i i g g g g g ur ur ur ur ure 3 - A
e 3 - An n n n n g g g g g l l l l l e m
e 3 - A
e 3 - A
e 3 - A
preparing the fan site
These guidelines are designed to help you select the best location
for your fan and to prepare the site prior to installing the fan. Proper
ceiling fan location and attachment to the building structure are
essential for safety, reliable operation, maximum efficiency, and en-
ergy savings.
choosing the fan site
Within the room where you want to install the fan, choose a fan
site where:
•
No object can come in contact with the rotating fan blades
during normal operation.
•
The fan blades are at least 7 feet above the floor and the
ceiling is at least 8 feet high.
•
The fan blades have no obstructions to air flow, such as
walls or posts, within 30 inches of the fan blade tips.
•
The fan is directly below a joist or support brace that will
hold the outlet box and the full weight of the fan.
See Figure 4 for the minimum mounting distances.
8' Minimum
Ceiling Height
7' Minimum
to Floor
F F F F F i i i i i g g g g g ur ur ur ur ure 4 - M
e 4 - M
e 4 - Min in in in inimum m
e 4 - M
imum mo o o o o un
imum m
imum m
e 4 - M
imum m
© 2003 Hunter Fan Company
34 º Max
8
Pitch
12
e m
e mo o o o o un
e m
unt t t t t in in in in ing g g g g
un
un
e m
un
30" From
Wall or
Nearest
Obstruction
unt t t t t in in in in ing di
un un
un
g di
g dis s s s s t t t t t a a a a a n n n n n c c c c c e e e e e s s s s s
g di
g di
using an existing fan site
If you are preparing a new fan site, go to the p p p p p r r r r r e e e e e p p p p p a a a a a r r r r r in in in in ing a n
si si si si sit t t t t e e e e e section.
If you plan to use an existing fan site, complete the following check-
list for the support brace, ceiling hole, outlet box, and wiring. If you
cannot check off every item, see the p p p p p r r r r r e e e e e p p p p p a a a a a r r r r r in in in in ing a n
tion for instructions on properly preparing the site for your new
fan.
fan support system
•
Fan must attach directly to building structure.
•
Fan support system must hold full weight of fan and light
kit.
ceiling hole
•
Outlet box clearance hole directly below the joist or sup-
port brace.
outlet box
•
UL-approved octagonal 4" x 1-1/2" outlet box (or as speci-
fied by the support brace manufacturer).
•
Outlet box secured to joist or support brace by wood
screws and washers through inner holes of outlet box.
•
Outer holes of outlet box aligned with joist or support
brace.
•
Bottom of outlet box recessed a minimum of 1/16" into
ceiling.
wiring
•
Electrical cable secured to outlet box by approved con-
nector.
•
Six inches of lead wires extend from outlet box.
See Figure 5 for an adequate existing fan site.
Support Brace
Washer
Wood Screw
F F F F F i i i i i g g g g g ur ur ur ur ure 5 - A
e 5 - A
e 5 - Ad d d d d e e e e e q q q q q u u u u u a a a a a t t t t t e ex
e 5 - A
e 5 - A
If your existing fan site is suitable, go to the in in in in ins s s s s t t t t t a a a a a llin
p p p p p l l l l l a a a a a t t t t t e e e e e section and begin installing your new Hunter fan.
preparing a new fan site
To prepare the fan site follow four steps:
•
Cutting the Ceiling Hole
•
Installing the Support Brace (if necessary)
•
Installing the Outlet Box
•
Preparing the Wiring
g a n
g a n
g a ne e e e e w f
w f
w fa a a a a n n n n n
w f
g a n
w f
g a n
g a n
g a n
g a ne e e e e w f
w f
w fa a a a a n si
w f
w f
n sit t t t t e e e e e sec-
n si
n si
n si
Ceiling Joist
Approved
Connector
Ceiling
Outlet Box
e ex
e ex
e exi i i i i s s s s s t t t t t in in in in ing f g f g f g f g fa a a a a n si
n sit t t t t e e e e e
n si
n si
e ex
n si
llin
llin
lling t
llin
g th h h h h e c
g t
g t
g t
e ce e e e e ilin
e c
e c
e c
41847-01 04/21/2003
3 3 3 3 3
ilin
iling g g g g
ilin
ilin
Advertisement
Table of Contents
