Huffy Portable Basketball System Owner's Manual page 6

IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS
1. Mark pole sections with tape as shown.
2. IMPORTANT! Bounce pole top (1) and middle section (2) together as shown
until they no longer move toward taped reference mark. Upright assembly.
NOTE: Pole sections should have a 3-1/2" (9 cm) minimum overlap.
3. IMPORTANT! Holes in top (1) and bottom pole (3) sections MUST align to
correctly position elevator system toward playing surface. Add bottom pole
section (3) to assembly as shown and bounce until completely tight. NOTE: Pole
sections should have a 3-1/2" (9 cm) minimum overlap.
4. Install rod (4) through holes in bottom pole section (3) and eyebolt (5).
Insert pole assembly into tank assembly (6) as shown. Secure pole assembly with
disk (7) and lock nut (8).
NOTE: Two people recommended for this step.
5. Secure base struts (9) to pole using bolt (10) washers (11) and nut (12) as shown.
Rotate the non-secured ends of base struts (9) as shown.
6. Secure base struts (9) to base using bolt (14) washers (11) and nut (15).
7. Insert axle rod (16) through wheel (17), as shown. Secure wheel assembly to tank
(6) by tapping wheel downward with hammer, snapping it into position. Carefully,
turn tank (6) over.
8. Install upper pivot bracket (18) to front of base using bolt (19), washer (20) and nut
(8) as shown.
9. Insert bolt (21) through lower pivot bracket (22) as shown, bolt (21) will be secured
during step 12.
Carefully place base assembly on its side. Install lower pivot bracket (22) with bolt
(23), washers (20) and lock nut (8) as shown.
10. Secure both hinge tubes (22) to wheel bracket (25) with carriage bolts (26) and
flange nuts (15).
11. Install wheels (27) onto axle (28) and wheel bracket (25) with push caps (29) as
shown.
12. Position base as shown. Secure wheel bracket assembly with disc (30), washer
(20) and nut (8) as shown. NOTE: Two people recommended for this step.
13. Carefully reposition entire assembly as shown. IMPORTANT! Two people
recommended for this step.
14. Snap tinnerman nut (31) onto inner channel (32). Place inner channel into outer
channel (33) as shown.
15. Slide handle (34) into position as shown and secure with bolts (35), washers (35),
and nuts (15). Tighten completely.
16. Install bolt (36), washers (11), and nut (37) as shown. Tighten until washers (11)
are no longer loose. NOTE: Do not over tighten. Assemble trigger (22) to handle
assembly (34, 32, 33) as shown and secure with bolt (39) and washer (11). Tighten
completely.
17. WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS.
Install trigger return spring (40) to handle assembly (32, 33) as shown.
18. Attach Accuheight label (41) to outer channel (33).
19. Attach spring (44) to pins (43) and install pins (43) onto pole mount bracket (45).
Attach other spring (44) to opposite side. NOTE: Gently enlarge eyelets of spring
with pliers if springs do not fit over pins.
WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS.
20. Install pole mount assembly and reinforcement bracket (47) with carriage bolts (46)
to pole as shown. Tighten flange nuts (15) completely.
21. Push back sliding pin (43) as shown in Figure A to fit adjustable system assembly
through pole mount assembly. Then attach spring covers (48 & 49) onto pole mount
bracket (45) with bolt (50), and nut (15) as shown in Figure B.
22. Install spacers (51) onto backboard brackets (52) with bolts (53, 54) and lock-nuts
(55, 37) as shown.
P/N 211260A 10/01
INSTRUCTIONS
OWNERS MANUAL
WARNING: IF YOUR SYSTEM IS EQUIPPED WITH AN ACRYLIC
BACKBOARD, EXAMINE BACKBOARD FOR ANY DAMAGE THAT MAY
HAVE OCCURRED DURING SHIPMENT. CRACKS IN THE BACKBOARD
COULD RESULT IN SUDDEN BREAKAGE. IF BACKBOARD IS DAMAGED
IN ANY WAY PRIOR TO OR AFTER ASSEMBLY, CALL TOLL-FREE
NUMBER FOR FREE REPLACEMENT:
U.S. 1-800-558-5234; CANADA: 1-800-284-8339; http://www.huffysports.com
23. Assemble lower elevator tubes (56) as shown. NOTE : Tighten bolt (57) in lock nut
(58) until flush (even) with lock nut's outer edge. IMPORTANT! It is necessary for
all parts to be installed for this mechanism to work safely and properly.
NOTE: Test fit bolts into holes of brackets (52) and carefully rock them in a circular
motion to ream out paint from holes if necessary
24. Bend brackets (52) to line up with holes in channel. Insert carriage bolts (62) into
hole as shown. Tighten completely.
Insert Tee-bolt (69) through Slam Jam Bracket (61) and attach to backboard with
nuts (15) and bolts (61) as shown.
25. Assemble upper elevator tubes (63) to backboard brackets (52) as shown. NOTE:
Tighten bolt (57) in lock nut (58) until flush (even) with lock nut's outer edge.
26. Support pole on sawhorse. Attach backboard assembly to top pole section (1) as
shown. Then install pole cap (64). NOTE: Two people are recommended for this
step. Use caution; elevator assembly is heavy.
27. Install upper elevator tubes (63) to triangle plates (66) as shown.
Install handle assembly to lower elevator tubes (56) using bolt (57), spacers (67),
and nut (58) as shown. NOTE: Tighten bolt (57) in lock nut (58) until flush (even)
with lock nut's outer edge. NOTE: Before going on to next step, set adjustable
system assembly to the 10' (3.05 m) setting.
28. WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS.
Insert bolt (57) through left side upper elevator tube (63), then stretch springs (68)
onto bolt (57). Insert bolt (57) through right side upper elevator tube (63) and
secure with nut (58).
29. Install net clips (81). The Quick Clip™ rapid release net system lets the net pull
away from the rim. This reduces the risk of player injury or property damage.
However, improper installation or a ball making contact at an odd angle may
disengage the net clip from the goal rim. Usually, the clip is reinstalled with little or
no problem. We hope that you agree this inconvenience is minor when compared
to the safety of the players. Quick Clip: US Patent No. 5,792,010/5,795,253
The two outer hooks on net clip must face towards inside of goal rim. Insert larger
hole in net clip onto rim stud, push down on net clip, then slide net clip right, locking
or snapping securely into position (clips must "snap" into place to insure a secure
fit).
NOTE: Net clips should not slide with ease. It is very important that the net clips
are in the locked position before going on to next step.
WARNING: USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF
NET CLIPS, OR WHEN ALL NET CLIPS ARE NOT PRESENT COULD RESULT
IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY.
30. Fit rim (70) into Slam Jam Bracket (61) and assemble Slam Jam Rim as shown.
WARNING: TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT
FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY
AND/OR PROPERTY DAMAGE.
31. Install net (76).
IMPORTANT! Make sure net is held by all three hooks on the net clip.
A. Slide net into outer hook as shown.
B. Slide net into second outer hook creating a loop as shown. Push loop to back of
clip.
C. Pull loop up and through back of clip, snapping over the middle hook.
D. Pull net down to make sure it is held securely by all three hooks.
NOTE: If net releases during normal play, net was improperly installed. Please
review instructions to install net properly.
32. Attach front cover (82) to hinge tubes (24) using carriage bolt (42) and flange nuts
(15) as shown.
WARNING: DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY, MAY
TIP OVER.
33. Apply height and moving label (77) to front of pole as shown.
34. Roll completed assembly to desired playing area. Secure assembly to ground using
rope (78) and tie down stake (79). Fill tank with 34 gallons of water. IMPORTANT!
Add two gallons (7.6 Liters) of non-toxic antifreeze in sub-freezing climates.
Add two gallons (7.6 liters) to tank to prevent freezing in sub-freezing climates.
Snap cap (80) into place.
WARNING: DO NOT ALLOW CHILDREN TO ADJUST HEIGHT.
35. Grasp handle and depress lever.
36. Push toward pole while holding lever. Raise or lower lever to desired height while
pushing forward on handle.
37. Release handle making sure that horizontal pin (43) is locked into slot.
6
printed on recycled paper