Related Manuals for Meyra PROFI 3
Summary of Contents for Meyra PROFI 3
- Page 1 WHEELCHAIRS AND REHABILITATION EQUIPMENT ACTIVE WHEELCHAIR PROFI 3 Model 2.871 Model 2.875-S Model 2.871 Model 2.875 OPERATING MANUAL...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Introduction Acceptance Assembly Specifications / Utilization Driving behavior Safety instructions Driving training General overview Brakes Legrests Leg retainer Armrests Mudguard Backrest Backrest belt Seat belt Drive wheels Centre of gravity Wheel camber Toe-in Handrims Hand and spoke guard Steering wheels Front seat-height Seat tilt... -
Page 3: Introduction
INTRODUCTION ACCEPTANCE ASSEMBLY With the PROFI 3 model 2.871 and All MEYRA wheelchairs are tested in our Your PROFI 3 will have been assem- model 2.875-S from MEYRA, you own factory for fault-free operation, and are bled and adapted to your personal a highly sophisticated sport wheelchair packed in special boxes. -
Page 4: Specifications / Utilization
Due to the numerous infinitely-variable the PROFI 3 to your personal needs ( see adjustment possibilities of the PROFI 3, – Read and observe the Safety Notes... -
Page 5: General Overview
BRAKES Locking the pressure brakes The model shown in Fig. 4 and 5 is the The PROFI 3 can be upgraded with a standard version. All deviations are removable pressure brake, code 305 Push both brake levers (11) forward as specified separately in this operating (Fig.6). -
Page 6: Legrests
LEGRESTS LEG RETAINER ARMRESTS The legrests and the crash bar code The leg retainer code 316 (Fig.11) is Model 2.871 310 are height-adjustable by 60mm in mounted by way of a clamp on the front The choice of foldable or slide-action 4 positions. -
Page 7: Mudguard
MUDGUARD BACKREST Model 2.875-S Adapting the clothes guard The backrest can be folded and its an- gle can be adjusted by approx. ± 10° The removable clothing guards running Height adjustment (Fig.16): (Fig.19). parallel to the wheel circumference The height adjustment of the clothing must be adapted to the chosen wheel Benefits: guard is infinitely variable. -
Page 8: Backrest Belt
BACKREST BACKREST BELT DRIVE WHEELS Angle adjustment The backrest belt slackness can be ad- Note: justed to the personal needs of the user The angle adjustment occurs after the You will find the air pressure values by way of the Velcro fastener (Fig.23 locking pieces (C, Fig.22) have been for the tyres for your wheelchair in the and 24). -
Page 9: Centre Of Gravity
CENTRE OF GRAVITY WHEEL CAMBER TOE-IN The adjustment should be car- The adjustment should be car- The adjustment should be car- ried out by the specialist ried out by the specialist ried out by the specialist dealer! dealer! dealer! The centre of gravity is infinitely variable The wheel camber (Fig.30) can be set The toe-in can be adjusted by rotating by way of axle tube displacement. -
Page 10: Handrims 1
TOE-IN HANDRIM STEERING WHEELS Note: All handrims [9] are designed for a dis- The steering wheels can be exchanged tance to the driving wheel [8] of 15 mm without difficulty. If toe-in adjustment equipment is not (standard setting) and 25 mm (Fig.34). available, use two items of identical Handling: Replacement of handrims or modifica-... -
Page 11: Seat Tilt 1
SEAT TILT STEERING HEAD AD- PUSH HANDLE JUSTMENT The adjustment should be car- The insertion tubes (Fig.40) can be re- ried out by the specialist placed with push handles (Fig.41). The adjustment should be car- dealer! ried out by the specialist Fitting push handles dealer! The seat tilt is infinitely variable by con-... -
Page 12: Maintenance
Finish: Before starting out Like any other technical product, your The high quality finish ensures an opti- Profi 3 also needs to be maintained. mum of protection against corrosion. If 1. Test brakes for faultless op- The following maintenance instructions... -
Page 13: Maintenance Instructions 1
MAINTENANCE IN- SPECIAL VALVE STRUCTIONS The drive wheels (14) are equipped with a special valve (Fig.42) in the case Every 6 months 4. Check tyre profiles, axle of tyre pressure of up to 11 bar. (depending on frequency of use) tube, frame tubes for cracks or Use the following for an easier pumping other damage... -
Page 14: Technical Data
The following pressure values can be Attention: taken as standard values: For the transport in vehicles, you must leave the PROFI 3 and occupy a suita- Driving wheel: ble seat in the vehicle. It is forbidden Code 486 to remain seated in the PROFI 3 dur- Standard = 4.0 bar... - Page 15 TECHNICAL DATA Table 1 All length and height data in the table 1 relates to the Profi 3, model 2.871. – Backrest height 38 cm – Depth of seat 40 cm – Frame length 58 cm – Overall length 77 cm –...
- Page 16 TECHNICAL DATA o r f - t a o r f - t a i r e ø l l l i r l l i r l l i r l l i r l l i r l l i r l l i r ø...
- Page 17 TECHNICAL DATA All length and height data in the table 2 Table 2 relates to the PROFI 3, model 2.875-S: – Backrest height 38 cm – Depth of seat 40 cm – Frame length 58 cm – Overall length 77 cm –...
-
Page 18: Notes 1
NOTES... -
Page 19: Guarantee 1
– 3 years for the frame. use of the wheelchair as per instructions of MEYRA will lead to general loss of We reserve the right to make technical and the regular implementation of main- guarantee and product liability. - Page 20 Retailer stamp WHEELCHAIRS AND REHABILITATION EQUIPMENT MEYRA Wilhelm Meyer GmbH & Co. KG • Company address: Meyra-Ring 2 D-32689 Kalletal-Kalldorf Telephone +49 (0) 5733 922-0 Telefax: +49 (0) 5733 922-143 e-mail: info@meyra.de Internet: http://www.meyra.de Postal address: P.O. Box 1703 D-32591 Vlotho...
-
Page 21: Illustration Section Of The Operating Manual
ROLLSTÜHLE UND REHABILITATIONSMITTEL AKTIV-ROLLSTUHL Bildteil zur Betriebsanleitung Illustration Section of the Operating Manual Illustration du mode d`emploi Illustrazioni relative alle istruzioni d’uso Fotos para las instrucciones de funcionamiento Afbeelding voor Gebruiksaanwijzing Modell 2.871 Modell 2.875... - Page 22 PROFI 3, MODELL 2.871 PROFI 3-S, MODELL 2.875...
- Page 26 ROLLSTÜHLE UND REHABILITATIONSMITTEL MEYRA Wilhelm Meyer GmbH & Co. KG • Firmensitz: Meyra-Ring 2 D-32689 Kalletal-Kalldorf Telefon (05733) 922-0 Telefax: (05733) 922143 Email: info@meyra.de Internet: http://www.meyra.de Postanschrift: Postfach 1703 D-32591 Vlotho •...