Gas Supply - White Mountain Hearth VFBL-30-1 Installation Instructions And Owner's Manual

The gas line can be routed either through the floor or wall. The
gas line opening should be made at this time. Location of the
opening will be determined by the position of floor joists and the
valve and union used for servicing.
Check all local codes for requirements, especially for the size and
type of gas supply line required.
Recommended Gas Pipe Diameter
Pipe Length Schedule 40 Pipe
(Feet) Inside Diameter
Nat.
0-10 1/2"
12.7mm
10-40 1/2"
12.7mm
40-100 1/2"
12.7mm
100-150 3/4"
19mm
Note: Never use plastic pipe. Check to confirm whether your local
codes allow copper tubing or galvanized.
Note: Since some municipalities have additional local codes, it is
always best to consult your local authority and installation code.
Installing a New Main Gas Cock
Each appliance should have its own manual gas cock.
A manual main gas cock should be located in the vicinity of
the unit. Where none exists, or where its size or location is not
adequate, contact your local authorized installer for installation
or relocation.
Compounds used on threaded joints of gas piping shall be resistant
to the action of liquefied petroleum gases. The gas lines must be
checked for leaks by the installer. This should be done with a soap
solution watching for bubbles on all exposed connections, and if
unexposed, a pressure test should be made.
Never use an exposed flame to check for leaks. Appliance must be
disconnected from piping at inlet of control valve and pipe capped
or plugged for pressure test. Never pressure test with appliance
connected; control valve will sustain damage!
A gas valve and ground joint union should be installed in the gas
16940-2-0806

GAS SUPPLY

Tubing, Type L
Outside Diameter
L.P. Nat.
3/8" 1/2"
9.5mm 12.7mm
1/2" 5/8"
12.7mm 15.9mm 12.7mm
1/2" 3/4"
12.7mm 19mm 12.7mm
1/2" 7/8"
12.7mm 22.2mm
Figure 1
line upstream of the gas control to aid in servicing. It is required
by the National Fuel Gas Code that a drip line be installed near
the gas inlet. This should consist of a vertical length of pipe tee
connected into the gas line that is capped on the bottom in which
condensation and foreign particles may collect.
L.P.
3/8"
9.5mm
1/2"
1/2"
3/4"
19mm
Method of Installing a Tee Fitting Sediment Trap (Figure 2)
The use of the following gas connectors is recommended:
— ANS Z21.24 Appliance Connectors of Corrugated Metal
Tubing and Fittings
— ANS Z21.45 Assembled Flexible Appliance Connectors of
Other Than All-Metal Construction
The above connectors may be used if acceptable by the authority
having jurisdiction.
Pressure Testing of the Gas Supply System
1. To check the inlet pressure to the gas valve, a 1/8" (3mm)
N.P.T. plugged tapping, accessible for test gauge connection,
must be placed immediately upstream of the gas supply con-
nection to the appliance.
2. The appliance and its individual shutoff valve must be discon-
nected from the gas supply piping system during any pressure
testing of that system at test pressures in excess of 1/2 psig
(3.5 kPa).
3. The appliance must be isolated from the gas supply piping
system by closing its individual manual shutoff valve during
any pressure testing of the gas supply piping system at test
pressures equal to or less than 1/2 psig (3.5 kPa).
ATTENTION! If one of the above preocedures results in pressures
in excess of 1/2 psig (14" w.c.) (3.5kPa) on the appliance gas
valve, it will result in a hazardous condition.
Checking Manifold Pressure
Natural gas will have a manifold pressure of approximately 3.5"
(.871kPa) w.c. at the pressure reggulator outlet with the inlet
pressure to the pressure regulator from a minimum of 4.5" w.c.
(1.120kPa) for the purpose of input adjsutments to a maximum
of 10.5" w.c. (2.614kPa) Propane gas will have a manifold
pressure approximately 10.0" w.c. (2.49kPa) at the pressure
regulator from a minimum of 11.0" w.c. (3.237kPa).
A test gage conection is located downstream of the gas appliance
pressure regulator for measuring gas pressure. The connection
is a 1/8 inch 3mm) N.P.T. plugged tapping.
Figure 2
Page 7