Field Wiring; Field Wiring Steps; Wiring Diagram - Lennox Hearth Products Rhapsody RHAP42N Installation Instructions Manual

LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS

fIELd WIRINg

NOT FOR USE WITH SOLID FUEL
CAUTION: Label all wires prior to discon-
nection when servicing controls. Wiring
CAUTION:
errors can cause improper and dangerous
operation.
touch. Severe Burns may result. Keep children, clothing,
ATTENTION: Au moment de l'entretien
furniture, gasoline and other liquids having flammable
des commandes, étiquetez tous les fils
vapors away.
avant de les débrancher. des erreurs
CAUTION:
de cáblage peu-vent entraîner un fonc-
tionnement inadéquat et dangereux.
factory installed refractory panel(s) removed, cracked or
Verify proper operation after servicing.
broken. Replacement of the factory installed refractory
S'assurer que l'appareil fonctionne adé-
panel(s) should be completed by a licensed or qualified
quatement une fois l'entretien terminé.
service person.
WARNING:
CAUTION
alteration, service or maintenance can cause injury
ground supply lead must be con-
or property damage. Refer to the owner's information
nected to the wire attached to the
manual provided with this appliance. For assistance
green ground screw located on the
or additional information consult a qualified installer,
outlet box. failure to do so will
service agency or the gas supplier.
result in a potential safety hazard.
The appliance must be electrically
Due to high temperatures, keep children, and furniture
grounded in accordance with local
away.
codes or, in the absence of local
codes, the National Electrical Code,
Keep burner and control compartment clean. See
ANSI/NfPA 70, latest edition (in installation and operating instructions accompanying
Canada, the current CSA C22.1
appliance.
Canadian Electrical Code).
ELECTRONIC
IGNITION WIRING
DIAGRAM
G
POWER CORD
FAN CONTROL
MODULE
WALL
RECEIVER
CABLE HARNESS
P/N 580095-01
Figure 43: Proflame Electronic Wiring Diagram
24
Electrical grounding Instructions
This appliance is equipped with a three-prong (grounding) plug for your
protection against shock hazard and should be plugged directly into
a properly grounded three-prong receptacle. dO NOT cut or remove
Hot while in operation. Do not
the grounding prong from the plug.
Do not operate the appliance with
Improper installation, adjustment,
Figure 42: Junction Box Wiring
1 2 0 V A C
Wiring Color Code
B = Black
W G
B
BL = Blue
BR = Brown
JUNCTION BOX
FAN
Power
Aux
120V Fan
Out
Out
R,PU,GY
HIGH-TEMP SLEEVE
Schematic Representation Only
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
WARNING:
Do not connect 120 V AC to the control valve.
DIRECT VENTED APPLIANCES MUST NOT BE OPERATED
WITHOUT THE FRONT GLASS PANEL(S) INSTALLED.
DO NOT OPERATE APPLIANCE WITH BROKEN,
green
White
CRACKED OR MISSING GLASS DOORS OR ENCLOSURE
PANEL(S).
THIS APPLIANCE MUST BE INSTALLED IN ACCORDANCE
WITH LOCAL CODES, IF ANY; IF NONE, FOLLOW THE
Tab Intact
NATIONAL FUEL GAS CODE, ANSI Z223.1, OR NATURAL
GAS AND PROPANE INSTALLATION CODE, CSA B149.1.
Hot
Side of
If not installed, and maintained in accordance with the
green
Neutral Receptacle
manufacturer's instructions, this product could expose
ground
Side of
Screw
Receptacle
you to substances in fuel or fuel combustion which are
known to the state of California to cause cancer, birth
defects, or other reproductive harm.
* For a copy of the homeowner's care and operation
manual, go to www.lennox.com or call 1-800-9-lennox.
G = Green PU = Purple P = Pink
GY = Gray W = White Y = Yellow
O= Orange R = Red
PROFLAME
ELECTRONIC
VALVE
Y
O
G
W
W
W
G G
P, BL
UNIT MOUNTED * Unit Mounted Rocker Switch
ROCKER SWITCH* OFF (o) = Intermittent Pilot Mode
ON (-) = Standing Pilot Mode
P, BL
0.25" Ø
WARNINg
Black
junction Box
j-BOx / RECEPTACLE
Red
Tab Intact
120V, 60HZ, 1PH
field Wired
factory Wired
PILOT BURNER
IGNITER-SENSOR
ASSEMBLY
B
PILOT TUBE
B
Y
PROFLAME DFC BOARD
NOTES:
1. If any of the original wire as supplied
must be replaced, use Type AWM 105°C
DFC WIRE HARNESS
- 18 gage wire ONLY.
2. 120 VAC, 60 Hz - Less than 5 Amps.
CAUTION: label all wires prior to discon-
nection when servicing controls. Wiring
errors can cause improper and danger-
ous operation. Verify proper operation
after servicing.
0.375"
0.375"
ground - green
Neutral - White
120 VAC - Black
(Power Supply
Unswitched)
WIRINg
IGNITER ROD
FLAME
SENSOR
SPARK WIRE
CABLE
PILOT SENSOR
CABLE